Qi Sui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qi Sui has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Bingrun Yang
2 shared publicationsDanyang Cheng
2 shared publications- Ning Hu
Key Laboratory of Advanced Structural Materials, Ministry of Education, School of Materials Science and Engineering, Changchun University of Technology, Changchun 130012, China
2 shared publications - Xiaolei Song
Key Laboratory of Advanced Structural Materials, Ministry of Education, Changchun University of Technology, Changchun, CHINA
2 shared publications Xu Ran
2 shared publicationsYing Han
2 shared publications
Latest Publications
- Open Access
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
The Effect of Ultrasonic Treatment on Corrosion and Wear Behaviors of Al0.85CoCrFeNiW0.2 Coatings
High-entropy alloy(HEA) are advanced high-performance materials with excellent comprehensive properties. In this study, Al0.85CoCrFeNiW0.2 HEA cladding layers under different ultrasonic amplitude levels were prepared by ultrasonic-assisted laser cladding technology. Subsequently, the microstructure, phase structure, hardness, friction-wear performance, and corrosion resistance of the cladding layers were characterized and analyzed. The experimental results show that the introduction of ultrasound significantly changes the flow state of the molten pool, promotes the uniform distribution of elements, and refines the grains of the cladding layer. Compared with the cladding layer without ultrasonic assistance, the cladding layer with ultrasonic assistance exhibits a significantly reduced corrosion current density, an extended passivation platform, and the impedance of the specimens first increases and then decreases with the increase of ultrasonic amplitude. The hardness and friction-wear performance are improved: the friction coefficient of the cladding layer with the best performance is reduced by 11.8% compared with the original specimen, and the minimum wear rate is reduced by 0.43×10⁻⁴ mm³/(N·m) compared with the original specimen. After ultrasonic assistance, the wear surface of the cladding layer is smoother, the furrows and spalling phenomena are significantly reduced, and the wear rate is greatly decreased.
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessThe Effect of Ultrasonic Treatment on Corrosion and Wear Behaviors of Al0.85CoCrFeNiW0.2 Coatings
High-entropy alloy(HEA) are advanced high-performance materials with excellent comprehensive properties. In this study, Al0.85CoCrFeNiW0.2 HEA cladding layers under different ultrasonic amplitude levels were prepared by ultrasonic-assisted laser cladding technology. Subsequently, the microstructure, phase structure, hardness, friction-wear performance, and corrosion resistance of the cladding layers were characterized and analyzed. The experimental results show that the introduction of ultrasound significantly changes the flow state of the molten pool, promotes the uniform distribution of elements, and refines the grains of the cladding layer. Compared with the cladding layer without ultrasonic assistance, the cladding layer with ultrasonic assistance exhibits a significantly reduced corrosion current density, an extended passivation platform, and the impedance of the specimens first increases and then decreases with the increase of ultrasonic amplitude. The hardness and friction-wear performance are improved: the friction coefficient of the cladding layer with the best performance is reduced by 11.8% compared with the original specimen, and the minimum wear rate is reduced by 0.43×10⁻⁴ mm³/(N·m) compared with the original specimen. After ultrasonic assistance, the wear surface of the cladding layer is smoother, the furrows and spalling phenomena are significantly reduced, and the wear rate is greatly decreased.
- Open Access
- 30 October 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (11) , 2017
Tensile Property of 7075 Aluminum Alloy with Strengthening Layer by Laser Remelting-Cladding Treatment
The Ni60-SiC-CeO2 strengthening layer with deep remelting pools was constructed on the surface of 7075 aluminum alloy using the laser remelting-cladding processing method, and a soft and hard interphase was prepared on the matrix by the interval of laser remelting, which was inspired by soft–hard interphase structure with excellent crack inhibition performance from the natural world. The microstructure and microhardness of the remelting region and the remelting-cladding region of the strengthening layer were studied. The tensile characteristics of two distinct strengthening layers were investigated in the laboratory. The results showed that the grain size of remelting pools is finer, and the microhardness is higher than that of the matrix, which makes crack propagation more difficult. In addition, the results show that the strengthening layer has compact and flawless microstructure and has been metallurgically integrated with the matrix, and the microhardness of the regions treated by laser cladding and laser remelting-cladding has been improved obviously. Toughness has improved, as has the problem of toughness reduction after cladding ceramic particles. The sample’s strength is also significantly greater than that of the untreated sample.
- 30 October 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (11) , 2017
Open AccessTensile Property of 7075 Aluminum Alloy with Strengthening Layer by Laser Remelting-Cladding Treatment
The Ni60-SiC-CeO2 strengthening layer with deep remelting pools was constructed on the surface of 7075 aluminum alloy using the laser remelting-cladding processing method, and a soft and hard interphase was prepared on the matrix by the interval of laser remelting, which was inspired by soft–hard interphase structure with excellent crack inhibition performance from the natural world. The microstructure and microhardness of the remelting region and the remelting-cladding region of the strengthening layer were studied. The tensile characteristics of two distinct strengthening layers were investigated in the laboratory. The results showed that the grain size of remelting pools is finer, and the microhardness is higher than that of the matrix, which makes crack propagation more difficult. In addition, the results show that the strengthening layer has compact and flawless microstructure and has been metallurgically integrated with the matrix, and the microhardness of the regions treated by laser cladding and laser remelting-cladding has been improved obviously. Toughness has improved, as has the problem of toughness reduction after cladding ceramic particles. The sample’s strength is also significantly greater than that of the untreated sample.
- Open Access
- 12 May 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 24, 8793-8806
Hardness difference effect of biomimetic surface with hard-soft structure on oil - Lubrication wear resistance
- 12 May 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 24, 8793-8806
Open AccessHardness difference effect of biomimetic surface with hard-soft structure on oil - Lubrication wear resistance
- Open Access
- 10 February 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (2) , 418
Effect of Reticulate Unit Spacing on Microstructure and Properties of Biomimetic 7075 Aluminum Alloy by Laser Cladding
In the context of energy conservation and emission reduction, more and more attention has been paid to the development of lightweight metal materials with both high strength and high toughness. Inspired by the non-smooth surface of natural organisms, a biomimetic surface with various spacing reticulate units of 7075 aluminum alloys was modified by laser cladding. The microstructure, microhardness and tensile properties of the various spacing units with CeO2-SiC-Ni60 were studied. The finer microstructure and the higher microhardness of various spacing units in comparison with that of 7075 aluminum alloys were obtained, no matter the strip-like treated region or the cross-junction region. Moreover, the best combination of strength and toughness of the biomimetic sample with 2.5 mm spacing reticulate unit was discussed. Finally, by combining the microstructure, XRD phase change, thermal gradient effect, thermal expansion coefficient difference and hard phase strengthening mechanism, it was concluded that the 2.5 mm spacing reticulate unit had the best ability to inhibit crack propagation, and the dispersive hard phases of Al3Ni2 and SiC played a major role in stress release of the matrix.
- 10 February 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (2) , 418
Open AccessEffect of Reticulate Unit Spacing on Microstructure and Properties of Biomimetic 7075 Aluminum Alloy by Laser Cladding
In the context of energy conservation and emission reduction, more and more attention has been paid to the development of lightweight metal materials with both high strength and high toughness. Inspired by the non-smooth surface of natural organisms, a biomimetic surface with various spacing reticulate units of 7075 aluminum alloys was modified by laser cladding. The microstructure, microhardness and tensile properties of the various spacing units with CeO2-SiC-Ni60 were studied. The finer microstructure and the higher microhardness of various spacing units in comparison with that of 7075 aluminum alloys were obtained, no matter the strip-like treated region or the cross-junction region. Moreover, the best combination of strength and toughness of the biomimetic sample with 2.5 mm spacing reticulate unit was discussed. Finally, by combining the microstructure, XRD phase change, thermal gradient effect, thermal expansion coefficient difference and hard phase strengthening mechanism, it was concluded that the 2.5 mm spacing reticulate unit had the best ability to inhibit crack propagation, and the dispersive hard phases of Al3Ni2 and SiC played a major role in stress release of the matrix.
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Effect of Reticulate Unit Spacing on Microstructure and Properties of Biomimetic 7075 Aluminum Alloy by Laser Cladding
In the context of energy conservation and emission reduction, more and more attention has been paid to the development of lightweight metal materials with both high strength and high toughness. Inspired by non-smooth surface of natural organisms, biomimetic surface with vary spacings reticulate units of 7075 aluminum alloys had been modified by laser cladding. The microstructure, microhardness and tensile properties of the vary spacing units with CeO 2 -SiC-Ni 60 were studied. The finer microstructure and the higher microhardness of vary spacing units than that of 7075 aluminum alloys were obtained, no matter at the strip-like treated region or at the cross-junction region. Moreover, the best combination of strength and toughness of the biomimetic sample with 2.5 mm spacing reticulate unit was discussed. Finally, by combining the microstructure, XRD phase change, thermal gradient effect, thermal expansion coefficient difference and hard phase strengthening mechanism, it was concluded that 2.5 mm spacing reticulate unit had the best ability to inhibit crack propagation, and the dispersive hard phases of Al 3 Ni 2 and Al 4 C 3 played a major role in stress release of the matrix.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Reticulate Unit Spacing on Microstructure and Properties of Biomimetic 7075 Aluminum Alloy by Laser Cladding
In the context of energy conservation and emission reduction, more and more attention has been paid to the development of lightweight metal materials with both high strength and high toughness. Inspired by non-smooth surface of natural organisms, biomimetic surface with vary spacings reticulate units of 7075 aluminum alloys had been modified by laser cladding. The microstructure, microhardness and tensile properties of the vary spacing units with CeO 2 -SiC-Ni 60 were studied. The finer microstructure and the higher microhardness of vary spacing units than that of 7075 aluminum alloys were obtained, no matter at the strip-like treated region or at the cross-junction region. Moreover, the best combination of strength and toughness of the biomimetic sample with 2.5 mm spacing reticulate unit was discussed. Finally, by combining the microstructure, XRD phase change, thermal gradient effect, thermal expansion coefficient difference and hard phase strengthening mechanism, it was concluded that 2.5 mm spacing reticulate unit had the best ability to inhibit crack propagation, and the dispersive hard phases of Al 3 Ni 2 and Al 4 C 3 played a major role in stress release of the matrix.