Cevdet Söğütlü
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Cevdet Söğütlü has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Kenan Kılıç
Yozgat Bozok Üniversitesi
4 shared publications - Nihat Döngel
Gazi Üniversitesi
3 shared publications - Hilal Ulaşan
Gazi Univ, Fac Technol Ankara, Dept Wood Prod Ind Engn, Ankara, Turkiye
2 shared publications - Agron Bajraktari
University of Applied Sciences in Ferizaj
1 shared publication - Agron Bajraktari
Faculty of Tourism and Environment, University of Applied Sciences in Ferizaj, 70000 Ferizaj, Kosovo
1 shared publication - Bujar Jashari
University of Applied Sciences in Ferizaj
1 shared publication
Latest Publications
- 30 June 2026
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 9 (1) , 115-129
Ergonomic mismatch between classroom furniture and anthropometric characteristics of university students
Prolonged sitting adversely affects students' physical well-being and academic performance. This study provides a detailed anthropometric analysis evaluating 13 different body parameters across 102 students of the Green Architecture and Interior Design program at the University of Applied Sciences in Ferizaj, Kosovo, to determine the ergonomic reference dimensions for school furniture (chair and desk). The data were evaluated through descriptive statistical indicators, including the mean, standard deviation, and percentiles. The application of the One-Sample T-Test rejected the null hypothesis, confirming statistically significant discrepancies between the current furniture and the recommended dimensions. The primary mismatches were identified in the height of the seat and desk, where the existing dimensions consistently exceed ergonomic standards. In the comparative analysis, model 1 provided a more favorable fit than model 2, which showed more pronounced discrepancies in the height parameters. These empirical findings constitute a valuable basis and a practical framework for designing ergonomic furniture, directly contributing to the optimization of learning spaces, enhancing sitting comfort, and consequently, elevating the overall quality of the learning process.
- 30 June 2026
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 9 (1) , 115-129
Ergonomic mismatch between classroom furniture and anthropometric characteristics of university students
Prolonged sitting adversely affects students' physical well-being and academic performance. This study provides a detailed anthropometric analysis evaluating 13 different body parameters across 102 students of the Green Architecture and Interior Design program at the University of Applied Sciences in Ferizaj, Kosovo, to determine the ergonomic reference dimensions for school furniture (chair and desk). The data were evaluated through descriptive statistical indicators, including the mean, standard deviation, and percentiles. The application of the One-Sample T-Test rejected the null hypothesis, confirming statistically significant discrepancies between the current furniture and the recommended dimensions. The primary mismatches were identified in the height of the seat and desk, where the existing dimensions consistently exceed ergonomic standards. In the comparative analysis, model 1 provided a more favorable fit than model 2, which showed more pronounced discrepancies in the height parameters. These empirical findings constitute a valuable basis and a practical framework for designing ergonomic furniture, directly contributing to the optimization of learning spaces, enhancing sitting comfort, and consequently, elevating the overall quality of the learning process.
- 19 February 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 515
Surface roughness–varnish adhesion relationship in heat-treated wood
- 19 February 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 515
Surface roughness–varnish adhesion relationship in heat-treated wood
- Open Access
- 4 December 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (6) , 1755-1770
Afyon Paşa Camii (Umur Bey Cami) Ahşap Donatı Elemanlarının Malzeme ve Yapım Tekniği Açısından İncelenmesi
Bu çalışma, dini yapılarda yaygın olarak kullanılan geleneksel kündekâri tekniğinin günümüzdeki uygulamalarını incelemeyi ve bu tekniğin korunması ile sürdürülebilirliğine yönelik öneriler geliştirmeyi amaçlamaktadır. Kündekâri, hem estetik hem de teknik açıdan önemli bir değere sahip bir işçilik yöntemidir. Ahşap malzeme, çevresel etkilere karşı korunması gereken bir malzeme olup, doğru malzeme seçimi ve yüksek işçilikle yapılan üretimle bu etkilere karşı koruma sağlanabilir. Çalışma, Paşa Cami örneği üzerinden yapılan incelemelerle, kündekâri tekniğiyle üretilen donatı elemanlarının günümüz teknolojisiyle üretilmesi sonucu mimari yapıya uyum sağlama durumlarını ve bu elemanların uzun ömürlü olma özelliklerini ele almıştır. Paşa Cami'deki ana giriş kapısı, minber, mihrap, müezzin mahfili ve sabit vaaz kürsüsü gibi donatı elemanlarında, doğru malzeme seçimi ve yüksek işçilikle yapılan üretimler gözlemlenmiştir. Ancak, caminin diğer bazı donatı elemanlarında kullanılan modern malzemelerin caminin genel mimarisine uyum sağlamadığı ve kültürel mirasın sürdürülebilirliğine olumsuz etkilerde bulunduğu tespit edilmiştir. Bu bağlamda, geleneksel malzemelerin tercih edilmesi, kündekâri tekniğinin özgün detaylarının korunması ve nitelikli zanaatkârların yetiştirilmesi gerektiği vurgulanmıştır. Ayrıca, eğitim programları ve atölye çalışmalarıyla geleneksel tekniklerin yeni nesillere aktarılması önerilmektedir. Sonuç olarak, bu çalışma, kündekâri tekniğinin korunması ve sürdürülebilirliğinin sağlanması için doğru malzeme seçimi, yüksek işçilik ve uygun koruma yöntemlerinin önemini ortaya koymakta, bu geleneksel tekniğin yaşatılması için gerekli önerileri sunmaktadır.
- 4 December 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (6) , 1755-1770
Open AccessAfyon Paşa Camii (Umur Bey Cami) Ahşap Donatı Elemanlarının Malzeme ve Yapım Tekniği Açısından İncelenmesi
Bu çalışma, dini yapılarda yaygın olarak kullanılan geleneksel kündekâri tekniğinin günümüzdeki uygulamalarını incelemeyi ve bu tekniğin korunması ile sürdürülebilirliğine yönelik öneriler geliştirmeyi amaçlamaktadır. Kündekâri, hem estetik hem de teknik açıdan önemli bir değere sahip bir işçilik yöntemidir. Ahşap malzeme, çevresel etkilere karşı korunması gereken bir malzeme olup, doğru malzeme seçimi ve yüksek işçilikle yapılan üretimle bu etkilere karşı koruma sağlanabilir. Çalışma, Paşa Cami örneği üzerinden yapılan incelemelerle, kündekâri tekniğiyle üretilen donatı elemanlarının günümüz teknolojisiyle üretilmesi sonucu mimari yapıya uyum sağlama durumlarını ve bu elemanların uzun ömürlü olma özelliklerini ele almıştır. Paşa Cami'deki ana giriş kapısı, minber, mihrap, müezzin mahfili ve sabit vaaz kürsüsü gibi donatı elemanlarında, doğru malzeme seçimi ve yüksek işçilikle yapılan üretimler gözlemlenmiştir. Ancak, caminin diğer bazı donatı elemanlarında kullanılan modern malzemelerin caminin genel mimarisine uyum sağlamadığı ve kültürel mirasın sürdürülebilirliğine olumsuz etkilerde bulunduğu tespit edilmiştir. Bu bağlamda, geleneksel malzemelerin tercih edilmesi, kündekâri tekniğinin özgün detaylarının korunması ve nitelikli zanaatkârların yetiştirilmesi gerektiği vurgulanmıştır. Ayrıca, eğitim programları ve atölye çalışmalarıyla geleneksel tekniklerin yeni nesillere aktarılması önerilmektedir. Sonuç olarak, bu çalışma, kündekâri tekniğinin korunması ve sürdürülebilirliğinin sağlanması için doğru malzeme seçimi, yüksek işçilik ve uygun koruma yöntemlerinin önemini ortaya koymakta, bu geleneksel tekniğin yaşatılması için gerekli önerileri sunmaktadır.
- 19 September 2024
- Published by Pulp and Paper Research Institute in Wood Research
- Vol. 69 (3) , 402-416
THE EFFECT OF SUPPORT LAYER MATERIAL AND ADHESIVE TYPE ON COMPRESSIVE DYNAMIC BENDING AND SHEAR STRENGTH IN LAMINATED WOOD
In this study, strength properties of wood material reinforced with carbon fiber fabric, steel wire mesh and bamboo veneer were determined. Polyvinylacetate (PVAc) and polyurethane (PUR) glues (D4)were used for the lamellas obtained from Scotch pine (Pinus sylvestris L.) and eastern beech (Fagus orientalis L.). Compressive strength according to TS EN 408+A1; dynamic bending (shock) strength according toTS ISO 13061-10 and shear strength according to ASTM D 3110 were determined on 3 and 5-layers samples. According to the results, the highest compressive strength (62.8 N/mm2) was found in 5-layerseastern beech samples reinforced with carbon fiber fabric and bonded with PUR glue. The highest dynamic bending strength value (110.8 kJ/m2) was found in 5-layerseastern beech samples reinforced with carbon fiber fabric and bonded with PUR glue and the highest shear strength value (12.3 N/mm2) in 3-layered eastern beech samples reinforced with steel wire mesh and bonded with PUR glue.
- 19 September 2024
- Published by Pulp and Paper Research Institute in Wood Research
- Vol. 69 (3) , 402-416
THE EFFECT OF SUPPORT LAYER MATERIAL AND ADHESIVE TYPE ON COMPRESSIVE DYNAMIC BENDING AND SHEAR STRENGTH IN LAMINATED WOOD
In this study, strength properties of wood material reinforced with carbon fiber fabric, steel wire mesh and bamboo veneer were determined. Polyvinylacetate (PVAc) and polyurethane (PUR) glues (D4)were used for the lamellas obtained from Scotch pine (Pinus sylvestris L.) and eastern beech (Fagus orientalis L.). Compressive strength according to TS EN 408+A1; dynamic bending (shock) strength according toTS ISO 13061-10 and shear strength according to ASTM D 3110 were determined on 3 and 5-layers samples. According to the results, the highest compressive strength (62.8 N/mm2) was found in 5-layerseastern beech samples reinforced with carbon fiber fabric and bonded with PUR glue. The highest dynamic bending strength value (110.8 kJ/m2) was found in 5-layerseastern beech samples reinforced with carbon fiber fabric and bonded with PUR glue and the highest shear strength value (12.3 N/mm2) in 3-layered eastern beech samples reinforced with steel wire mesh and bonded with PUR glue.
- Open Access
- 1 January 2024
- Published by Kastamonu University in Kastamonu University Journal of Forestry Faculty
- Vol. 24 (1) , 59-73
Color Change Analysis of Wood Materials Treated with Different Varnishes: A Comparative Study
Aim of the study: This study examines the overall color change values from applying water-based, polyurethane, and acrylic varnishes on newly prepared and naturally aged wood materials. Materials and methods: The Turkish woodworking industry commonly selects oak (Quercus petrea L.), chestnut (Castanea sativa M.), and scotch pine (Pinus sylvestris L.) as the preferred wood type for preparing test samples. A total of 360 test samples are prepared for the experiments. The color difference (ΔE*) between two colors is measured using a Minolta CR-231 color measurement device, following the principles outlined in ASTM-D 2244. Main results: On the C.I.E. Lab* color plane, a higher ΔE* indicates a more significant difference between the compared colors. Among the wood type, oak exhibited the highest color change (ΔE*), while chestnut displayed the lowest. Fresh wood materials showed higher color change values (ΔE*) than naturally aged wood materials. The radial section direction also is showed higher color change values (ΔE*) than the tangential section direction. Research highlights: Regarding varnish type, acrylic varnish indicated a minor color change, followed by polyurethane and water-based varnishes, respectively. Acrylic varnish is recommended for studies with minimal color change and for preserving the wood material's natural color.
- 1 January 2024
- Published by Kastamonu University in Kastamonu University Journal of Forestry Faculty
- Vol. 24 (1) , 59-73
Open AccessColor Change Analysis of Wood Materials Treated with Different Varnishes: A Comparative Study
Aim of the study: This study examines the overall color change values from applying water-based, polyurethane, and acrylic varnishes on newly prepared and naturally aged wood materials. Materials and methods: The Turkish woodworking industry commonly selects oak (Quercus petrea L.), chestnut (Castanea sativa M.), and scotch pine (Pinus sylvestris L.) as the preferred wood type for preparing test samples. A total of 360 test samples are prepared for the experiments. The color difference (ΔE*) between two colors is measured using a Minolta CR-231 color measurement device, following the principles outlined in ASTM-D 2244. Main results: On the C.I.E. Lab* color plane, a higher ΔE* indicates a more significant difference between the compared colors. Among the wood type, oak exhibited the highest color change (ΔE*), while chestnut displayed the lowest. Fresh wood materials showed higher color change values (ΔE*) than naturally aged wood materials. The radial section direction also is showed higher color change values (ΔE*) than the tangential section direction. Research highlights: Regarding varnish type, acrylic varnish indicated a minor color change, followed by polyurethane and water-based varnishes, respectively. Acrylic varnish is recommended for studies with minimal color change and for preserving the wood material's natural color.
- 4 July 2023
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 26 (2) , 847-854
Varnish Adhesion Strength in Natural Aged Wood Material
This study, it is aimed to determine the adhesion strength of varnish layers applied to the surface of fresh and naturally aged wood materials. For this purpose, oak (Quercus Petrea L.), chestnut (Castanea sativa M.) and Scots pine (Pinus sylvestris L.) wood materials were used for each wood species, age period, section direction and varnish type. A total of 360 test samples were prepared and polyurethane, acrylic and water-based varnishes were applied to their surfaces. The adhesion strength of the samples was determined by the pull-off test following TS EN 4624. The statistical analyzes of the data obtained as a result of the experiments were made with the MSTAT-C package software, and the significance values between and within the groups were determined. According to the results of the research, it was determined that the age period did not affect the varnish adhesion strength the highest adhesion strength at the wood species level was obtained in chestnut (3.361 N/mm2), followed by oak (3.191 N/mm2) and Scots pine (2.248 N/mm2). At the varnish type level, the highest adhesion strength was obtained in polyurethane varnish (4.009 N/mm2), followed by acrylic varnish (3.754 N/mm2) and water-based varnish (1.286 N/mm2), respectively. In the section direction comparisons, the adhesion strength was found higher in the tangential direction (3.098 N/mm2) and higher in the radial direction (2.935 N/mm2). In the comparison level of age period-varnish type, the highest was obtained in polyurethane varnish (4.307 N/mm2) applied to the surface of naturally aged wood material, and the lowest was obtained in water-based varnish (1,167 N/mm2) applied to the surface of naturally aged wood material.
- 4 July 2023
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 26 (2) , 847-854
Varnish Adhesion Strength in Natural Aged Wood Material
This study, it is aimed to determine the adhesion strength of varnish layers applied to the surface of fresh and naturally aged wood materials. For this purpose, oak (Quercus Petrea L.), chestnut (Castanea sativa M.) and Scots pine (Pinus sylvestris L.) wood materials were used for each wood species, age period, section direction and varnish type. A total of 360 test samples were prepared and polyurethane, acrylic and water-based varnishes were applied to their surfaces. The adhesion strength of the samples was determined by the pull-off test following TS EN 4624. The statistical analyzes of the data obtained as a result of the experiments were made with the MSTAT-C package software, and the significance values between and within the groups were determined. According to the results of the research, it was determined that the age period did not affect the varnish adhesion strength the highest adhesion strength at the wood species level was obtained in chestnut (3.361 N/mm2), followed by oak (3.191 N/mm2) and Scots pine (2.248 N/mm2). At the varnish type level, the highest adhesion strength was obtained in polyurethane varnish (4.009 N/mm2), followed by acrylic varnish (3.754 N/mm2) and water-based varnish (1.286 N/mm2), respectively. In the section direction comparisons, the adhesion strength was found higher in the tangential direction (3.098 N/mm2) and higher in the radial direction (2.935 N/mm2). In the comparison level of age period-varnish type, the highest was obtained in polyurethane varnish (4.307 N/mm2) applied to the surface of naturally aged wood material, and the lowest was obtained in water-based varnish (1,167 N/mm2) applied to the surface of naturally aged wood material.
- 20 June 2023
- Published by University of Zagreb, Faculty of Forestry and Wood Technology in Drvna industrija
- Vol. 74 (2) , 153-166
Prediction of Adhesion Strength of Some Varnishes Using Soft Computing Models
The purpose of this study was to predict the adhesion strength of the varnish, which is applied as a protective coating/finish on the surface of wooden material using soft computing models. In this study, the soft computing approaches were applied to oak (Quercus Petrea L.), chestnut (Castanea sativa M.), and scotch pine (Pinus sylvestris L.) with water-based, polyurethane, and acrylic varnishes. The adhesion strength of the varnish was determined in accordance with the Turkish Standard Institute-24624 and ASTM D4541. The outcome of the experiment was used to develop artificial neural network (ANN) and fuzzy logic (FL) prediction models. The total number of 360 data points was split as 80 % of training and 20 % of test for the model development. During the application of the ANN, 6 features were used as an input, while the adhesion strength was used as an output of the model. The coefficient of determination values (R2) for training and testing in the ANN models were 0.9939 and 0.9580, respectively. In the case of the ANFIS model, R2 values for training and testing were 0.9917 and 0.9929, respectively. Considering the MAPE, RMSE, and R2 values obtained from the results of both training and test values, it can be concluded that the ANFIS model showed a more successful performance in estimating varnish adhesion strength. Therefore, ANN and ANFIS have the potential to provide time and cost-efficient benefits in estimating wood adhesion strength.
- 20 June 2023
- Published by University of Zagreb, Faculty of Forestry and Wood Technology in Drvna industrija
- Vol. 74 (2) , 153-166
Prediction of Adhesion Strength of Some Varnishes Using Soft Computing Models
The purpose of this study was to predict the adhesion strength of the varnish, which is applied as a protective coating/finish on the surface of wooden material using soft computing models. In this study, the soft computing approaches were applied to oak (Quercus Petrea L.), chestnut (Castanea sativa M.), and scotch pine (Pinus sylvestris L.) with water-based, polyurethane, and acrylic varnishes. The adhesion strength of the varnish was determined in accordance with the Turkish Standard Institute-24624 and ASTM D4541. The outcome of the experiment was used to develop artificial neural network (ANN) and fuzzy logic (FL) prediction models. The total number of 360 data points was split as 80 % of training and 20 % of test for the model development. During the application of the ANN, 6 features were used as an input, while the adhesion strength was used as an output of the model. The coefficient of determination values (R2) for training and testing in the ANN models were 0.9939 and 0.9580, respectively. In the case of the ANFIS model, R2 values for training and testing were 0.9917 and 0.9929, respectively. Considering the MAPE, RMSE, and R2 values obtained from the results of both training and test values, it can be concluded that the ANFIS model showed a more successful performance in estimating varnish adhesion strength. Therefore, ANN and ANFIS have the potential to provide time and cost-efficient benefits in estimating wood adhesion strength.
- Open Access
Modulus of Elasticity and Flexural Behavior of Glulam Beams Reinforced with Steel Mesh in Different Mesh Openings
In this study, the modulus of elasticity and flexural strength properties of laminated wood elements reinforced with steel mesh with different mesh openings were determined. In accordance with the purpose of the study, three- and five-layer laminated elements were produced from scotch pine (Pinus sylvestris L.) wood material, which is widely used in the wood construction industry in Türkiye. The 50, 70, and 90 mesh steel used as the support layer was placed between each lamella and pressed with polyvinylacetate (PVAc-D4) and polyurethane (PUR-D4) adhesives. Afterward, the prepared test samples were kept for 3 weeks at 20 °C temperature and 65 ± 5% relative humidity for 3 weeks. The flexural strength and modulus of elasticity in flexural of the prepared test samples were determined according to the TS EN 408: 2010+A1 standard by the Zwick universal tester. Multiple analysis of variance (MANOVA) was carried out using MSTAT-C 1.2 software to determine the effect of the modulus of elasticity and flexural strength on the obtained flexural properties, the mesh opening of the support layer, and the adhesive type. When the differences within or between groups were significant with a margin of error of 0.05, achievement rankings were made using the Duncan test on the basis of the least significant difference. According to the results of the research, the highest bending strength (120.3 N/mm2) was obtained in three-layer samples reinforced with 50 mesh steel wire and bonded with Pol-D4 glue, and the highest modulus of elasticity (8969.3 N/mm2) was obtained in three-layer samples reinforced with 50 mesh steel wire and bonded with Pol-D4 glue. As a result, the reinforcement of the laminated wood material with steel wire had an increasing effect on the strength. Accordingly, the use of 50 mesh steel wire can be recommended to increase mechanical properties.
Open AccessModulus of Elasticity and Flexural Behavior of Glulam Beams Reinforced with Steel Mesh in Different Mesh Openings
In this study, the modulus of elasticity and flexural strength properties of laminated wood elements reinforced with steel mesh with different mesh openings were determined. In accordance with the purpose of the study, three- and five-layer laminated elements were produced from scotch pine (Pinus sylvestris L.) wood material, which is widely used in the wood construction industry in Türkiye. The 50, 70, and 90 mesh steel used as the support layer was placed between each lamella and pressed with polyvinylacetate (PVAc-D4) and polyurethane (PUR-D4) adhesives. Afterward, the prepared test samples were kept for 3 weeks at 20 °C temperature and 65 ± 5% relative humidity for 3 weeks. The flexural strength and modulus of elasticity in flexural of the prepared test samples were determined according to the TS EN 408: 2010+A1 standard by the Zwick universal tester. Multiple analysis of variance (MANOVA) was carried out using MSTAT-C 1.2 software to determine the effect of the modulus of elasticity and flexural strength on the obtained flexural properties, the mesh opening of the support layer, and the adhesive type. When the differences within or between groups were significant with a margin of error of 0.05, achievement rankings were made using the Duncan test on the basis of the least significant difference. According to the results of the research, the highest bending strength (120.3 N/mm2) was obtained in three-layer samples reinforced with 50 mesh steel wire and bonded with Pol-D4 glue, and the highest modulus of elasticity (8969.3 N/mm2) was obtained in three-layer samples reinforced with 50 mesh steel wire and bonded with Pol-D4 glue. As a result, the reinforcement of the laminated wood material with steel wire had an increasing effect on the strength. Accordingly, the use of 50 mesh steel wire can be recommended to increase mechanical properties.
- 1 December 2020
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 23 (4) , 1423-1431
The Determination of Gloss Values of Some Varnishes Applied on the Natural Aged Wood
Bu çalışmada, doğal yaşlanmış ve yeni ağaç odunları üzerine uygulanan bazı verniklerin yüzey parlaklık değerleri (Gloss) araştırılmıştır. Her bir ağaç türü (3), kesit yönü (2), yaş periyodu (2) ve vernik çeşidi (3) deneme desenine göre 10’ar adet tekerrür olmak üzere toplam 360 adet deney örneği hazırlanmıştır. Doğal yaşlanmış ve yeni sarıçam (Pinus sylvestris L.), sapsız meşe (Quercus petrea L.) ve kestane (Castanea sativa M.) odunlarından hazırlanan deney örneklerine, ASTM-D 3023 standardı esaslarına göre, iki kat dolgu ve iki kat son kat vernik olmak üzere ipek mat su bazlı, ipek-mat poliüretan ve ipek-mat akrilik vernikler püskürtme tabancası ile uygulamıştır. Örneklerin yüzey parlaklıkları, TS EN ISO 2813 standardındaki esaslara uygun olarak belirlenmiştir. Deney sonuçlarına göre, yüzey parlaklığı yeni odunda (37,14) doğal yaşlanmış odundan (36,45) yüksek bulunmuştur. Ağaç türü düzeyinde, en yüksek sarıçamda (38,46) elde edilirken, sapsız meşe (35,89) ile kestane (36,04) arasındaki fark önemsiz çıkmıştır. Vernik çeşidi düzeyinde en yüksek parlaklık değeri poliüretan vernikte (39,88) elde edilmiş, bunu sırasıyla akrilik vernik (37,20) ve su-bazlı vernik (33,32) takip etmiştir.
- 1 December 2020
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 23 (4) , 1423-1431
The Determination of Gloss Values of Some Varnishes Applied on the Natural Aged Wood
Bu çalışmada, doğal yaşlanmış ve yeni ağaç odunları üzerine uygulanan bazı verniklerin yüzey parlaklık değerleri (Gloss) araştırılmıştır. Her bir ağaç türü (3), kesit yönü (2), yaş periyodu (2) ve vernik çeşidi (3) deneme desenine göre 10’ar adet tekerrür olmak üzere toplam 360 adet deney örneği hazırlanmıştır. Doğal yaşlanmış ve yeni sarıçam (Pinus sylvestris L.), sapsız meşe (Quercus petrea L.) ve kestane (Castanea sativa M.) odunlarından hazırlanan deney örneklerine, ASTM-D 3023 standardı esaslarına göre, iki kat dolgu ve iki kat son kat vernik olmak üzere ipek mat su bazlı, ipek-mat poliüretan ve ipek-mat akrilik vernikler püskürtme tabancası ile uygulamıştır. Örneklerin yüzey parlaklıkları, TS EN ISO 2813 standardındaki esaslara uygun olarak belirlenmiştir. Deney sonuçlarına göre, yüzey parlaklığı yeni odunda (37,14) doğal yaşlanmış odundan (36,45) yüksek bulunmuştur. Ağaç türü düzeyinde, en yüksek sarıçamda (38,46) elde edilirken, sapsız meşe (35,89) ile kestane (36,04) arasındaki fark önemsiz çıkmıştır. Vernik çeşidi düzeyinde en yüksek parlaklık değeri poliüretan vernikte (39,88) elde edilmiş, bunu sırasıyla akrilik vernik (37,20) ve su-bazlı vernik (33,32) takip etmiştir.
- 8 August 2016
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 13 (5) , 863-870
The effects of surface roughness on varnish adhesion strength of wood materials
- 8 August 2016
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 13 (5) , 863-870
The effects of surface roughness on varnish adhesion strength of wood materials