Vinit Kumar Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Vinit Kumar Singh has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Amrita Kundu
Jadavpur University
2 shared publications- Gianluca Lazzi
University of Southern California
2 shared publications - Radhakanta Rana
Tata Steel, Ijmuiden, The Netherlands
2 shared publications - Shiv Brat Singh
Department of Metallurgical and Materials Engineering, Indian Institute of Technology Kharagpur, Kharagpur, India
2 shared publications - Amrita Kundu
Jadavpur University
1 shared publication - Amrita Kundu
Jadavpur University
1 shared publication
Latest Publications
- 28 March 2026
- Published by SAGE Publications in Materials Science and Technology
Critical assessment: Processing, microstructure and mechanical properties of Al-containing ferrite-based low-density steels
Over the past three decades, research on aluminium (Al)-containing low-density steels (LDS) has accelerated due to their ∼8–15% lower density than conventional steels, increasing their demand in lightweight automotive applications, high-temperature applications and cryogenic uses such as storage tanks and spacecraft. This review focuses on Al-containing ferritic low-density steels (FLDS). It begins with a discussion of the formation of the κ-carbide and B2/DO 3 phases, the melting and casting route, followed by an overview of microstructural evolution. Furthermore, the elastic modulus, effects of microalloying elements on mechanical properties, deformation mechanisms and the influences of microstructure and strain-hardening behaviour on tensile properties are critically reviewed. Finally, future research directions for optimising the microstructure–mechanical property relationships in FLDS are discussed.
- 28 March 2026
- Published by SAGE Publications in Materials Science and Technology
Critical assessment: Processing, microstructure and mechanical properties of Al-containing ferrite-based low-density steels
Over the past three decades, research on aluminium (Al)-containing low-density steels (LDS) has accelerated due to their ∼8–15% lower density than conventional steels, increasing their demand in lightweight automotive applications, high-temperature applications and cryogenic uses such as storage tanks and spacecraft. This review focuses on Al-containing ferritic low-density steels (FLDS). It begins with a discussion of the formation of the κ-carbide and B2/DO 3 phases, the melting and casting route, followed by an overview of microstructural evolution. Furthermore, the elastic modulus, effects of microalloying elements on mechanical properties, deformation mechanisms and the influences of microstructure and strain-hardening behaviour on tensile properties are critically reviewed. Finally, future research directions for optimising the microstructure–mechanical property relationships in FLDS are discussed.
- 4 June 2024
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 55 (8) , 2990-3010
Strain Rate-Dependent Tensile and Fracture Properties of Low-Carbon Ferritic Low-Density Steels
- 4 June 2024
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 55 (8) , 2990-3010
Strain Rate-Dependent Tensile and Fracture Properties of Low-Carbon Ferritic Low-Density Steels
- 15 October 2023
- Published by Springer Nature
- p. 237-247
Cracking Problem During Room Temperature Cold Rolling of Three High Al Low C Ferritic Low Density-Steels
- 15 October 2023
- Published by Springer Nature
- p. 237-247
Cracking Problem During Room Temperature Cold Rolling of Three High Al Low C Ferritic Low Density-Steels
- Open Access
- 15 May 2023
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 63 (5) , 930-940
Effects of Temperatures of Rolling and Annealing on Microstructures and Tensile Properties of Low Carbon Ferritic Low Density Steels
The microstructural modification and the effect of cold/warm rolling and annealing on tensile properties of ferritic low density steels containing different amounts of carbon (0.0035 mass%, Steel 1 and 0.04 mass%, Steel 2) and aluminium (6.8 mass%, Steel 1 and 9.7 mass%, Steel 2) were investigated with respect to amount of ferrite, grain size and formation of Fe3Al intermetallic. The Steel 1 was deformed by cold rolling at room temperature and Steel 2 was deformed through warm rolling at 250°C to avoid prior cracks formation. After rolling, samples of Steels 1 and 2 were annealed at 900°C for 5 minutes. The yield strength, ultimate tensile strength and ductility increase while yield ratio decreases with annealing. This is due to formation of Fe3Al intermetallic and reduction of ferrite grain size. Due to high interstitial Carbon in Steel 2, yield point phenomenon was observed which may reduce the formability of the steel. The cracks started during tensile test at the ferrite grains and ferrite grain boundaries and the fracture took place in the quasi cleavage mode in Steels 1 and 2. The grain refinement and the microstructural features due to rolling and annealing are accountable for the good combination of strength and ductility of the both steels.
- 15 May 2023
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 63 (5) , 930-940
Open AccessEffects of Temperatures of Rolling and Annealing on Microstructures and Tensile Properties of Low Carbon Ferritic Low Density Steels
The microstructural modification and the effect of cold/warm rolling and annealing on tensile properties of ferritic low density steels containing different amounts of carbon (0.0035 mass%, Steel 1 and 0.04 mass%, Steel 2) and aluminium (6.8 mass%, Steel 1 and 9.7 mass%, Steel 2) were investigated with respect to amount of ferrite, grain size and formation of Fe3Al intermetallic. The Steel 1 was deformed by cold rolling at room temperature and Steel 2 was deformed through warm rolling at 250°C to avoid prior cracks formation. After rolling, samples of Steels 1 and 2 were annealed at 900°C for 5 minutes. The yield strength, ultimate tensile strength and ductility increase while yield ratio decreases with annealing. This is due to formation of Fe3Al intermetallic and reduction of ferrite grain size. Due to high interstitial Carbon in Steel 2, yield point phenomenon was observed which may reduce the formability of the steel. The cracks started during tensile test at the ferrite grains and ferrite grain boundaries and the fracture took place in the quasi cleavage mode in Steels 1 and 2. The grain refinement and the microstructural features due to rolling and annealing are accountable for the good combination of strength and ductility of the both steels.
- 1 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Smart Lights: How it Enhances Connectivity
Connectivity enhances a building’s responsiveness to internal changes as well as its resilience to external challenges. Today, high-performing smart buildings respond to a myriad of internal stimuli. These range from changes in lighting, temperature, ventilation, and occupancy levels to IT data requirements and the operational technology that controls elevators and security apparatus.
- 1 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Smart Lights: How it Enhances Connectivity
Connectivity enhances a building’s responsiveness to internal changes as well as its resilience to external challenges. Today, high-performing smart buildings respond to a myriad of internal stimuli. These range from changes in lighting, temperature, ventilation, and occupancy levels to IT data requirements and the operational technology that controls elevators and security apparatus.
- 18 November 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 2 (4) , 289-300
On the Thermal Elevation of a 60-Electrode Epiretinal Prosthesis for the Blind
In this paper, the thermal elevation in the human body due to the operation of a dual-unit epiretinal prosthesis to restore partial vision to the blind affected by irreversible retinal degeneration is presented. An accurate computational model of a 60-electrode device dissipating 97 mW power, currently under clinical trials is developed and positioned in a 0.25 mm resolution, heterogeneous model of the human head to resemble actual conditions of operation of the prosthesis. A novel simple finite difference scheme combining the explicit and the alternating-direction implicit (ADI) method has been developed and validated with existing methods. Simulation speed improvement up to 11 times was obtained for the the head model considered in this work with very good accuracy. Using this method, solutions of the bioheat equation were obtained for different placements of the implant. Comparison with in-vivo experimental measurements showed good agreement.
- 18 November 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 2 (4) , 289-300
On the Thermal Elevation of a 60-Electrode Epiretinal Prosthesis for the Blind
In this paper, the thermal elevation in the human body due to the operation of a dual-unit epiretinal prosthesis to restore partial vision to the blind affected by irreversible retinal degeneration is presented. An accurate computational model of a 60-electrode device dissipating 97 mW power, currently under clinical trials is developed and positioned in a 0.25 mm resolution, heterogeneous model of the human head to resemble actual conditions of operation of the prosthesis. A novel simple finite difference scheme combining the explicit and the alternating-direction implicit (ADI) method has been developed and validated with existing methods. Simulation speed improvement up to 11 times was obtained for the the head model considered in this work with very good accuracy. Using this method, solutions of the bioheat equation were obtained for different placements of the implant. Comparison with in-vivo experimental measurements showed good agreement.
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 15223965,p. 3213-3216
On the modeling of the electromagnetic fields induced by MRI fields in patients with a retinal implant
In this work, we consider the interaction between MRI fields and a patient with a retinal prosthesis (RP) implant, which is a restorative device being designed to mimic the function of basic photoreceptor cells in patients suffering from outer retinal degeneration caused by age related macular degeneration (AMD) or retinal pigmentosa. This work uses 3D expanding grid finite difference time domain (FDTD) method to calculate the SAR distribution and estimate the thermal elevation when the human head with the implant is exposed to RF magnetic field at 64 MHz. The advantage of using an expanding grid FDTD algorithm is that computer memory requirements are greatly reduced and more accurate modeling of the region of the implant is possible where a finer grid with cell sizes of the order of micrometers is used. This helps to model the RF birdcage coil and the human head with the implant as a single system and simulate the EM interactions of the tissues even at higher frequencies. The power deposition is computed as the average SAR over any 1 g of tissue in the head.
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 15223965,p. 3213-3216
On the modeling of the electromagnetic fields induced by MRI fields in patients with a retinal implant
In this work, we consider the interaction between MRI fields and a patient with a retinal prosthesis (RP) implant, which is a restorative device being designed to mimic the function of basic photoreceptor cells in patients suffering from outer retinal degeneration caused by age related macular degeneration (AMD) or retinal pigmentosa. This work uses 3D expanding grid finite difference time domain (FDTD) method to calculate the SAR distribution and estimate the thermal elevation when the human head with the implant is exposed to RF magnetic field at 64 MHz. The advantage of using an expanding grid FDTD algorithm is that computer memory requirements are greatly reduced and more accurate modeling of the region of the implant is possible where a finer grid with cell sizes of the order of micrometers is used. This helps to model the RF birdcage coil and the human head with the implant as a single system and simulate the EM interactions of the tissues even at higher frequencies. The power deposition is computed as the average SAR over any 1 g of tissue in the head.