Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dunzhu Li has a total of 34 co-authors. Here are the top co-authors by number of shared publications:

  • Liwen Xiao

    Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin, Ireland

    6 shared publications
  • Luming Yang

    Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin 2, Ireland; School of Civil Engineering, Chang'an University, Xi'an, China

    3 shared publications
  • Luming Yang

    Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, D02 PN40 Dublin, Ireland

    3 shared publications
  • Yifan Sun

    Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, D02 PN40 Dublin, Ireland

    3 shared publications
  • Yunhong Shi

    Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, Dublin 2, Ireland

    3 shared publications
  • Yunhong Shi

    Department of Civil, Structural and Environmental Engineering, Trinity College Dublin, D02 PN40 Dublin, Ireland

    3 shared publications

Latest Publications

  • Understanding nitrogen removal mechanisms of microbial fuel cells with different air-cathodes: pathways and microbial community analysis

    by Yifan Sun, Zeena Wang, Dunzhu Li, Yunhong Shi, Shangming Wang, Luming Yang, Zihan Zhang, Wen Zhang, Peiying Kang, Jiazekai Li, et al.


  • Open Access

    Stress drives polymer phase separation and microplastic release

    by Jing Jing Wang, Dunzhu Li, Peijing Li, Yunhong Shi, Emmet Sheerin, Luming Yang, Christopher Hill, John Sader, Conall Gordon, Manuel Ruether, et al.

    Microplastic release from semicrystalline plastics threaten the environment and human health. We investigated polypropylene and polyethylene plastics, which together account for 54% of the global market. Mimicking common levels of residual stress found in plastics via cantilever beam experiments, we demonstrated that compressive stress drives nano and microscale segregation of amorphous polymer droplets onto the plastic’s surface. Simulations reveal this stress-driven volumetric flow is consistent with that of a Bingham plastic material, with a temperature-dependent threshold yield stress. Flow is thermally activated and stress dependent, with a reduced energy barrier at higher compressive stresses. Transfer of surface segregated amorphous droplets into the surroundings generates microplastics. Studies with water-containing plastic bottles showed that the highly compressed neck and mouth regions were predominantly responsible for the release of microplastics.

  • Open Access

    Micro and nano plastics release from a single absorbable suture into simulated body fluid

    by Yunhong Shi, Dunzhu Li, Christopher Hill, Luming Yang, Emmet D. Sheerin, Rekha Pilliadugula, Jing Jing Wang, John Boland, Liwen Xiao


  • Open Access

    Application of 3D Printing Technology in Sensor Development for Water Quality Monitoring

    by Yifan Sun, Dunzhu Li, Yunhong Shi, Zeena Wang, Saviour I. Okeke, Luming Yang, Wen Zhang, Zihan Zhang, Yanqi Shi, Liwen Xiao

    The development of sensors for water quality monitoring is crucial to protect water quality, aquatic biota and human health. Traditional sensor manufacturing methods have significant drawbacks, such as low fabrication freedom, limited material choice and expensive manufacturing cost. As a possible alternative method, 3D printing technologies are increasingly popular in sensor development due to their high versatility, fast fabrication/modification, powerful processing of different materials and ease of incorporation with other sensor systems. Surprisingly, a systematic review examining the application of 3D printing technology in water monitoring sensors has not yet been conducted. Here, we summarized the development history, market share and advantages/disadvantages of typical 3D printing techniques. Specifically focused on the 3D-printed sensor for water quality monitoring, we then reviewed the applications of 3D printing in the development of sensors’ supporting platform, cell, sensing electrode as well as all-3D-printed sensors. The fabrication materials and processing, and the sensor’s performances regarding detected parameters, response time and detection limit/sensitivity, were also compared and analyzed. Finally, the current drawbacks of 3D-printed water sensors and potential directions for future study were discussed. This review will substantially promote the understanding of 3D printing technology used in water sensor development and benefit the protection of water resources.


  • Open Access

    Recent Implementations of Hydrogel-Based Microbial Electrochemical Technologies (METs) in Sensing Applications

    by Zeena Wang, Dunzhu Li, Yunhong Shi, Yifan Sun, Saviour I. Okeke, Luming Yang, Wen Zhang, Zihan Zhang, Yanqi Shi, Liwen Xiao

    Hydrogel materials have been used extensively in microbial electrochemical technology (MET) and sensor development due to their high biocompatibility and low toxicity. With an increasing demand for sensors across different sectors, it is crucial to understand the current state within the sectors of hydrogel METs and sensors. Surprisingly, a systematic review examining the application of hydrogel-based METs to sensor technologies has not yet been conducted. This review aimed to identify the current research progress surrounding the incorporation of hydrogels within METs and sensors development, with a specific focus on microbial fuel cells (MFCs) and microbial electrolysis cells (MECs). The manufacturing process/cost, operational performance, analysis accuracy and stability of typical hydrogel materials in METs and sensors were summarised and analysed. The current challenges facing the technology as well as potential direction for future research were also discussed. This review will substantially promote the understanding of hydrogel materials used in METs and benefit the development of electrochemical biosensors using hydrogel-based METs.


  • Open Access

    Microbe-Based Sensor for Long-Term Detection of Urine Glucose

    by Dunzhu Li, Yunhong Shi, Yifan Sun, Zeena Wang, Daniel K. Kehoe, Luis Romeral, Fei Gao, Luming Yang, David McCurtin, Yurii K. Gun’ko, et al.

    The development of a reusable and low-cost urine glucose sensor can benefit the screening and control of diabetes mellitus. This study focused on the feasibility of employing microbial fuel cells (MFC) as a selective glucose sensor for continuous monitoring of glucose levels in human urine. Using MFC technology, a novel cylinder sensor (CS) was developed. It had a quick response time (100 s), a large detection range (0.3–5 mM), and excellent accuracy. More importantly, the CS could last for up to 5 months. The selectivity of the CS was validated by both synthetic and actual diabetes-negative urine samples. It was found that the CS’s selectivity could be significantly enhanced by adjusting the concentration of the culture’s organic matter. The CS results were comparable to those of a commercial glucose meter (recovery ranged from 93.6% to 127.9%) when the diabetes-positive urine samples were tested. Due to the multiple advantages of high stability, low cost, and high sensitivity over urine test strips, the CS provides a novel and reliable approach for continuous monitoring of urine glucose, which will benefit diabetes assessment and control.