Uriah Kilgore
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Uriah Kilgore has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Michael R. Thorson
Pacific Northwest National Laboratory, 902 Battelle Blvd, Richland, WA 99352, USA
4 shared publications Andrew J. Schmidt
2 shared publications- Andrew Schmidt2 shared publications
Daniel M. Santosa
Pacific Northwest National Laboratory, 902 Battelle Blvd, Richland, WA 99352, USA
2 shared publications- Dylan John Cronin
Centre for Tropical Crops and Biocommodities, Queensland University of Technology, Brisbane, Australia
2 shared publications Emily N. Diaz
2 shared publications
Latest Publications
- Open Access
- 22 September 2026
- Published by Elsevier in SSRN Electronic Journal
Separation of Hydrothermal Liquefaction Product Emulsions by Continuous-Flow Solvent Extraction
Hydrothermal liquefaction (HTL) is a promising thermochemical technology for energy recovery from wet biomass feedstocks. The resultant biocrude products may present challenges for upgrading due to their high water, nitrogen, and inorganic content. A separation scheme which isolates the HTL-solid product (HTL-SP) from the aqueous (HTL-AQ) and biocrude while maximizing biocrude recovery from the HTL product emulsion is necessary prior to biocrude upgrading. Hence, continuous liquid slurry extraction (LSE) is explored in this study as a separation and pretreatment method to address these challenges by improving biocrude quality and recovery from aqueous and solid byproducts. Extractions performed under optimized conditions using a solvent system of 80/20 w/w toluene and heptane, demonstrated significant reductions in water content from >10% to ca. 0.5 wt% and nitrogen content (decreasing from ca. 4.5 wt% to ca. 3%). Acid-assisted extractions further reduced total metals content in the biocrude (to ca. 120 ppm). Biocrude recoveries ranged from 87–93% in single-stage acid-assisted extractions. The study also revealed that an additional 10% of biocrude could be recovered from the HTL-SP during LSE. These findings highlight LSE as an effective pretreatment strategy for improving biocrude quality, addressing key upgrading barriers while enhancing recovery and refining efficiency.
- 22 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSeparation of Hydrothermal Liquefaction Product Emulsions by Continuous-Flow Solvent Extraction
Hydrothermal liquefaction (HTL) is a promising thermochemical technology for energy recovery from wet biomass feedstocks. The resultant biocrude products may present challenges for upgrading due to their high water, nitrogen, and inorganic content. A separation scheme which isolates the HTL-solid product (HTL-SP) from the aqueous (HTL-AQ) and biocrude while maximizing biocrude recovery from the HTL product emulsion is necessary prior to biocrude upgrading. Hence, continuous liquid slurry extraction (LSE) is explored in this study as a separation and pretreatment method to address these challenges by improving biocrude quality and recovery from aqueous and solid byproducts. Extractions performed under optimized conditions using a solvent system of 80/20 w/w toluene and heptane, demonstrated significant reductions in water content from >10% to ca. 0.5 wt% and nitrogen content (decreasing from ca. 4.5 wt% to ca. 3%). Acid-assisted extractions further reduced total metals content in the biocrude (to ca. 120 ppm). Biocrude recoveries ranged from 87–93% in single-stage acid-assisted extractions. The study also revealed that an additional 10% of biocrude could be recovered from the HTL-SP during LSE. These findings highlight LSE as an effective pretreatment strategy for improving biocrude quality, addressing key upgrading barriers while enhancing recovery and refining efficiency.
- Open Access
- 14 March 2026
- Published by Elsevier in SSRN Electronic Journal
PERFORMANCE ANALYSIS OF AN ENGINEERING-SCALE HYDROTHERMAL LIQUEFACTION SYSTEM
This work evaluates the performance of the Modular Hydrothermal Liquefaction System, an engineering‐scale, integrated continuous hydrothermal liquefaction plant operated at Pacific Northwest National Laboratory, in converting realistic wet wastes into energy‐dense biocrudes. We employed production campaigns processing algae, sewage sludges, lignocellulosic blends, industrial food waste, and engineered food waste slurries at 350 °C and around 200 bar, with nominal feed rates of ~12 L h⁻¹. We report here biocrude yields and compositions, established mass and elemental (C, N) balances, and quantified energy performance via heater duties, heat‐exchanger behavior, and system‐level efficiencies. This paper also brings invaluable insights on safe operations and experimental observations gathered when operating a continuous hydrothermal liquefaction system.Biocrudes contained 76–80 wt% C (dry, ash‐free), with higher heating values of 38–41 MJ kg⁻¹, which are substantially higher than the feed material higher heating values of 16.6–26.1 MJ kg⁻¹ and are close to those of petroleum fuels. Dry, ash‐free biocrude yields of 32–53 wt% corresponded to 43–71 wt% carbon yields, with 18–40 wt% of feed carbon routed to the aqueous phase. Thermal efficiencies were 50%–65%, and total energy efficiencies, including reactor heat input, were 35%–55%. A counter‐current tube‐in‐tube heat exchanger delivered U values of 200–450 W m⁻² K⁻¹, with fouling‐induced declines affecting heat recovery and heater duty. The analysis highlights several priorities for the process intensification of hydrothermal liquefaction: robust, fouling‐resistant heat recovery; hydrodynamically suitable reactor and heat‐exchanger designs; simplified and predictable solids management; and biocrude-water separation.
- 14 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessPERFORMANCE ANALYSIS OF AN ENGINEERING-SCALE HYDROTHERMAL LIQUEFACTION SYSTEM
This work evaluates the performance of the Modular Hydrothermal Liquefaction System, an engineering‐scale, integrated continuous hydrothermal liquefaction plant operated at Pacific Northwest National Laboratory, in converting realistic wet wastes into energy‐dense biocrudes. We employed production campaigns processing algae, sewage sludges, lignocellulosic blends, industrial food waste, and engineered food waste slurries at 350 °C and around 200 bar, with nominal feed rates of ~12 L h⁻¹. We report here biocrude yields and compositions, established mass and elemental (C, N) balances, and quantified energy performance via heater duties, heat‐exchanger behavior, and system‐level efficiencies. This paper also brings invaluable insights on safe operations and experimental observations gathered when operating a continuous hydrothermal liquefaction system.Biocrudes contained 76–80 wt% C (dry, ash‐free), with higher heating values of 38–41 MJ kg⁻¹, which are substantially higher than the feed material higher heating values of 16.6–26.1 MJ kg⁻¹ and are close to those of petroleum fuels. Dry, ash‐free biocrude yields of 32–53 wt% corresponded to 43–71 wt% carbon yields, with 18–40 wt% of feed carbon routed to the aqueous phase. Thermal efficiencies were 50%–65%, and total energy efficiencies, including reactor heat input, were 35%–55%. A counter‐current tube‐in‐tube heat exchanger delivered U values of 200–450 W m⁻² K⁻¹, with fouling‐induced declines affecting heat recovery and heater duty. The analysis highlights several priorities for the process intensification of hydrothermal liquefaction: robust, fouling‐resistant heat recovery; hydrodynamically suitable reactor and heat‐exchanger designs; simplified and predictable solids management; and biocrude-water separation.
- Open Access
- 21 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Sustainability
- Vol. 4 (3) , 1356-1366
Techno-economic and life cycle assessment of wet waste hydrothermal liquefaction with different biocrude upgrading strategies
Hydrothermal liquefaction (HTL) emerges as a promising technology for producing various renewable biofuels from wet waste.
- 21 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Sustainability
- Vol. 4 (3) , 1356-1366
Open AccessTechno-economic and life cycle assessment of wet waste hydrothermal liquefaction with different biocrude upgrading strategies
Hydrothermal liquefaction (HTL) emerges as a promising technology for producing various renewable biofuels from wet waste.
- Open Access
- 19 June 2024
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 8 (15) , 3279-3289
Solvent processing for improved separation of hydrothermal liquefaction products
Hydrothermal liquefaction (HTL) is a technology capable of producing sustainable hydrocarbon fuels from wet waste, reducing volumes of that waste as an added benefit. However, sustainable fuel production through HTL has yet to reach commercial scale and opportunities for improvements to process safety remain. This work describes low-pressure, low-temperature, two-stage solvent extraction and separation of HTL products utilizing naphtha range hydrocarbons. The similar qualitative solubility behavior of bitumen and biocrude (BC) with respect to paraffin versus naphthene or aromatic solvent composition allows us to examine a process comparable to solvent processing of bitumen. Lab-scale experiments were carried out to demonstrate the basic process and evaluate key parameters. The laboratory work indicates that using aliphatic/aromatic solvent mixtures at 80 °C results in a recovery of nearly 100% of the biocrude from the product mixture with reduced carbon content on the hydro-char. The findings illustrate the potential of solvent extraction for HTL biocrude processing. On a commercial scale, such a process may de-risk HTL, improving prospects for commercialization, opening the door to widespread conversion of wet-waste and waste biomass to sustainable fuels by HTL.
- 19 June 2024
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 8 (15) , 3279-3289
Open AccessSolvent processing for improved separation of hydrothermal liquefaction products
Hydrothermal liquefaction (HTL) is a technology capable of producing sustainable hydrocarbon fuels from wet waste, reducing volumes of that waste as an added benefit. However, sustainable fuel production through HTL has yet to reach commercial scale and opportunities for improvements to process safety remain. This work describes low-pressure, low-temperature, two-stage solvent extraction and separation of HTL products utilizing naphtha range hydrocarbons. The similar qualitative solubility behavior of bitumen and biocrude (BC) with respect to paraffin versus naphthene or aromatic solvent composition allows us to examine a process comparable to solvent processing of bitumen. Lab-scale experiments were carried out to demonstrate the basic process and evaluate key parameters. The laboratory work indicates that using aliphatic/aromatic solvent mixtures at 80 °C results in a recovery of nearly 100% of the biocrude from the product mixture with reduced carbon content on the hydro-char. The findings illustrate the potential of solvent extraction for HTL biocrude processing. On a commercial scale, such a process may de-risk HTL, improving prospects for commercialization, opening the door to widespread conversion of wet-waste and waste biomass to sustainable fuels by HTL.
- Open Access
- 22 July 2023
- Published by Elsevier in Biomass and Bioenergy
- Vol. 176
Wet air oxidation of HTL aqueous waste
- 22 July 2023
- Published by Elsevier in Biomass and Bioenergy
- Vol. 176
Open AccessWet air oxidation of HTL aqueous waste
- 16 May 2023
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 7 (11) , 2670-2679
Desalting biocrude for improved downstream processing toward marine fuel application
Hydrothermal liquefaction of wet wastes (e.g., food waste and sewage sludge) offers a promising avenue for producing biocrude, but the resulting product is often contaminated with metals and water, impacting the biocrude upgrading steps to produce final fuel (e.g., jet and diesel). This study investigates the use of aqueous solutions of formic acid for desalting biocrudes and improving their quality. The results show that this approach significantly reduces both metal and water content, enabling mild hydrotreatment with reduced hydrogen consumption to further enhance the biocrude's quality. A preliminary technoeconomic analysis based on these experimental results shows that even without optimization, this washing process can yield biocrude with a minimum selling price of $1.87/GGE. Overall, our study demonstrates the potential for using dilute formic acid aqueous solutions to improve the quality of biocrudes, which can lead to more efficient and cost-effective conversion into biofuels.
- 16 May 2023
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 7 (11) , 2670-2679
Desalting biocrude for improved downstream processing toward marine fuel application
Hydrothermal liquefaction of wet wastes (e.g., food waste and sewage sludge) offers a promising avenue for producing biocrude, but the resulting product is often contaminated with metals and water, impacting the biocrude upgrading steps to produce final fuel (e.g., jet and diesel). This study investigates the use of aqueous solutions of formic acid for desalting biocrudes and improving their quality. The results show that this approach significantly reduces both metal and water content, enabling mild hydrotreatment with reduced hydrogen consumption to further enhance the biocrude's quality. A preliminary technoeconomic analysis based on these experimental results shows that even without optimization, this washing process can yield biocrude with a minimum selling price of $1.87/GGE. Overall, our study demonstrates the potential for using dilute formic acid aqueous solutions to improve the quality of biocrudes, which can lead to more efficient and cost-effective conversion into biofuels.