Aurelien Perigaud
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aurelien Perigaud has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Nicolas Delhote
Université de Limoges
4 shared publications - Stephane Bila
University of Limoges, CNRS, XLIM UMR 7252, Limoges, France
3 shared publications Serge Verdeyme
XLIM Laboratory, UMR 7252, University of Limoges, Limoges, France
2 shared publications- Alejandro Pons-Abenza
Department of Electrical, Electronic and Communications Engineering Institute of Smart Cities (ISC) Public University of Navarre (UPNA) Pamplona España
1 shared publication - Andrés Fontana
Tyndall National Institute, Cork, Ireland
1 shared publication Anthony Delage
XLIM Laboratory, UMR 7252, University of Limoges, Limoges, France
1 shared publication
Latest Publications
- Open Access
- 12 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (12) , 1913-1916
Rigorous Design of Compact High-Performance 3-D Microstrip Filters Using Inverse Scattering
In this letter, a novel design method for 3-D microstrip filters is proposed. The method is valid for any all-pole transfer function and employs an inverse scattering synthesis technique to generate a smooth characteristic impedance profile that is implemented by smoothly varying the substrate height and strip width. In this way, strongly enhanced characteristic impedance excursions can be implemented, allowing us to synthesize filters with very wide rejection bands and very compact physical dimensions. As an example of application, a Ku-band low-pass filter (LPF) with cut-off frequency of 11.8 GHz and rejection band up to 36 GHz is designed, featuring a length of 10.66 mm. The filter is fabricated through additive manufacturing (AM) and the measurements obtained confirm its excellent performance.
- 12 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (12) , 1913-1916
Open AccessRigorous Design of Compact High-Performance 3-D Microstrip Filters Using Inverse Scattering
In this letter, a novel design method for 3-D microstrip filters is proposed. The method is valid for any all-pole transfer function and employs an inverse scattering synthesis technique to generate a smooth characteristic impedance profile that is implemented by smoothly varying the substrate height and strip width. In this way, strongly enhanced characteristic impedance excursions can be implemented, allowing us to synthesize filters with very wide rejection bands and very compact physical dimensions. As an example of application, a Ku-band low-pass filter (LPF) with cut-off frequency of 11.8 GHz and rejection band up to 36 GHz is designed, featuring a length of 10.66 mm. The filter is fabricated through additive manufacturing (AM) and the measurements obtained confirm its excellent performance.
- 16 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (9) , 3915-3928
A Novel Approach Toward the Integration of Fully 3-D Printed Surface-Mounted Microwave Ceramic Filters
A first approach toward the integration of heterogeneous electronic circuit technologies and fully 3-D printed ceramic microwave devices is discussed in this work. Additive manufacturing (AM) capabilities are explored for the development of multifunction surface-mount compact components used in different RF front-ends’ scenarios. Monolithic ceramic bandpass filters (BPFs) are designed to operate in the $X$ -Band and to assess the typical limitations of ceramic stereolithography (SLA) processes. A post-fabrication tuning method based on a laser engraving strategy is presented to overcome the manufacturing constraints and carry out the filters’ correction. 2.5-D and 3-D printed four-pole filters were fabricated and tuned using the proposed methodology.
- 16 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (9) , 3915-3928
A Novel Approach Toward the Integration of Fully 3-D Printed Surface-Mounted Microwave Ceramic Filters
A first approach toward the integration of heterogeneous electronic circuit technologies and fully 3-D printed ceramic microwave devices is discussed in this work. Additive manufacturing (AM) capabilities are explored for the development of multifunction surface-mount compact components used in different RF front-ends’ scenarios. Monolithic ceramic bandpass filters (BPFs) are designed to operate in the $X$ -Band and to assess the typical limitations of ceramic stereolithography (SLA) processes. A post-fabrication tuning method based on a laser engraving strategy is presented to overcome the manufacturing constraints and carry out the filters’ correction. 2.5-D and 3-D printed four-pole filters were fabricated and tuned using the proposed methodology.
- 25 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A new dual RF sensor in gas detection and humidity influence
In this paper, we propose to study the influence of moisture on passive radiofrequency (RF) sensors associated with poly (3,4-ethylenedioxythiophene) polystyrene sulfonate -multi walled carbon nanotubes (PEDOT:PSS-MWCNT) as a sensitive material. The designed sensor consists of a copper ring resonator and two PEDOT:PSS-MWCNT stubs located in the maximum electric fields of the fundamental resonant mode operating at 3.94 GHz. For performing a differential analysis, experiments are conducted by considering the resonant structure with and without a sensitive layer. Our experiments show the high interference of humidity on the sensor’s performances and highlight the importance of differential study to decorrelate physical and chemical surrounding parameters. This differential innovative structure paves the way for a very high sensitive passive RF sensor dedicated for gas sensing.
- 25 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A new dual RF sensor in gas detection and humidity influence
In this paper, we propose to study the influence of moisture on passive radiofrequency (RF) sensors associated with poly (3,4-ethylenedioxythiophene) polystyrene sulfonate -multi walled carbon nanotubes (PEDOT:PSS-MWCNT) as a sensitive material. The designed sensor consists of a copper ring resonator and two PEDOT:PSS-MWCNT stubs located in the maximum electric fields of the fundamental resonant mode operating at 3.94 GHz. For performing a differential analysis, experiments are conducted by considering the resonant structure with and without a sensitive layer. Our experiments show the high interference of humidity on the sensor’s performances and highlight the importance of differential study to decorrelate physical and chemical surrounding parameters. This differential innovative structure paves the way for a very high sensitive passive RF sensor dedicated for gas sensing.
- 16 April 2018
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 10 (7) , 772-782
Plastic and metal additive manufacturing technologies for microwave passive components up toKaband
This paper illustrates the different possibilities given by additive manufacturing technologies for the creation of passive microwave hardware. The paper more specifically highlights a prototyping scheme where the 3D-printed plastic parts can be used as initial proofs of concept before considering more advanced 3D-printed parts (metal parts, for instance). First, a characterization campaign has been made on common plastics used by a 3D printer using the fused deposition modeling and material jetting (Polyjet©) technologies. The impact of the manufacturing strategy (high-speed or high-accuracy) on the part roughness, as well as on the dielectric material permittivity and loss tangent, has been specifically studied at 10 and 16 GHz. Based on a specifically optimized and deeply explained characterization method, the conductivity of a coating based on silver paint has also been characterized on such plastic parts at 10 and 40 GHz. These plastic materials and coating have been used for the creation of quasi-elliptic and tuning-free bandpass filters centered at 6 and 12 GHz and compared with a similar filter made of stainless steel by selective laser melting. Finally, a compact rectangular TE 10 to circular TE 01 mode converter also undergoes one prototyping step out of plastic before moving to an advanced part made out of stainless steel. This mode converter, which is made in a single part, is designed to operate from 28 to 36 GHz as a tuning-free final demonstrator.
- 16 April 2018
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 10 (7) , 772-782
Plastic and metal additive manufacturing technologies for microwave passive components up toKaband
This paper illustrates the different possibilities given by additive manufacturing technologies for the creation of passive microwave hardware. The paper more specifically highlights a prototyping scheme where the 3D-printed plastic parts can be used as initial proofs of concept before considering more advanced 3D-printed parts (metal parts, for instance). First, a characterization campaign has been made on common plastics used by a 3D printer using the fused deposition modeling and material jetting (Polyjet©) technologies. The impact of the manufacturing strategy (high-speed or high-accuracy) on the part roughness, as well as on the dielectric material permittivity and loss tangent, has been specifically studied at 10 and 16 GHz. Based on a specifically optimized and deeply explained characterization method, the conductivity of a coating based on silver paint has also been characterized on such plastic parts at 10 and 40 GHz. These plastic materials and coating have been used for the creation of quasi-elliptic and tuning-free bandpass filters centered at 6 and 12 GHz and compared with a similar filter made of stainless steel by selective laser melting. Finally, a compact rectangular TE 10 to circular TE 01 mode converter also undergoes one prototyping step out of plastic before moving to an advanced part made out of stainless steel. This mode converter, which is made in a single part, is designed to operate from 28 to 36 GHz as a tuning-free final demonstrator.
- Open Access
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Optimized synthesis of a microwave equalizer for matching a high performance small antenna
A dual-band RHCP (right-hand circular polarization) microstrip patch antenna is presented for its implementation on a GNSS receiver covering the bands L2, E6 and L1. To improve the total efficiency at the band edges, a dualband equalized is designed by implementing a dual-band filter matched to the complex impedance of the antenna. This filter is composed of two single-band filters, each of them designed to maximize the minimum efficiency in the correspondent band, connected together with input and output junctions. Moreover a microstrip prototype for the dual-band equalizer is designed and fullwave simulations show the equalized efficiency validating the theoretical results.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Open AccessOptimized synthesis of a microwave equalizer for matching a high performance small antenna
A dual-band RHCP (right-hand circular polarization) microstrip patch antenna is presented for its implementation on a GNSS receiver covering the bands L2, E6 and L1. To improve the total efficiency at the band edges, a dualband equalized is designed by implementing a dual-band filter matched to the complex impedance of the antenna. This filter is composed of two single-band filters, each of them designed to maximize the minimum efficiency in the correspondent band, connected together with input and output junctions. Moreover a microstrip prototype for the dual-band equalizer is designed and fullwave simulations show the equalized efficiency validating the theoretical results.