Jixin Xiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jixin Xiang has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Zhiqiang Li
Shanxi Key Laboratory of Material Strength & Structural Impact, Taiyuan University of Technology, Taiyuan 030024, China
2 shared publications - Bohan He
College of Aeronautics and Astronautics, Taiyuan University of Technology, Taiyuan 030024, China
1 shared publication - Hairun Xie
Key Laboratory for Satellite Digitalization Technology, Innovation Academy for Microsatellites of CAS, Shanghai, China
1 shared publication - He Ren
College of Aeronautics and Astronautics, Taiyuan University of Technology, Taiyuan 030600, China
1 shared publication - Jing Wang
School of Aeronautics and Astronautics, Shanghai Jiao Tong University, Shanghai, China
1 shared publication - Miao Zhang
Shanghai Aircraft Design and Research Institute, Shanghai, China
1 shared publication
Latest Publications
- Open Access
Effects of Different Structural Film Cooling on Cooling Performance in a GO2/GH2 Subscale Thrust Chamber
To investigate the wall cooling of the thrust chamber in an engine, two film-cooling structures, namely, a circular hole structure and a slot structure, were designed. Numerical simulations were performed to study the coupled flow and regenerative cooling heat transfer in thrust chambers with different structures. The influences of parameters such as the film mass flow rate and film hole size on wall cooling were analyzed. Experiments were conducted in a thrust chamber to validate the accuracy of the numerical calculation method. The results indicate that the slot-structured film adheres better to the wall than the circular-hole-structured film, and the film closely adhering to the wall provides better insulation against hot gas, resulting in a reduction of approximately 6% in wall temperature. When the film hole size changes, the change in circumferential wall temperature in the upstream region of the slot-structured film is more pronounced. This paper aims to provide a reference for the design of the cooling structure at the head of the thrust chamber in engineering and suggests directions for optimization and improvement.
Open AccessEffects of Different Structural Film Cooling on Cooling Performance in a GO2/GH2 Subscale Thrust Chamber
To investigate the wall cooling of the thrust chamber in an engine, two film-cooling structures, namely, a circular hole structure and a slot structure, were designed. Numerical simulations were performed to study the coupled flow and regenerative cooling heat transfer in thrust chambers with different structures. The influences of parameters such as the film mass flow rate and film hole size on wall cooling were analyzed. Experiments were conducted in a thrust chamber to validate the accuracy of the numerical calculation method. The results indicate that the slot-structured film adheres better to the wall than the circular-hole-structured film, and the film closely adhering to the wall provides better insulation against hot gas, resulting in a reduction of approximately 6% in wall temperature. When the film hole size changes, the change in circumferential wall temperature in the upstream region of the slot-structured film is more pronounced. This paper aims to provide a reference for the design of the cooling structure at the head of the thrust chamber in engineering and suggests directions for optimization and improvement.
- 26 March 2024
- Published by Springer Nature in Journal of Membrane Computing
- Vol. 6 (2) , 53-66
Uncertainty involved drag divergence characteristic predicting method based on VAE
- 26 March 2024
- Published by Springer Nature in Journal of Membrane Computing
- Vol. 6 (2) , 53-66
Uncertainty involved drag divergence characteristic predicting method based on VAE
- Open Access
Buckling Analysis and Structure Improvement for the Afterburner Cylinder of an Aero-Engine
The buckling failure of the afterburner cylinder is a serious safety concern for aero-engines. To tackle this issue, the buckling simulation analysis of the afterburner cylinder was carried out by using finite element method (FEM) software to obtain the buckling mode and critical buckling loads. It was found that the afterburner cylinder was susceptible to buckling when subjected to differential pressure or the compressive force of the rear flange. Buckling would occur when the differential pressure reached 0.4 times the atmospheric pressure or when the axial compressive force on the rear flange reached 222.8 kN. Buckling was also found at the front of the cylinder under the auxiliary mount load. Additionally, under various loads on the rear flange, buckling occurred in the rear section, with the buckling mode being closely related to the load characteristics. Based on the simulation results and structural design requirements, two structural improvements were proposed, including the wall-thickening scheme and the grid reinforcement scheme. FEM simulation analysis results showed that both schemes would improve the rigidity and stability of the afterburner cylinder. For the 0.3 mm increase in the wall thickness scheme, the critical buckling load increased by 17.86% to 66.4%; for the grid reinforcement scheme, the critical buckling load increased by 169% to 619%. Therefore, the grid reinforcement scheme had a stronger anti-buckling ability and was deemed the optimal solution. The findings of this paper could provide technical support for the structural design of large-sized and thin-walled components of aero-engines.
Open AccessBuckling Analysis and Structure Improvement for the Afterburner Cylinder of an Aero-Engine
The buckling failure of the afterburner cylinder is a serious safety concern for aero-engines. To tackle this issue, the buckling simulation analysis of the afterburner cylinder was carried out by using finite element method (FEM) software to obtain the buckling mode and critical buckling loads. It was found that the afterburner cylinder was susceptible to buckling when subjected to differential pressure or the compressive force of the rear flange. Buckling would occur when the differential pressure reached 0.4 times the atmospheric pressure or when the axial compressive force on the rear flange reached 222.8 kN. Buckling was also found at the front of the cylinder under the auxiliary mount load. Additionally, under various loads on the rear flange, buckling occurred in the rear section, with the buckling mode being closely related to the load characteristics. Based on the simulation results and structural design requirements, two structural improvements were proposed, including the wall-thickening scheme and the grid reinforcement scheme. FEM simulation analysis results showed that both schemes would improve the rigidity and stability of the afterburner cylinder. For the 0.3 mm increase in the wall thickness scheme, the critical buckling load increased by 17.86% to 66.4%; for the grid reinforcement scheme, the critical buckling load increased by 169% to 619%. Therefore, the grid reinforcement scheme had a stronger anti-buckling ability and was deemed the optimal solution. The findings of this paper could provide technical support for the structural design of large-sized and thin-walled components of aero-engines.