Minghua Jing
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Minghua Jing has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Dawei Fang
Institute of Rare and Scattered Elements, College of Chemistry, Liaoning University, Shenyang, Liaoning 110036, China
6 shared publications Qian Gao
Liaoning University
3 shared publicationsAng Zhang
2 shared publicationsDawei Fang
2 shared publicationsHao Yu
College of Environment
2 shared publicationsJie Yang
Liaoning University
2 shared publications
Latest Publications
- 26 October 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (44) , 20549-20562
Highly Conductive Carbon Nanosheets Derived from Rhodanine Pyrolysis-Modified Graphite Felt for Viologen-Based Redox Flow Batteries
Viologen-based aqueous organic redox flow batteries (AORFBs) are characterized by outstanding electrochemical reactivity. Simultaneously improving the electrical conductivity of electrode materials while maintaining sufficient active surface area is recognized as a viable strategy to enhance the energy conversion efficiency of AORFBs. In this study, graphite felt (GF) was selected as the electrode substrate, and ultrathin carbon nanosheets were synthesized via in situ growth on the surface of graphite felt fibers through in situ pyrolysis of rhodanine, which enables synergistic improvement of the electrical conductivity and electrochemically active area of the resulting electrode. The loading mass of rhodanine was systematically optimized, and the surface chemical composition, microstructure, physicochemical properties, and electrochemical performance of the as-prepared materials were comprehensively characterized. Experimental results demonstrated that the RGF-0.75%-T10 composite electrode exhibits the optimal electrochemical activity toward viologen molecules. A BTMAP-vi/Nme-TEMPO flow cell was assembled to evaluate the practical application potential of the prepared electrodes. In comparison with the battery assembled with pristine graphite felt electrodes, the device constructed with RGF-0.75%-T10 electrodes delivers a substantially reduced charge–discharge overpotential. At a current density of 80 mA cm–2, the voltage efficiency and energy efficiency of the proposed battery reach 80.11% and 79.06% respectively, which are 12.16% and 13.12% higher than those of the pristine graphite felt-based battery. Meanwhile, the peak power density of the assembled battery reaches 113 mW cm–2, which is substantially higher than the 82 mW cm–2 of the battery employing unmodified graphite felt electrodes. This work confirms that constructing electrodes with high electrical conductivity and large active surface area is an effective approach to improve the comprehensive performance of viologen-based aqueous organic redox flow batteries.
- 26 October 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (44) , 20549-20562
Highly Conductive Carbon Nanosheets Derived from Rhodanine Pyrolysis-Modified Graphite Felt for Viologen-Based Redox Flow Batteries
Viologen-based aqueous organic redox flow batteries (AORFBs) are characterized by outstanding electrochemical reactivity. Simultaneously improving the electrical conductivity of electrode materials while maintaining sufficient active surface area is recognized as a viable strategy to enhance the energy conversion efficiency of AORFBs. In this study, graphite felt (GF) was selected as the electrode substrate, and ultrathin carbon nanosheets were synthesized via in situ growth on the surface of graphite felt fibers through in situ pyrolysis of rhodanine, which enables synergistic improvement of the electrical conductivity and electrochemically active area of the resulting electrode. The loading mass of rhodanine was systematically optimized, and the surface chemical composition, microstructure, physicochemical properties, and electrochemical performance of the as-prepared materials were comprehensively characterized. Experimental results demonstrated that the RGF-0.75%-T10 composite electrode exhibits the optimal electrochemical activity toward viologen molecules. A BTMAP-vi/Nme-TEMPO flow cell was assembled to evaluate the practical application potential of the prepared electrodes. In comparison with the battery assembled with pristine graphite felt electrodes, the device constructed with RGF-0.75%-T10 electrodes delivers a substantially reduced charge–discharge overpotential. At a current density of 80 mA cm–2, the voltage efficiency and energy efficiency of the proposed battery reach 80.11% and 79.06% respectively, which are 12.16% and 13.12% higher than those of the pristine graphite felt-based battery. Meanwhile, the peak power density of the assembled battery reaches 113 mW cm–2, which is substantially higher than the 82 mW cm–2 of the battery employing unmodified graphite felt electrodes. This work confirms that constructing electrodes with high electrical conductivity and large active surface area is an effective approach to improve the comprehensive performance of viologen-based aqueous organic redox flow batteries.
- 15 April 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (16) , 7704-7714
Dual-Functional Hydroxyethylidene Diphosphate Additive for Broadening the Operating Temperature Range and Optimizing the Reaction Kinetics of Electrolyte in Vanadium Redox Flow Battery
- 15 April 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (16) , 7704-7714
Dual-Functional Hydroxyethylidene Diphosphate Additive for Broadening the Operating Temperature Range and Optimizing the Reaction Kinetics of Electrolyte in Vanadium Redox Flow Battery
- 11 May 2024
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 404
Physicochemical and electrochemical properties of several readily available anthraquinone aqueous electrolytes
- 11 May 2024
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 404
Physicochemical and electrochemical properties of several readily available anthraquinone aqueous electrolytes
- Open Access
Readily Accessible M-Ferrocenyl-Phenyl Sulfonate as Novel Cathodic Electrolyte for Aqueous Organic Redox Flow Batteries
Ferrocene derivatives are amongst the most promising electroactive organic electrolytes. The bottleneck problems of their application in aqueous redox flow batteries are their poor solubility and lower potential as well as the complexity of the modification methods to solve these problems. In this study, a benzenesulfonic acid group is easily introduced into the ferrocene structure by a mature diazotization reaction, and the synthesized sodium m-phenylferrocene sulfonate BASFc is used as the novel cathodic electroactive electrolyte for AORFB. The hydrophilicity and the electron-absorbing effect of the introduced benzenesulfonic group can effectively improve the water solubility and redox potential of ferrocene. Moreover, the introduction of phenyl extends the conjugated structure of ferrocene and increases its structural dimension, which may be conducive to reducing its membrane permeability and improving the structural stability to some extent. The physical structure and the electrochemical properties of BASFc are studied systematically; the feasibility of its application as a cathodic electrolyte in AORFBs is verified by assembling the half-cell and full-cell. The results verify the good electrochemical reaction kinetics of BASFc in acid electrolyte and the corresponding AORFB shows satisfactory efficiency and stability.
Open AccessReadily Accessible M-Ferrocenyl-Phenyl Sulfonate as Novel Cathodic Electrolyte for Aqueous Organic Redox Flow Batteries
Ferrocene derivatives are amongst the most promising electroactive organic electrolytes. The bottleneck problems of their application in aqueous redox flow batteries are their poor solubility and lower potential as well as the complexity of the modification methods to solve these problems. In this study, a benzenesulfonic acid group is easily introduced into the ferrocene structure by a mature diazotization reaction, and the synthesized sodium m-phenylferrocene sulfonate BASFc is used as the novel cathodic electroactive electrolyte for AORFB. The hydrophilicity and the electron-absorbing effect of the introduced benzenesulfonic group can effectively improve the water solubility and redox potential of ferrocene. Moreover, the introduction of phenyl extends the conjugated structure of ferrocene and increases its structural dimension, which may be conducive to reducing its membrane permeability and improving the structural stability to some extent. The physical structure and the electrochemical properties of BASFc are studied systematically; the feasibility of its application as a cathodic electrolyte in AORFBs is verified by assembling the half-cell and full-cell. The results verify the good electrochemical reaction kinetics of BASFc in acid electrolyte and the corresponding AORFB shows satisfactory efficiency and stability.
- 1 March 2022
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 169 (3) , 030545
Communication—A Universal Approach for Constructing Functionalized Porous Graphene Gelatum/Graphite Bipolar Plate Integrated Electrode for Vanadium Redox Flow Batteries
We investigated the mismatched kinetics of electrode reactions in VRFB, RuO 2, and Bi nanoparticles as the functional components electrodeposited on graphene porous gelatum-graphite bipolar plate (ERGO-GBP) integrated electrode and serving as anode and cathode, respectively. Benefitting from the unique structure and specific functionality, the novel integrated electrodes exhibit excellent electrochemical properties and functionality. The asymmetric VRFB with an RuO 2 -ERGO-GBP anode and a Bi-ERGO-GBP cathode shows better performance compared to the symmetric VRFB with ERGO-GBP as both anode and cathode, suggesting a feasible strategy to construct asymmetric VRFB with various functionalized ERGO-GBP integrated electrodes.
- 1 March 2022
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 169 (3) , 030545
Communication—A Universal Approach for Constructing Functionalized Porous Graphene Gelatum/Graphite Bipolar Plate Integrated Electrode for Vanadium Redox Flow Batteries
We investigated the mismatched kinetics of electrode reactions in VRFB, RuO 2, and Bi nanoparticles as the functional components electrodeposited on graphene porous gelatum-graphite bipolar plate (ERGO-GBP) integrated electrode and serving as anode and cathode, respectively. Benefitting from the unique structure and specific functionality, the novel integrated electrodes exhibit excellent electrochemical properties and functionality. The asymmetric VRFB with an RuO 2 -ERGO-GBP anode and a Bi-ERGO-GBP cathode shows better performance compared to the symmetric VRFB with ERGO-GBP as both anode and cathode, suggesting a feasible strategy to construct asymmetric VRFB with various functionalized ERGO-GBP integrated electrodes.
- 1 March 2022
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 169 (3) , 030501
Green and Affordable Manufacturing Method for Multi-Scale Porous Carbon Nanofibers and Its Application in Vanadium Redox Flow Battery
Carbon nanofibers with multi-scale pores have been easily constructed by synchronous water etching during the carbonization process of PAN nanofibers, reducing the additional consumption of energy and time. After etching by high-temperature water vapor, the fiber surface becomes more coarse, and large amounts of etched pits are formed, effectively increasing the electrode’s specific surface area and hydrophilicity. Oxygen content is also significantly increased, which may effectively increase the electrocatalytic active sites of the electrode. Electrochemical tests verified the improved electrocatalytic activity and increased effective surface area. As a result, the VRFB single cell with water vapor etched carbon nanofibers as its electrode shows higher battery efficiencies than that with pristine carbon nanofibers; the energy efficiency improves by nearly 9.4% at 200 mA·cm −2 . After 100 charge/discharge cycles, the battery efficiency has no obvious attenuation, and the capacity attenuation rate of single cycle is nearly 0.26%,suggesting a satisfactory cycling stability. This green and simple method for constructing multi-scale porous carbon nanofibers electrode is expected to achieve large-scale production of high-performance electrode materials, and can be applied in various electrochemical energy storage systems.
- 1 March 2022
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 169 (3) , 030501
Green and Affordable Manufacturing Method for Multi-Scale Porous Carbon Nanofibers and Its Application in Vanadium Redox Flow Battery
Carbon nanofibers with multi-scale pores have been easily constructed by synchronous water etching during the carbonization process of PAN nanofibers, reducing the additional consumption of energy and time. After etching by high-temperature water vapor, the fiber surface becomes more coarse, and large amounts of etched pits are formed, effectively increasing the electrode’s specific surface area and hydrophilicity. Oxygen content is also significantly increased, which may effectively increase the electrocatalytic active sites of the electrode. Electrochemical tests verified the improved electrocatalytic activity and increased effective surface area. As a result, the VRFB single cell with water vapor etched carbon nanofibers as its electrode shows higher battery efficiencies than that with pristine carbon nanofibers; the energy efficiency improves by nearly 9.4% at 200 mA·cm −2 . After 100 charge/discharge cycles, the battery efficiency has no obvious attenuation, and the capacity attenuation rate of single cycle is nearly 0.26%,suggesting a satisfactory cycling stability. This green and simple method for constructing multi-scale porous carbon nanofibers electrode is expected to achieve large-scale production of high-performance electrode materials, and can be applied in various electrochemical energy storage systems.