Bassam Samy Abdel-Mageed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Bassam Samy Abdel-Mageed has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Pragasen Pillay
Department of Electrical and Computer Engineering, Concordia University, Montreal, QC, Canada
6 shared publications - Akrem Mohamed Aljehaimi
Department of Electrical and Computer Engineering, Concordia University, Montreal, Canada
4 shared publications - Fabrice Bernier
National Research Council of Canada, Boucherville, QC, Canada
1 shared publication - Jaydeep Bhalala
Noreast Electronics, Hawkesbury, ON, Canada
1 shared publication Jean-Michel Lamarre
National Research Council of Canada, Boucherville, QC, Canada
1 shared publicationMaged Ibrahim
German International University, Cairo Governorate, Egypt
1 shared publication
Latest Publications
- 31 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 62 (1) , 939-955
Analysis of Design Topologies for Variable Flux Permanent Magnet Motors
This article presents a comprehensive analysis and evaluation of four topologies for variable flux motors (VFMs) employing AlNiCo permanent magnets (PMs) on their rotors. The investigated topologies are featured with different torque capabilities such as normal saliency, inverted saliency, reluctance torque dominated, and magnet torque dominated. Three rotors employ solely AlNiCo as the PM material while the fourth rotor adopts a combination of AlNiCo and rare-earth magnets connected in series. A new procedure is proposed for evaluating and analyzing VFMs. This procedure considers the irreversible demagnetization performance of hybrid-PM VFMs and determines their safe and critical demagnetization currents. Initially, design maps are created for relating magnet dimensions with key performance metrics of the VFMs under study. Then, a detailed electromagnetic performance evaluation is conducted describing the magnetization-state-dependent operation of the four rotors. It is revealed that, full reliance upon AlNiCo magnets lead to sacrificing the reluctance torque capability of the inverted saliency VFMs. In addition, as the reluctance torque proportion is increased, the on-load demagnetization risks increase along with increasing the magnetization requirements. On the other hand, positioning the PMs magnetically in series can reduce these drawbacks with the main tradeoff being the increased risk of rareearth magnet irreversible demagnetization. Finally, experimental tests are conducted on two different motors for validating the analysis.
- 31 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 62 (1) , 939-955
Analysis of Design Topologies for Variable Flux Permanent Magnet Motors
This article presents a comprehensive analysis and evaluation of four topologies for variable flux motors (VFMs) employing AlNiCo permanent magnets (PMs) on their rotors. The investigated topologies are featured with different torque capabilities such as normal saliency, inverted saliency, reluctance torque dominated, and magnet torque dominated. Three rotors employ solely AlNiCo as the PM material while the fourth rotor adopts a combination of AlNiCo and rare-earth magnets connected in series. A new procedure is proposed for evaluating and analyzing VFMs. This procedure considers the irreversible demagnetization performance of hybrid-PM VFMs and determines their safe and critical demagnetization currents. Initially, design maps are created for relating magnet dimensions with key performance metrics of the VFMs under study. Then, a detailed electromagnetic performance evaluation is conducted describing the magnetization-state-dependent operation of the four rotors. It is revealed that, full reliance upon AlNiCo magnets lead to sacrificing the reluctance torque capability of the inverted saliency VFMs. In addition, as the reluctance torque proportion is increased, the on-load demagnetization risks increase along with increasing the magnetization requirements. On the other hand, positioning the PMs magnetically in series can reduce these drawbacks with the main tradeoff being the increased risk of rareearth magnet irreversible demagnetization. Finally, experimental tests are conducted on two different motors for validating the analysis.
- 27 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (4) , 6747-6764
Comparison Between a Series-Hybrid Variable-Flux Memory Motor and a Rare-Earth IPMSM
This paper compares a series-hybrid variable-flux memory motor with an equivalent optimized conventional rareearth IPMSM for electric vehicle applications. Hybrid variableflux motor technology with different magnetic circuit arrangements, such as series, parallel, and series-parallel, have been recently investigated for traction applications. The serieshybrid variable-flux motors (SHVFMs) have shown superiority for high torque and load demagnetization withstand capabilities. Yet, the literature lacks a detailed comparison between this evolving technology and the conventional IPMSMs for traction applications. Thus, this paper compares the two comprehensively, based on Finite Element (FE) Analysis supported by experimental results. The segregated power loss, efficiency, and power factor comparison is carried out for heavy and continuous load operation in the constant torque and field-weakening regions. It was found that for heavy load operations, the conventional IPMSM outperforms the SHVFM; however, the opposite is true for continuous load operations, significantly beyond the base speed. The magnet size/cost and inverter size are also discussed
- 27 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (4) , 6747-6764
Comparison Between a Series-Hybrid Variable-Flux Memory Motor and a Rare-Earth IPMSM
This paper compares a series-hybrid variable-flux memory motor with an equivalent optimized conventional rareearth IPMSM for electric vehicle applications. Hybrid variableflux motor technology with different magnetic circuit arrangements, such as series, parallel, and series-parallel, have been recently investigated for traction applications. The serieshybrid variable-flux motors (SHVFMs) have shown superiority for high torque and load demagnetization withstand capabilities. Yet, the literature lacks a detailed comparison between this evolving technology and the conventional IPMSMs for traction applications. Thus, this paper compares the two comprehensively, based on Finite Element (FE) Analysis supported by experimental results. The segregated power loss, efficiency, and power factor comparison is carried out for heavy and continuous load operation in the constant torque and field-weakening regions. It was found that for heavy load operations, the conventional IPMSM outperforms the SHVFM; however, the opposite is true for continuous load operations, significantly beyond the base speed. The magnet size/cost and inverter size are also discussed
- 11 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (3) , 3737-3752
Impact of Soft Magnetic Composite Materials for Traction Applications
This paper focuses on analyzing the impact of the magnetic properties of Soft Magnetic Composites (SMC) on the performance of electric motors for traction applications. A sensitivity analysis is done to select the parameters for the SMC stator. This paper presents a comparison of the SMC stator with a laminated stator design which is designed to fit into the same frame. The core loss of an SMC material is tested using a toroidal measurement setup. State-of-the-art Honda Accord motor is benchmarked with laminated and SMC stator to prove the advantages of SMC material at higher frequencies. Three different SMC materials are compared for the same machine specification. Eddy current loss density is plotted using 3D FEA analysis for all three different materials. Efficiency maps are presented for the three designs for a maximum speed range of 10000 rpm. Higher pole designs such as 24-slot/16-pole and 36-slot/30-pole has been designed and analyzed with laminated stator and SMC stator design to prove the effectiveness of the SMC material at elevated frequencies. The SMC stator is designed with a 3D flux carrying capability to improve the torque density by eliminating the end winding. The tooth body length of SMC stator is varied from 36 mm to 56 mm to analyze the performance of the motor. Nodal force and mechanical stress is calculated for the final SMC stator design with and without fillet. The manufacturing steps of the SMC stator is presented for the final design. Finally, the experimental results are presented with FEA results for the SMC motor.
- 11 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (3) , 3737-3752
Impact of Soft Magnetic Composite Materials for Traction Applications
This paper focuses on analyzing the impact of the magnetic properties of Soft Magnetic Composites (SMC) on the performance of electric motors for traction applications. A sensitivity analysis is done to select the parameters for the SMC stator. This paper presents a comparison of the SMC stator with a laminated stator design which is designed to fit into the same frame. The core loss of an SMC material is tested using a toroidal measurement setup. State-of-the-art Honda Accord motor is benchmarked with laminated and SMC stator to prove the advantages of SMC material at higher frequencies. Three different SMC materials are compared for the same machine specification. Eddy current loss density is plotted using 3D FEA analysis for all three different materials. Efficiency maps are presented for the three designs for a maximum speed range of 10000 rpm. Higher pole designs such as 24-slot/16-pole and 36-slot/30-pole has been designed and analyzed with laminated stator and SMC stator design to prove the effectiveness of the SMC material at elevated frequencies. The SMC stator is designed with a 3D flux carrying capability to improve the torque density by eliminating the end winding. The tooth body length of SMC stator is varied from 36 mm to 56 mm to analyze the performance of the motor. Nodal force and mechanical stress is calculated for the final SMC stator design with and without fillet. The manufacturing steps of the SMC stator is presented for the final design. Finally, the experimental results are presented with FEA results for the SMC motor.
- 11 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (3) , 4214-4225
Impact of Memory Motors on an IGBT-Based Inverter Efficiency
This paper investigates the impact of hybrid memory motors on an IGBT-based inverter in the field-weakening region. Hybrid variable-flux motors have been introduced to overcome the limitations of conventional IPMSMs in traction applications. Different memory motor topologies have been introduced and compared in the literature. Yet, their impact on the drive inverter has not been reported. An existing prototyped ten-horsepower series-hybrid variable motor has been used as a case study in this paper. In the field weakening region, comparing the operation with partially demagnetized magnets to fully magnetized magnets, it is found that not only does the motor current decrease, but the motor power factor also improves. This unique finding of improved power factor operation positively impacts the inverter conduction loss. This has significant practical implications, suggesting that hybrid memory motors can lead to more efficient traction inverters. An air-cooled IGBT-based three-phase 750 VDC, 30 ARMS, is used in this study. In the simulation, the switch characteristics from the datasheet have been used for loss calculations. Also, the inverter power loss and efficiency have been measured at different speeds, loads, and magnetization states. A two to three percent improvement in inverter efficiency was noted in the high-speed region beyond two per unit speed.
- 11 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (3) , 4214-4225
Impact of Memory Motors on an IGBT-Based Inverter Efficiency
This paper investigates the impact of hybrid memory motors on an IGBT-based inverter in the field-weakening region. Hybrid variable-flux motors have been introduced to overcome the limitations of conventional IPMSMs in traction applications. Different memory motor topologies have been introduced and compared in the literature. Yet, their impact on the drive inverter has not been reported. An existing prototyped ten-horsepower series-hybrid variable motor has been used as a case study in this paper. In the field weakening region, comparing the operation with partially demagnetized magnets to fully magnetized magnets, it is found that not only does the motor current decrease, but the motor power factor also improves. This unique finding of improved power factor operation positively impacts the inverter conduction loss. This has significant practical implications, suggesting that hybrid memory motors can lead to more efficient traction inverters. An air-cooled IGBT-based three-phase 750 VDC, 30 ARMS, is used in this study. In the simulation, the switch characteristics from the datasheet have been used for loss calculations. Also, the inverter power loss and efficiency have been measured at different speeds, loads, and magnetization states. A two to three percent improvement in inverter efficiency was noted in the high-speed region beyond two per unit speed.
- 6 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 40 (1) , 490-504
Modeling and Remedies for Rare-Earth Permanent Magnet Demagnetization Effects in Hybrid Permanent Magnet Variable Flux Motors
Variable-flux motors (VFMs) with hybrid permanent magnets (PMs) can limit the utilization of rare-earth PMs and reduce the high-speed losses of traction motors. These motors are often characterized by two main magnetization states (MS), i.e., the maximum and minimum. The flux variation is achieved by applying current pulses. This can be multiples of the rated current and changes the rare-earth PM operating point so that a minimum flux is produced by the low-coercive force PM (LCFPM). This paper presents a detailed study of the modeling and analysis of rare-earth PM demagnetization in hybrid PM VFMs. An iterative simulation procedure is proposed for predicting rare-earth PM demagnetization while driving the LCFPM to minimum MS. Two plausible causes of demagnetized rare-earth PM operations are investigated. Then, a series-hybrid PM VFM with partially demagnetized rare-earth PMs is tested experimentally to validate the proposed simulation procedure, and a reasonable match is found between the simulation and experimental results. Finally, some design remarks are presented, and two remedial design modifications are proposed, allowing minimal changes in rotor geometrical constraints. Results reveal that for hybrid PM VFMs, it is crucial to model the irreversible demagnetization behavior of rare-earth PM while predicting the re/demagnetization performance.
- 6 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 40 (1) , 490-504
Modeling and Remedies for Rare-Earth Permanent Magnet Demagnetization Effects in Hybrid Permanent Magnet Variable Flux Motors
Variable-flux motors (VFMs) with hybrid permanent magnets (PMs) can limit the utilization of rare-earth PMs and reduce the high-speed losses of traction motors. These motors are often characterized by two main magnetization states (MS), i.e., the maximum and minimum. The flux variation is achieved by applying current pulses. This can be multiples of the rated current and changes the rare-earth PM operating point so that a minimum flux is produced by the low-coercive force PM (LCFPM). This paper presents a detailed study of the modeling and analysis of rare-earth PM demagnetization in hybrid PM VFMs. An iterative simulation procedure is proposed for predicting rare-earth PM demagnetization while driving the LCFPM to minimum MS. Two plausible causes of demagnetized rare-earth PM operations are investigated. Then, a series-hybrid PM VFM with partially demagnetized rare-earth PMs is tested experimentally to validate the proposed simulation procedure, and a reasonable match is found between the simulation and experimental results. Finally, some design remarks are presented, and two remedial design modifications are proposed, allowing minimal changes in rotor geometrical constraints. Results reveal that for hybrid PM VFMs, it is crucial to model the irreversible demagnetization behavior of rare-earth PM while predicting the re/demagnetization performance.
- 21 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (3) , 3278-3290
Design of an Iron Loss Tester for the Evaluation of Assembled Stator Cores of Electric Machines
The manufacturing processes of an electric machine can lead to a deviation between predicted and actual iron losses. This work presents an iron loss tester for measuring the iron losses produced by an assembled stator core including the effects of manufacturing and actual flux distribution. The tester is designed with accessible excitation and measurement windings with a toroidal configuration enabling a high degree of flexibility in emulating various flux distributions in AC electric machines. A prototype of the proposed tester is built and the experimental results of a manufactured stator are obtained under different pole configurations showing the magnetization characteristics in different regions of the tester/stator along with the total measured iron loss (IL). A noticeable deviation between experimental and FE simulation results is present at high frequencies. As the saturation level in steel laminations is reduced, the deviation in total IL is increased. Finally, the specific IL obtained through the tester is compared against standard Epstein frame results. Importing the experimental IL data obtained through the tester to the FE model led to a close match between simulation and experimental results.
- 21 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (3) , 3278-3290
Design of an Iron Loss Tester for the Evaluation of Assembled Stator Cores of Electric Machines
The manufacturing processes of an electric machine can lead to a deviation between predicted and actual iron losses. This work presents an iron loss tester for measuring the iron losses produced by an assembled stator core including the effects of manufacturing and actual flux distribution. The tester is designed with accessible excitation and measurement windings with a toroidal configuration enabling a high degree of flexibility in emulating various flux distributions in AC electric machines. A prototype of the proposed tester is built and the experimental results of a manufactured stator are obtained under different pole configurations showing the magnetization characteristics in different regions of the tester/stator along with the total measured iron loss (IL). A noticeable deviation between experimental and FE simulation results is present at high frequencies. As the saturation level in steel laminations is reduced, the deviation in total IL is increased. Finally, the specific IL obtained through the tester is compared against standard Epstein frame results. Importing the experimental IL data obtained through the tester to the FE model led to a close match between simulation and experimental results.