Guoming Xia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Guoming Xia has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Anping Qiu
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China
8 shared publications - Qin Shi
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China
8 shared publications - Yang Zhao
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China
7 shared publications - Jinyang Huang
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China
4 shared publications - Jie Lin
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China
2 shared publications - Yang Zhao
School of Mechanical Engineering, Department of Instrument Science and Technology, Nanjing University of Science and Technology, Nanjing 210094, Jiangsu, China
1 shared publication
Latest Publications
- 27 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (11) , 16954-16963
Development of a Modular Active Probe Card Equipment for Wafer-Level Multiparameter Fast Characterization and Prediction of High-Q MEMS Gyroscopes
This paper proposes an Active Probe Card (APC) equipment for MEMS gyroscopes offering multi-parameter that address the concerns of manufacturers and end-users. An efficient and reliable frequency and Q-factor (f&Q) measurement method, enabled by a negative impedance converter (NIC), is firstly applied to the one-port sense resonator of the gyroscope. While the gyroscope’s drive loop oscillates continuously, the f&Q measurement periods for drive/sense resonators and the fully operational gyroscope characterization periods are merged. It eliminates the time overhead associated with high-Q mode ring-down, restart-up waiting, and connection reconfiguration. Furthermore, the system incorporates a variable polarization voltage (Vp) function. The true process related monitoring parameters and predictions of gyroscope operating behaviors with specific frequency split (Δf) are automatically extracted from two sequential tests with different Vp loads. The time cost per DUT is <5s. The probes carrier card and active electronics card are interconnected with pluggable shielded cables, facilitating easy upgrading and adaptation to gyroscopes with different pin definitions. Using the proposed APC equipment, we demonstrate it can 1) realize the extraction and monitoring of true dimension and encapsulated pressure parameters in both the same and different process stages;2) perform system-level gyroscope operating behaviors pre-validation and grading at the wafer level.
- 27 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (11) , 16954-16963
Development of a Modular Active Probe Card Equipment for Wafer-Level Multiparameter Fast Characterization and Prediction of High-Q MEMS Gyroscopes
This paper proposes an Active Probe Card (APC) equipment for MEMS gyroscopes offering multi-parameter that address the concerns of manufacturers and end-users. An efficient and reliable frequency and Q-factor (f&Q) measurement method, enabled by a negative impedance converter (NIC), is firstly applied to the one-port sense resonator of the gyroscope. While the gyroscope’s drive loop oscillates continuously, the f&Q measurement periods for drive/sense resonators and the fully operational gyroscope characterization periods are merged. It eliminates the time overhead associated with high-Q mode ring-down, restart-up waiting, and connection reconfiguration. Furthermore, the system incorporates a variable polarization voltage (Vp) function. The true process related monitoring parameters and predictions of gyroscope operating behaviors with specific frequency split (Δf) are automatically extracted from two sequential tests with different Vp loads. The time cost per DUT is <5s. The probes carrier card and active electronics card are interconnected with pluggable shielded cables, facilitating easy upgrading and adaptation to gyroscopes with different pin definitions. Using the proposed APC equipment, we demonstrate it can 1) realize the extraction and monitoring of true dimension and encapsulated pressure parameters in both the same and different process stages;2) perform system-level gyroscope operating behaviors pre-validation and grading at the wafer level.
- 24 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (7) , 10109-10117
Electrical Interconnect Loss Cancellation for MEMS Gyroscopic Resonators via In Situ Integrated Virtual Negative Resistance
Electrical interconnect loss degrades the intrinsic high Q-factor of MEMS gyroscopic resonators and alters their phase response. This paper proposes, for the first time, a loss cancellation approach utilizing an in-situ integrated negative impedance converter (NIC), which requires no additional tuning structures or electrodes. Controllable positive feedback is embedded into the conventional transimpedance amplifier (TIA), yielding a virtual negative resistance (NR) that cancels the interconnect loss or even the intrinsic loss of the resonator itself. We further demonstrate that through proper zero-pole arrangement of the Opam and its feedback network, the NIC can be degenerated into a single-pole system, thereby eliminating stability risk. Serving as the front-end of a split-mode MEMS gyroscope, this scheme recovers the sense Q-factor from a damped value of 2.8k to its intrinsic value of 42k and passively reduces its thermal variation from 52% to 2.1%. Furthermore, it corrects the gyrof’s phase shift from 1.25deg to 0.06deg, corresponding to a reduction in the quadrature leakage coefficient from 2.2% to 0.1% and maintaining a variation of 40ppm over a 100°C-temperature range, even without the use of a high-accurate active stabilization loop.
- 24 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (7) , 10109-10117
Electrical Interconnect Loss Cancellation for MEMS Gyroscopic Resonators via In Situ Integrated Virtual Negative Resistance
Electrical interconnect loss degrades the intrinsic high Q-factor of MEMS gyroscopic resonators and alters their phase response. This paper proposes, for the first time, a loss cancellation approach utilizing an in-situ integrated negative impedance converter (NIC), which requires no additional tuning structures or electrodes. Controllable positive feedback is embedded into the conventional transimpedance amplifier (TIA), yielding a virtual negative resistance (NR) that cancels the interconnect loss or even the intrinsic loss of the resonator itself. We further demonstrate that through proper zero-pole arrangement of the Opam and its feedback network, the NIC can be degenerated into a single-pole system, thereby eliminating stability risk. Serving as the front-end of a split-mode MEMS gyroscope, this scheme recovers the sense Q-factor from a damped value of 2.8k to its intrinsic value of 42k and passively reduces its thermal variation from 52% to 2.1%. Furthermore, it corrects the gyrof’s phase shift from 1.25deg to 0.06deg, corresponding to a reduction in the quadrature leakage coefficient from 2.2% to 0.1% and maintaining a variation of 40ppm over a 100°C-temperature range, even without the use of a high-accurate active stabilization loop.
- 22 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 34 (4) , 443-451
Exploring Bias-Instability Noise Sources in Quadrature Error Compensation System for Mode-Split MEMS Gyroscopes
In this paper, bias instability (BIS) and angle random walk (ARW) noise sources of quadrature correction for mode-split MEMS gyroscopes are first investigated. We propose a general noise model based on coupling stiffness correction that reveals the transfer mechanism of 1/f and white noise sources. The BIS with a small frequency split is mainly dominated by the electrostatic frequency-tuning voltage noise and that with a large frequency split is determined by the voltage reference noise in the quadrature loop. Due to the electrostatic frequency-tuning voltage noise, the quadrature correction system is unable to compensate for the quadrature error to zero. The BIS with quadrature correction is related to the initial quadrature error and frequency split. We find a good match between the presented model and measurements with an error of less than 15.1%. The simulation and experimental results have indicated that ARW will not be deteriorated by the quadrature compensation system. A MEMS mode-split gyroscope has achieved an ARW of $0.029~^{\circ }$ / $\surd $ h and a BIS of $0.08~^{\circ }$ /h under the initial quadrature of $130~^{\circ }$ /s and the frequency split of 85 Hz with quadrature error compensation. [2025-0014]
- 22 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 34 (4) , 443-451
Exploring Bias-Instability Noise Sources in Quadrature Error Compensation System for Mode-Split MEMS Gyroscopes
In this paper, bias instability (BIS) and angle random walk (ARW) noise sources of quadrature correction for mode-split MEMS gyroscopes are first investigated. We propose a general noise model based on coupling stiffness correction that reveals the transfer mechanism of 1/f and white noise sources. The BIS with a small frequency split is mainly dominated by the electrostatic frequency-tuning voltage noise and that with a large frequency split is determined by the voltage reference noise in the quadrature loop. Due to the electrostatic frequency-tuning voltage noise, the quadrature correction system is unable to compensate for the quadrature error to zero. The BIS with quadrature correction is related to the initial quadrature error and frequency split. We find a good match between the presented model and measurements with an error of less than 15.1%. The simulation and experimental results have indicated that ARW will not be deteriorated by the quadrature compensation system. A MEMS mode-split gyroscope has achieved an ARW of $0.029~^{\circ }$ / $\surd $ h and a BIS of $0.08~^{\circ }$ /h under the initial quadrature of $130~^{\circ }$ /s and the frequency split of 85 Hz with quadrature error compensation. [2025-0014]
- 8 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (18) , 28662-28674
Exploring and Identifying Bias-Instability Noise Sources in Mode-Split MEMS Gyroscopes Based on Electrostatic Frequency Tuning
In this paper, bias-instability induced by phase noise via electrostatic frequency tuning is firstly investigated. We propose a noise model that reveals the transfer mechanism of electrostatic frequency tuning on scale factor instability noise and demodulated phase noise in an open-loop sense system of gyroscopes to analyze the relationship between frequency split and noise performances. The 1/f noise sources are the electrostatic frequency tuning voltage noise and drive amplitude noise. By varying the frequency split and monitoring the instability of gyro’s quadrature output and rate output, it is possible to identify these noise sources and contributions to bias instability (BIS) of zero-rate output. This identification also indicates the low bias-instability design criteria from both mechanical and circuit aspects, for example, the needed quadrature coupling rate, Q-factor and frequency split. According to the proposed noise model including amplitude and phase conversion processes, the lower limit of frequency split can be determined considering the bias-instability deterioration effect. A frequency-tuning criterion of open-loop MEMS mode-split gyroscopes for different noise requirement is hence established. Angle random walk (ARW) and BIS together define the adjustable range of frequency split in MEMS gyroscopes. The upper limit of frequency split is set by suppression of the white noise from the interface circuit. The experimental result indicates a MEMS mode-split gyroscope has achieved an ARW of 0.009 °/√h and a BIS of 0.17 °/h under the quadrature of 40 °/s and the frequency split of critical value (110 Hz).
- 8 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (18) , 28662-28674
Exploring and Identifying Bias-Instability Noise Sources in Mode-Split MEMS Gyroscopes Based on Electrostatic Frequency Tuning
In this paper, bias-instability induced by phase noise via electrostatic frequency tuning is firstly investigated. We propose a noise model that reveals the transfer mechanism of electrostatic frequency tuning on scale factor instability noise and demodulated phase noise in an open-loop sense system of gyroscopes to analyze the relationship between frequency split and noise performances. The 1/f noise sources are the electrostatic frequency tuning voltage noise and drive amplitude noise. By varying the frequency split and monitoring the instability of gyro’s quadrature output and rate output, it is possible to identify these noise sources and contributions to bias instability (BIS) of zero-rate output. This identification also indicates the low bias-instability design criteria from both mechanical and circuit aspects, for example, the needed quadrature coupling rate, Q-factor and frequency split. According to the proposed noise model including amplitude and phase conversion processes, the lower limit of frequency split can be determined considering the bias-instability deterioration effect. A frequency-tuning criterion of open-loop MEMS mode-split gyroscopes for different noise requirement is hence established. Angle random walk (ARW) and BIS together define the adjustable range of frequency split in MEMS gyroscopes. The upper limit of frequency split is set by suppression of the white noise from the interface circuit. The experimental result indicates a MEMS mode-split gyroscope has achieved an ARW of 0.009 °/√h and a BIS of 0.17 °/h under the quadrature of 40 °/s and the frequency split of critical value (110 Hz).
- 7 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (18) , 21363-21373
A Novel Frequency Readout Method and Circuit for Navigation-Grade Vibrating Beam Accelerometers
Vibrating beam accelerometers (VBAs) have significant application potential in navigation guidance. This paper proposed a novel high-precision frequency readout method and integrated CMOS circuit implementation for VBAs. And technologies including sigma-delta modulation, up-sample and split, data synchronization and nonlinearity correction are employed in the method which is analyzed in detail in this paper. The method offers the advantages of low quantization noise, enough range, fixed output rate, and high linearity. Other force-frequency sensors could also benefit from this method but note that its noise suppression is most effective when the output rate is much smaller than the frequency under test. The method is implemented by a CMOS circuit and integrated with an oscillator circuit, which makes a full-function single-package VBA possible. Static, shock, random vibration, and centrifugal tests of the frequency readout circuit and VBA were performed. Test results show that the frequency quantization noise is less than 10 μHz/√Hz at 1 Hz, and can support 0.1 μg noise output. They also show that the vibration rectification error is lower than 0.5 mg at 8 grms, and that the 20 g full range nonlinearity is 16 ppm.
- 7 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (18) , 21363-21373
A Novel Frequency Readout Method and Circuit for Navigation-Grade Vibrating Beam Accelerometers
Vibrating beam accelerometers (VBAs) have significant application potential in navigation guidance. This paper proposed a novel high-precision frequency readout method and integrated CMOS circuit implementation for VBAs. And technologies including sigma-delta modulation, up-sample and split, data synchronization and nonlinearity correction are employed in the method which is analyzed in detail in this paper. The method offers the advantages of low quantization noise, enough range, fixed output rate, and high linearity. Other force-frequency sensors could also benefit from this method but note that its noise suppression is most effective when the output rate is much smaller than the frequency under test. The method is implemented by a CMOS circuit and integrated with an oscillator circuit, which makes a full-function single-package VBA possible. Static, shock, random vibration, and centrifugal tests of the frequency readout circuit and VBA were performed. Test results show that the frequency quantization noise is less than 10 μHz/√Hz at 1 Hz, and can support 0.1 μg noise output. They also show that the vibration rectification error is lower than 0.5 mg at 8 grms, and that the 20 g full range nonlinearity is 16 ppm.
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (4) , 4230-4240
Low-Noise Quality Factor Tuning in Nondegenerate MEMS Gyroscope Without Dedicated Tuning Electrode
Quality factor tuning is attractive in degenerate and nondegenerate (NDE) MEMS gyros for drift suppression or shock and vibration immunity. This article proposes three resistance-based Q -factor tuning approaches without dedicated electrodes for NDE gyro. The inherent sensing capacitance is utilized as a Q -tuning mechanism for low cost, size, weight, and power (C-SWaP). Routing traces on MEMS or application-specified integrated circuit chips as well as the input impedance of charge sensitive amplifier (CSA) are utilized as damping sources. The theoretical and experimental results indicate Q -tuning utilizing the CSA's input impedance does not deteriorate the gyro's noise floor (angle random walk = 0.01°/√h, bias instability = 0.12°/h). Large-scale Q -tuning using the regulation of polarization voltage reduces the sensing Q -factor from 38 to 3 k. The gyro's settling time after shock is also reduced from 1.4 to 0.13 s after Q -tuning. Besides, a frequency-independent fine Q -tuning using tail current regulation in Opam is proposed to correct the thermal variation of the sensing Q -factor. It improves the gyro's bias drift from 1.5°/s to 0.2°/s. This work presents a low C-SWaP Q -tuning solution for high-end industrial MEMS gyro.
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (4) , 4230-4240
Low-Noise Quality Factor Tuning in Nondegenerate MEMS Gyroscope Without Dedicated Tuning Electrode
Quality factor tuning is attractive in degenerate and nondegenerate (NDE) MEMS gyros for drift suppression or shock and vibration immunity. This article proposes three resistance-based Q -factor tuning approaches without dedicated electrodes for NDE gyro. The inherent sensing capacitance is utilized as a Q -tuning mechanism for low cost, size, weight, and power (C-SWaP). Routing traces on MEMS or application-specified integrated circuit chips as well as the input impedance of charge sensitive amplifier (CSA) are utilized as damping sources. The theoretical and experimental results indicate Q -tuning utilizing the CSA's input impedance does not deteriorate the gyro's noise floor (angle random walk = 0.01°/√h, bias instability = 0.12°/h). Large-scale Q -tuning using the regulation of polarization voltage reduces the sensing Q -factor from 38 to 3 k. The gyro's settling time after shock is also reduced from 1.4 to 0.13 s after Q -tuning. Besides, a frequency-independent fine Q -tuning using tail current regulation in Opam is proposed to correct the thermal variation of the sensing Q -factor. It improves the gyro's bias drift from 1.5°/s to 0.2°/s. This work presents a low C-SWaP Q -tuning solution for high-end industrial MEMS gyro.
- 25 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 31 (4) , 524-532
Accurate Identification of the Evolution of MEMS Resonant Accelerometer Residual Stresses at the Wafer-Die-Chip Level
In this work, the processing error including the overetching error and residual stresses in the manufacturing process of a microelectromechanical system (MEMS) resonant accelerometer is identified. The performance of the accelerometer is affected by the processing error, especially the residual stress due to the multiple temperature loads in the manufacturing process. Thus, it is essential to identify the processing error for a high-precision MEMS resonant accelerometer. The overetching error is assessed using the sensitivity of the accelerometer resonator. With the multi-step measurement of the resonator frequency variation in the packaging process, the residual stresses of the MEMS accelerometer at different stages are decomposed and identified, combined with surface morphology measurement and finite element analysis simulations. The results of the analysis demonstrate that: 1) The processing error distribution of the accelerometer at the wafer level is related to the morphology of the wafer, which is decided by the low-order main vibrating modes. 2) The residual stress is distributed from high to low from the center to the edge in the wafer. 3) The residual stress at the wafer level is the main part of the MEMS accelerometer when low-stress packaging technology is adopted at the chip level. 4) The variation of the residual stresses in the manufacturing process is a non-monotonic process. The accurate identification of the processing error provides an effective foundation for the improvement and optimization of the MEMS resonant accelerometer. [2022-0041]
- 25 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 31 (4) , 524-532
Accurate Identification of the Evolution of MEMS Resonant Accelerometer Residual Stresses at the Wafer-Die-Chip Level
In this work, the processing error including the overetching error and residual stresses in the manufacturing process of a microelectromechanical system (MEMS) resonant accelerometer is identified. The performance of the accelerometer is affected by the processing error, especially the residual stress due to the multiple temperature loads in the manufacturing process. Thus, it is essential to identify the processing error for a high-precision MEMS resonant accelerometer. The overetching error is assessed using the sensitivity of the accelerometer resonator. With the multi-step measurement of the resonator frequency variation in the packaging process, the residual stresses of the MEMS accelerometer at different stages are decomposed and identified, combined with surface morphology measurement and finite element analysis simulations. The results of the analysis demonstrate that: 1) The processing error distribution of the accelerometer at the wafer level is related to the morphology of the wafer, which is decided by the low-order main vibrating modes. 2) The residual stress is distributed from high to low from the center to the edge in the wafer. 3) The residual stress at the wafer level is the main part of the MEMS accelerometer when low-stress packaging technology is adopted at the chip level. 4) The variation of the residual stresses in the manufacturing process is a non-monotonic process. The accurate identification of the processing error provides an effective foundation for the improvement and optimization of the MEMS resonant accelerometer. [2022-0041]
- Open Access
Expanding Bias-instability of MEMS Silicon Oscillating Accelerometer Utilizing AC Polarization and Self-Compensation
This paper presents a MEMS (Micro-Electro-Mechanical System) Silicon Oscillating Accelerometer (SOA) with AC (alternating current) polarization to expand its bias-instability limited by the up-converted 1/f noise from front-end transimpedance amplifier (TIA). In contrast to the conventional DC (direct current) scheme, AC polarization breaks the trade-off between input transistor gate size and white noise floor of TIA, a relative low input loading capacitance can be implemented for low noise consideration. Besides, a self-compensation technique combining polarization source and reference in automatic-gain-control (AGC) is put forward. It cancels the 1/f noise and drift introduced by the polarization source itself, which applies to both DC and AC polarization cases. The experimental result indicates the proposed AC polarization and self-compensation strategy expand the bias-instability of studied SOA from 2.58 μg to 0.51 μg with a full scale of ± 30 g, a 155.6 dB dynamic range is realized in this work.
Open AccessExpanding Bias-instability of MEMS Silicon Oscillating Accelerometer Utilizing AC Polarization and Self-Compensation
This paper presents a MEMS (Micro-Electro-Mechanical System) Silicon Oscillating Accelerometer (SOA) with AC (alternating current) polarization to expand its bias-instability limited by the up-converted 1/f noise from front-end transimpedance amplifier (TIA). In contrast to the conventional DC (direct current) scheme, AC polarization breaks the trade-off between input transistor gate size and white noise floor of TIA, a relative low input loading capacitance can be implemented for low noise consideration. Besides, a self-compensation technique combining polarization source and reference in automatic-gain-control (AGC) is put forward. It cancels the 1/f noise and drift introduced by the polarization source itself, which applies to both DC and AC polarization cases. The experimental result indicates the proposed AC polarization and self-compensation strategy expand the bias-instability of studied SOA from 2.58 μg to 0.51 μg with a full scale of ± 30 g, a 155.6 dB dynamic range is realized in this work.