Arup Kar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Arup Kar has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Dip Saikia
Department of Physics, Digboi College, Digboi, India
6 shared publications - Pandiyarajan Narayanasamy
Department of Mechanical Engineering, Kamaraj College of Engineering and Technology, Madurai, India
5 shared publications - Sivasubramanian Palanisamy
Department of Mechanical Engineering, School of Engineering, Mohan Babu University, Tirupati-517102, Andhra Pradesh, India
3 shared publications - Carlo Santulli
School of Science and Technology, Università di Camerino
1 shared publication - Cristiano Fragassa
Department of Industrial Engineering, University of Bologna, 40136 Bologna, Italy
1 shared publication - Sabu Thomas
School of Energy Materials Mahatma Gandhi University Kottayam Kerala India
1 shared publication
Latest Publications
- 30 November 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (9) , 7879-7892
Structural, Thermal, and Mechanical Characterization of Vinyl Ester Composites Reinforced With Juglans regia Seed Shell Filler
Vinyl ester (VE) composites were filled with 5–30 wt.% Juglans regia seed shell filler (JRSSF) to evaluate structural, thermal, and mechanical performance. Infrared spectroscopy established strong OH and CO interactions as evidence for effective filler–matrix bonding. X‐ray diffraction established the presence of an amorphous VE peak (2 θ ≈ 18.8°) together with new peaks corresponding to JRSSF crystallites, constituting a stable dual‐phase structure. Thermal analysis established three‐stage degradation, in which 20 wt.% JRSSF corresponds to the highest thermal stability. Mechanical properties were found to be best at 20 wt.%: tensile strength 33.4 MPa, modulus 2.13 GPa, flexural strength 56.3 MPa, flexural modulus 6.98 GPa, impact strength 9.78 kJ/m 2 , and hardness 38, whereas heat‐deflection temperature was raised from 66.6°C (neat VE) to 79.4°C at 30 wt.%. At over 20 wt.% filler, agglomeration, and poor wetting of the matrix decreased performance. Microscopic examination confirmed uniform dispersion and good interfacial adhesion to 20 wt.% with voids and pull‐outs at high loadings. The findings demonstrate that JRSSF, economic lignocellulosic waste, successfully improves the thermal stability, stiffness, and impact strength of VE composites, and 20 wt.% was found to be the best reinforcement level for structural and thermal applications.
- 30 November 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (9) , 7879-7892
Structural, Thermal, and Mechanical Characterization of Vinyl Ester Composites Reinforced With Juglans regia Seed Shell Filler
Vinyl ester (VE) composites were filled with 5–30 wt.% Juglans regia seed shell filler (JRSSF) to evaluate structural, thermal, and mechanical performance. Infrared spectroscopy established strong OH and CO interactions as evidence for effective filler–matrix bonding. X‐ray diffraction established the presence of an amorphous VE peak (2 θ ≈ 18.8°) together with new peaks corresponding to JRSSF crystallites, constituting a stable dual‐phase structure. Thermal analysis established three‐stage degradation, in which 20 wt.% JRSSF corresponds to the highest thermal stability. Mechanical properties were found to be best at 20 wt.%: tensile strength 33.4 MPa, modulus 2.13 GPa, flexural strength 56.3 MPa, flexural modulus 6.98 GPa, impact strength 9.78 kJ/m 2 , and hardness 38, whereas heat‐deflection temperature was raised from 66.6°C (neat VE) to 79.4°C at 30 wt.%. At over 20 wt.% filler, agglomeration, and poor wetting of the matrix decreased performance. Microscopic examination confirmed uniform dispersion and good interfacial adhesion to 20 wt.% with voids and pull‐outs at high loadings. The findings demonstrate that JRSSF, economic lignocellulosic waste, successfully improves the thermal stability, stiffness, and impact strength of VE composites, and 20 wt.% was found to be the best reinforcement level for structural and thermal applications.
- Open Access
- 23 September 2025
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (20) , 27515-27518
Correction to: Characterization of alkali-treated cellulosic fibers derived from Calamus tenuis canes as a potential reinforcement for polymer composites
- 23 September 2025
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (20) , 27515-27518
Open AccessCorrection to: Characterization of alkali-treated cellulosic fibers derived from Calamus tenuis canes as a potential reinforcement for polymer composites
- 24 October 2024
- Published by Springer Nature in Journal of Polymer Research
- Vol. 31 (11) , 1-16
Calamus tenuis fiber reinforced epoxy composites: effect of fiber loading on the tensile, structural, crystalline, thermal and morphological characteristics
- 24 October 2024
- Published by Springer Nature in Journal of Polymer Research
- Vol. 31 (11) , 1-16
Calamus tenuis fiber reinforced epoxy composites: effect of fiber loading on the tensile, structural, crystalline, thermal and morphological characteristics
- 30 September 2024
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 31 (1) , 224-240
Effect of fiber loading on the mechanical, morphological, and dynamic mechanical characteristics of Calamus tenuis fiber reinforced epoxy composites
This research delves into incorporating Calamus tenuis fibers as reinforcing material in polymer composites, conducting a thorough analysis of their viscoelastic, mechanical, and morphological attributes. Employing the hand layup method, Calamus tenuis fiber‐reinforced epoxy composites were crafted across a range of fiber loadings from 0 to 25 wt% with 5 wt% increments. Results highlight significant enhancements in mechanical attributes upon the incorporation of Calamus tenuis fibers into the matrix. Notably, the composite with 10 wt% Calamus tenuis fibers emerges as the top performer, showcasing unparalleled mechanical strength compared to neat epoxy. It achieves the highest tensile strength (21.08 ± 1.03 MPa) and tensile modulus (2.84 ± 0.09 GPa), along with the utmost flexural strength (63.31 ± 1.05 MPa) and flexural modulus (3.12 ± 0.16 GPa). Furthermore, it demonstrates remarkable impact strength (9.40 ± 0.40 J/cm 2 ), emphasizing its resilience. Scanning electron microscopy (SEM) analysis confirms enhanced fiber‐matrix adhesion in the 10 wt% composite. Additionally, dynamic mechanical analysis (DMA) results reveal enhancements in storage and loss modulus, with the 10 wt% composites exhibiting the highest values. However, the damping factor decreases with the inclusion of Calamus tenuis fibers. Overall, a 10 wt% fiber loading is deemed ideal for enhancing the mechanical and dynamic properties of epoxy composites. Highlights: Utilized Calamus tenuis fibers as reinforcing materials in epoxy composites. Investigated the mechanical, morphological, and viscoelastic properties. Calamus tenuis fibers boost epoxy composite mechanical traits significantly. SEM confirms improved fiber‐matrix adhesion in 10 wt% composite. DMA highlights elevated storage and loss modulus in 10 wt% composites.
- 30 September 2024
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 31 (1) , 224-240
Effect of fiber loading on the mechanical, morphological, and dynamic mechanical characteristics of Calamus tenuis fiber reinforced epoxy composites
This research delves into incorporating Calamus tenuis fibers as reinforcing material in polymer composites, conducting a thorough analysis of their viscoelastic, mechanical, and morphological attributes. Employing the hand layup method, Calamus tenuis fiber‐reinforced epoxy composites were crafted across a range of fiber loadings from 0 to 25 wt% with 5 wt% increments. Results highlight significant enhancements in mechanical attributes upon the incorporation of Calamus tenuis fibers into the matrix. Notably, the composite with 10 wt% Calamus tenuis fibers emerges as the top performer, showcasing unparalleled mechanical strength compared to neat epoxy. It achieves the highest tensile strength (21.08 ± 1.03 MPa) and tensile modulus (2.84 ± 0.09 GPa), along with the utmost flexural strength (63.31 ± 1.05 MPa) and flexural modulus (3.12 ± 0.16 GPa). Furthermore, it demonstrates remarkable impact strength (9.40 ± 0.40 J/cm 2 ), emphasizing its resilience. Scanning electron microscopy (SEM) analysis confirms enhanced fiber‐matrix adhesion in the 10 wt% composite. Additionally, dynamic mechanical analysis (DMA) results reveal enhancements in storage and loss modulus, with the 10 wt% composites exhibiting the highest values. However, the damping factor decreases with the inclusion of Calamus tenuis fibers. Overall, a 10 wt% fiber loading is deemed ideal for enhancing the mechanical and dynamic properties of epoxy composites. Highlights: Utilized Calamus tenuis fibers as reinforcing materials in epoxy composites. Investigated the mechanical, morphological, and viscoelastic properties. Calamus tenuis fibers boost epoxy composite mechanical traits significantly. SEM confirms improved fiber‐matrix adhesion in 10 wt% composite. DMA highlights elevated storage and loss modulus in 10 wt% composites.
- 8 April 2024
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (5) , 7881-7899
Characterization of alkali-treated cellulosic fibers derived from Calamus tenuis canes as a potential reinforcement for polymer composites
- 8 April 2024
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (5) , 7881-7899
Characterization of alkali-treated cellulosic fibers derived from Calamus tenuis canes as a potential reinforcement for polymer composites
- Open Access
Effect of Alkali Treatment under Ambient and Heated Conditions on the Physicochemical, Structural, Morphological, and Thermal Properties of Calamus tenuis Cane Fibers
This study explores the effect of alkali treatment at ambient (25 °C) and elevated temperatures (100 °C) on the physicochemical, structural, morphological, and thermal properties of Calamus tenuis cane fibers (CTCFs) for the first time. Our purpose is to investigate their potential use as reinforcement in polymer composites, since cane fibers are generally known for their accurate and consistent geometrical orientation. Treatment with 8% (w/v) sodium hydroxide (NaOH) is carried out at ambient temperature and at 100 °C for 4 h. Chemical analysis and Fourier transform IR spectroscopy (FTIR) indicate some removal of non-cellulosic elements from CTCFs during alkali treatment, resulting in increased surface roughness, as confirmed by using SEM micrographs. This removal of non-cellulosic elements leads to an enhancement in the density of the treated CTCFs. Untreated and treated fibers are analyzed for maximum degradation temperature, thermal stability, and kinetic activation energy (Ea) using thermogravimetric analysis (TGA). In particular, Ea was considerably diminished with treatment and temperature. X-ray diffraction (XRD) results show an improved crystallinity index (37.38% to 44.02%) and crystallite size (2.73 nm to 2.98 nm) for fibers treated with 8% NaOH at ambient temperature. In conclusion, a general benefit was achieved by treating CTCFs, though the influence of increasing temperature treatment appears controversial.
Open AccessEffect of Alkali Treatment under Ambient and Heated Conditions on the Physicochemical, Structural, Morphological, and Thermal Properties of Calamus tenuis Cane Fibers
This study explores the effect of alkali treatment at ambient (25 °C) and elevated temperatures (100 °C) on the physicochemical, structural, morphological, and thermal properties of Calamus tenuis cane fibers (CTCFs) for the first time. Our purpose is to investigate their potential use as reinforcement in polymer composites, since cane fibers are generally known for their accurate and consistent geometrical orientation. Treatment with 8% (w/v) sodium hydroxide (NaOH) is carried out at ambient temperature and at 100 °C for 4 h. Chemical analysis and Fourier transform IR spectroscopy (FTIR) indicate some removal of non-cellulosic elements from CTCFs during alkali treatment, resulting in increased surface roughness, as confirmed by using SEM micrographs. This removal of non-cellulosic elements leads to an enhancement in the density of the treated CTCFs. Untreated and treated fibers are analyzed for maximum degradation temperature, thermal stability, and kinetic activation energy (Ea) using thermogravimetric analysis (TGA). In particular, Ea was considerably diminished with treatment and temperature. X-ray diffraction (XRD) results show an improved crystallinity index (37.38% to 44.02%) and crystallite size (2.73 nm to 2.98 nm) for fibers treated with 8% NaOH at ambient temperature. In conclusion, a general benefit was achieved by treating CTCFs, though the influence of increasing temperature treatment appears controversial.