Mengke Tang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mengke Tang has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
Cunmin Wang
School of Safety Engineering, China University of Mining and Technology, Xuzhou 221116, China
5 shared publications- Huan Xu
China University of Mining and Technology
5 shared publications Xinjian He
School of Safety Engineering, China University of Mining and Technology, Xuzhou 221116, China
4 shared publicationsXinyi Song
School of Safety Engineering, China University of Mining and Technology, Xuzhou 221116, China
4 shared publicationsXinyu Li
School of Safety Engineering, China University of Mining and Technology, Xuzhou 221116, China
4 shared publicationsJintuo Zhu
School of Safety Engineering, China University of Mining and Technology, Xuzhou 221116, China
3 shared publications
Latest Publications
- Open Access
- 1 April 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Electrochemically induced carbon dioxide capture from air with an aqueous fluoflavine sorbent
Direct air capture (DAC) holds great potential in mitigating climate change. A promising approach is redox sorbent-based electrochemically induced DAC, which operates at ambient conditions with significantly lower energy costs while utilizing clean electricity. However, the oxygen sensitivity of redox sorbents remains a major challenge. Thus, the feasibility of achieving electrochemically induced DAC with redox sorbents remains uncertain. Despite the vast difference in partial pressures between carbon dioxide (CO2) and molecular oxygen (O2) in air, ribulose-1,5-bisphosphate in plant leaves can preferentially react with CO2 in the sunlight, thus achieving the net CO2 removal. Motivated by the nature-based DAC solution, we hereby developed an aqueous-soluble oxygen-tolerant fluoflavine disulfonate (FFDS) sorbent for DAC. Electrochemical characterizations, spectroscopic studies, along with theoretical calculations, reveal that FFDS undergoes proton-coupled electron transfer and exhibits a redox potential higher than the two-electron transfer oxygen reduction potential. When exposed to simulated flue gas containing 10% O2, the FFDS sorbent demonstrates reversible CO2 capture and release with an average CO2/e molar ratio of 0.88. Implemented for both indoor and outdoor DAC in Singapore, FFDS sorbent shows stable cycling performance over 40 days with a three-day DAC under the normal discharge-charge mode, and exhibits an enhanced CO2 capture capacity and a Coulombic efficiency exceeding 99% with an accelerated overnight DAC under the deep discharge-charge mode. Doubling the concentration of FFDS leads to a twofold increase in CO2 capture/release capacity, regardless of whether the three-day DAC is conducted indoors or outdoors. The energy cost for CO2 release and sorbent regeneration ranges from 58 to 190 kJ mol–1 CO2, depending on the applied current densities and discharge-charge modes.
- 1 April 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessElectrochemically induced carbon dioxide capture from air with an aqueous fluoflavine sorbent
Direct air capture (DAC) holds great potential in mitigating climate change. A promising approach is redox sorbent-based electrochemically induced DAC, which operates at ambient conditions with significantly lower energy costs while utilizing clean electricity. However, the oxygen sensitivity of redox sorbents remains a major challenge. Thus, the feasibility of achieving electrochemically induced DAC with redox sorbents remains uncertain. Despite the vast difference in partial pressures between carbon dioxide (CO2) and molecular oxygen (O2) in air, ribulose-1,5-bisphosphate in plant leaves can preferentially react with CO2 in the sunlight, thus achieving the net CO2 removal. Motivated by the nature-based DAC solution, we hereby developed an aqueous-soluble oxygen-tolerant fluoflavine disulfonate (FFDS) sorbent for DAC. Electrochemical characterizations, spectroscopic studies, along with theoretical calculations, reveal that FFDS undergoes proton-coupled electron transfer and exhibits a redox potential higher than the two-electron transfer oxygen reduction potential. When exposed to simulated flue gas containing 10% O2, the FFDS sorbent demonstrates reversible CO2 capture and release with an average CO2/e molar ratio of 0.88. Implemented for both indoor and outdoor DAC in Singapore, FFDS sorbent shows stable cycling performance over 40 days with a three-day DAC under the normal discharge-charge mode, and exhibits an enhanced CO2 capture capacity and a Coulombic efficiency exceeding 99% with an accelerated overnight DAC under the deep discharge-charge mode. Doubling the concentration of FFDS leads to a twofold increase in CO2 capture/release capacity, regardless of whether the three-day DAC is conducted indoors or outdoors. The energy cost for CO2 release and sorbent regeneration ranges from 58 to 190 kJ mol–1 CO2, depending on the applied current densities and discharge-charge modes.
- 19 August 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (34) , 45078-45090
Interfacial Polarization Strategy to Electroactive Poly(lactic acid) Nanofibers for Humidity-Resistant Respiratory Protection and Machine Learning-Assisted Monitoring
The advancement of intelligent and biodegradable respiratory protection equipment is pivotal in the realm of human health engineering. Despite significant progress, achieving a balance between efficient filtration and intelligent monitoring remains a great challenge, especially under conditions of high relative humidity (RH) and high airflow rate (AR). Herein, we proposed an interfacial stereocomplexation (ISC) strategy to facilitate intensive interfacial polarization for poly(lactic acid) (PLA) nanofibrous membranes, which were customized for machine learning-assisted respiratory diagnosis. Theoretical principles underlying the facilitated formation of the electroactive phase and aligned PLA chains were quantitatively depicted in the ISC-PLA nanofibers, contributing to the increased dielectric constant and surface potential (as high as 2.2 and 5.1 kV, respectively). Benefiting from the respiration-driven triboelectric mechanisms, the ISC-PLA demonstrated a high PM0.3 filtration efficiency of over 99% with an ultralow pressure drop (75 Pa), even in challenging circumstances (95 ± 5% RH, AR of 85 L/min). Furthermore, we implemented the ISC-PLA with multifunction respiratory monitoring (response time of 0.56 s and recovery time of 0.25 s) and wireless transmission technology, yielding a high recognition rate of 83% for personal breath states. This innovation has practical implications for health management and theoretical advancements in respiratory protection equipment.
- 19 August 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (34) , 45078-45090
Interfacial Polarization Strategy to Electroactive Poly(lactic acid) Nanofibers for Humidity-Resistant Respiratory Protection and Machine Learning-Assisted Monitoring
The advancement of intelligent and biodegradable respiratory protection equipment is pivotal in the realm of human health engineering. Despite significant progress, achieving a balance between efficient filtration and intelligent monitoring remains a great challenge, especially under conditions of high relative humidity (RH) and high airflow rate (AR). Herein, we proposed an interfacial stereocomplexation (ISC) strategy to facilitate intensive interfacial polarization for poly(lactic acid) (PLA) nanofibrous membranes, which were customized for machine learning-assisted respiratory diagnosis. Theoretical principles underlying the facilitated formation of the electroactive phase and aligned PLA chains were quantitatively depicted in the ISC-PLA nanofibers, contributing to the increased dielectric constant and surface potential (as high as 2.2 and 5.1 kV, respectively). Benefiting from the respiration-driven triboelectric mechanisms, the ISC-PLA demonstrated a high PM0.3 filtration efficiency of over 99% with an ultralow pressure drop (75 Pa), even in challenging circumstances (95 ± 5% RH, AR of 85 L/min). Furthermore, we implemented the ISC-PLA with multifunction respiratory monitoring (response time of 0.56 s and recovery time of 0.25 s) and wireless transmission technology, yielding a high recognition rate of 83% for personal breath states. This innovation has practical implications for health management and theoretical advancements in respiratory protection equipment.
- 5 July 2024
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 12 (32) , 12216-12225
Multi-Protection from Microbial and PM Pollutants by Humidity-Resistant, Breathable and Self-Charging Nanofibrous Membranes
- 5 July 2024
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 12 (32) , 12216-12225
Multi-Protection from Microbial and PM Pollutants by Humidity-Resistant, Breathable and Self-Charging Nanofibrous Membranes
- 1 February 2024
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 12 (9) , 3554-3564
Stereocomplexation-Enhanced Electroactivity of Poly(lactic acid) Nanofibrous Membranes for Long-Term PM Capturing and Remote Respiratory Monitoring
- 1 February 2024
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 12 (9) , 3554-3564
Stereocomplexation-Enhanced Electroactivity of Poly(lactic acid) Nanofibrous Membranes for Long-Term PM Capturing and Remote Respiratory Monitoring
- 1 December 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (2) , 718-732
Study on the temperature field distribution of the interface and process parameter optimization for material extrusion of PLA
Despite the significant development and wide application of 3D printing technology, there are rarely reports on the influence of the build plate temperature upon the manufactured products. By conducting transient thermal analysis and 3D printing experiments, researchers optimized the build plate temperature for reducing defects in printed samples formed through material extrusion (MEX). The temperature distribution near the bottom interface was analyzed using ANSYS parametric design language (APDL) numerical calculation, and the temperature variation at the key monitoring node was examined for different build plate temperatures. Standard samples were then prepared to study warping and tensile properties. The results indicated that sagging would occur when the key monitoring node's temperature exceeded the glass state temperature of the PLA filament, particularly at build plate temperatures of 55 and 60°C. This conclusion was verified through MEX experiments. Ultimately, without sagging, an optimal build plate temperature of 50°C was determined based on APDL calculations, warping measurements (0.42 mm), and tensile yield strength (39.63 MPa). Thus, research on this parameter of temperature field distribution will contribute to the realization of high‐quality and high‐precision 3D printing.Highlights: Optimized the build plate temperature to reduce defects of MEX. The temperature distribution of the interface near the bottom was analyzed by APDL and monitored. Optimal temperature was discussed by combining the results of APDL and experiment data.
- 1 December 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (2) , 718-732
Study on the temperature field distribution of the interface and process parameter optimization for material extrusion of PLA
Despite the significant development and wide application of 3D printing technology, there are rarely reports on the influence of the build plate temperature upon the manufactured products. By conducting transient thermal analysis and 3D printing experiments, researchers optimized the build plate temperature for reducing defects in printed samples formed through material extrusion (MEX). The temperature distribution near the bottom interface was analyzed using ANSYS parametric design language (APDL) numerical calculation, and the temperature variation at the key monitoring node was examined for different build plate temperatures. Standard samples were then prepared to study warping and tensile properties. The results indicated that sagging would occur when the key monitoring node's temperature exceeded the glass state temperature of the PLA filament, particularly at build plate temperatures of 55 and 60°C. This conclusion was verified through MEX experiments. Ultimately, without sagging, an optimal build plate temperature of 50°C was determined based on APDL calculations, warping measurements (0.42 mm), and tensile yield strength (39.63 MPa). Thus, research on this parameter of temperature field distribution will contribute to the realization of high‐quality and high‐precision 3D printing.Highlights: Optimized the build plate temperature to reduce defects of MEX. The temperature distribution of the interface near the bottom was analyzed by APDL and monitored. Optimal temperature was discussed by combining the results of APDL and experiment data.
- 29 May 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (22) , 26812-26823
Biodegradable MOFilters for Effective Air Filtration and Sterilization by Coupling MOF Functionalization and Mechanical Polarization of Fibrous Poly(lactic acid)
High-performance air filtration materials are important for addressing the airborne pollutants. Herein, we propose an unprecedented access to biodegradable poly(lactic acid) (PLA)-based MOFilters with excellent filtering performance and antibacterial activity. The fabrication involved a stepwise in situ growth of zeolitic imidazolate framework-8 (ZIF-8) crystals at the surface of microfibrous PLA membranes, followed by mechanical polarization under high pressure and low temperature (5 MPa, 40 °C) to trigger the ordered alignment of dipoles in PLA chains and ZIF-8. The unique structural features allowed these PLA-based MOFilters to achieve an exceptional combination of excellent tensile properties, high dielectric constant (up to 2.4 F/m), and enhanced surface potential as high as 4 kV. Arising from the remarkable surface activity and electrostatic adsorption effect, a significant increase (from over 12% to nearly 20%) in PM0.3 filtration efficiency was observed for the PLA-based MOFilters compared to that of pure PLA counterparts, with weak relation to the airflow velocities (10-85 L/min). Moreover, the air resistance was controlled at a considerably low level for all the MOFilters, that is, below 183 Pa even at 85 L/min. It is worth noting that distinct antibacterial properties were achieved for the MOFilters, as illustrated by the inhibitive rates of 87 and 100% against Escherichia coli and Staphylococcus aureus, respectively. The proposed concept of PLA-based MOFilters offers unprecedented multifunction integration, which may fuel the development of biodegradable versatile filters with high capturing and antibacterial performances yet desirable manufacturing feasibility.
- 29 May 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (22) , 26812-26823
Biodegradable MOFilters for Effective Air Filtration and Sterilization by Coupling MOF Functionalization and Mechanical Polarization of Fibrous Poly(lactic acid)
High-performance air filtration materials are important for addressing the airborne pollutants. Herein, we propose an unprecedented access to biodegradable poly(lactic acid) (PLA)-based MOFilters with excellent filtering performance and antibacterial activity. The fabrication involved a stepwise in situ growth of zeolitic imidazolate framework-8 (ZIF-8) crystals at the surface of microfibrous PLA membranes, followed by mechanical polarization under high pressure and low temperature (5 MPa, 40 °C) to trigger the ordered alignment of dipoles in PLA chains and ZIF-8. The unique structural features allowed these PLA-based MOFilters to achieve an exceptional combination of excellent tensile properties, high dielectric constant (up to 2.4 F/m), and enhanced surface potential as high as 4 kV. Arising from the remarkable surface activity and electrostatic adsorption effect, a significant increase (from over 12% to nearly 20%) in PM0.3 filtration efficiency was observed for the PLA-based MOFilters compared to that of pure PLA counterparts, with weak relation to the airflow velocities (10-85 L/min). Moreover, the air resistance was controlled at a considerably low level for all the MOFilters, that is, below 183 Pa even at 85 L/min. It is worth noting that distinct antibacterial properties were achieved for the MOFilters, as illustrated by the inhibitive rates of 87 and 100% against Escherichia coli and Staphylococcus aureus, respectively. The proposed concept of PLA-based MOFilters offers unprecedented multifunction integration, which may fuel the development of biodegradable versatile filters with high capturing and antibacterial performances yet desirable manufacturing feasibility.
- 16 May 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (21) , 25919-25931
Bioelectrets in Electrospun Bimodal Poly(lactic acid) Fibers: Realization of Multiple Mechanisms for Efficient and Long-Term Filtration of Fine PMs
Despite the great potential in fabrication of biodegradable and eco-friendly air filters by electrospinning poly(lactic acid) (PLA) membranes, the filtering performance is frequently dwarfed by inadequate physical sieving or electrostatic adsorption mechanisms to capture airborne particulate matters (PMs). Here, using the parallel spinning approach, the unique micro/nanoscale architecture was established by conjugation of neighboring PLA nanofibers, creating bimodal fibers in electrospun PLA membranes for the enhanced slip effect to significantly reduce the air resistance. Moreover, the bone-like nanocrystalline hydroxyapatite bioelectret (HABE) was exploited to enhance the dielectric and polarization properties of electrospun PLA, accompanied by the controlled generation of junctions induced by the microaggregation of HABE (10-30 wt %). The incorporated HABE was supposed to orderly align in the applied E-field and largely promote the charging capability and surface potential, gradually increasing to 7.2 kV from the lowest level of 2.5 kV for pure PLA. This was mainly attributed to HABE-induced orientation of PLA backbone chains and C═O dipoles, as well as the interfacial charges trapped at the interphases of HABE-PLA and crystalline region-amorphous PLA. Given the multiple capturing mechanisms, the micro/nanostructured PLA/HABE membranes were characterized by excellent and sustainable filtering performance, e.g., the filtration efficiency of PM0.3 was promoted from 59.38% for pure PLA to 94.38% after addition of 30 wt % HABE at a moderate airflow capacity of 32 L/min and from 30.78 to 83.75% at the highest level of 85 L/min. It is of interest that the pressure drop was significantly decreased, mainly arising from the slip effect between the ultrafine nanofibers and conjugated microfibers. The proposed combination of the nanostructured electret and the multistructuring strategy offers the function integration of efficient filtration and low resistance that are highly useful to pursue fully biodegradable filters.
- 16 May 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (21) , 25919-25931
Bioelectrets in Electrospun Bimodal Poly(lactic acid) Fibers: Realization of Multiple Mechanisms for Efficient and Long-Term Filtration of Fine PMs
Despite the great potential in fabrication of biodegradable and eco-friendly air filters by electrospinning poly(lactic acid) (PLA) membranes, the filtering performance is frequently dwarfed by inadequate physical sieving or electrostatic adsorption mechanisms to capture airborne particulate matters (PMs). Here, using the parallel spinning approach, the unique micro/nanoscale architecture was established by conjugation of neighboring PLA nanofibers, creating bimodal fibers in electrospun PLA membranes for the enhanced slip effect to significantly reduce the air resistance. Moreover, the bone-like nanocrystalline hydroxyapatite bioelectret (HABE) was exploited to enhance the dielectric and polarization properties of electrospun PLA, accompanied by the controlled generation of junctions induced by the microaggregation of HABE (10-30 wt %). The incorporated HABE was supposed to orderly align in the applied E-field and largely promote the charging capability and surface potential, gradually increasing to 7.2 kV from the lowest level of 2.5 kV for pure PLA. This was mainly attributed to HABE-induced orientation of PLA backbone chains and C═O dipoles, as well as the interfacial charges trapped at the interphases of HABE-PLA and crystalline region-amorphous PLA. Given the multiple capturing mechanisms, the micro/nanostructured PLA/HABE membranes were characterized by excellent and sustainable filtering performance, e.g., the filtration efficiency of PM0.3 was promoted from 59.38% for pure PLA to 94.38% after addition of 30 wt % HABE at a moderate airflow capacity of 32 L/min and from 30.78 to 83.75% at the highest level of 85 L/min. It is of interest that the pressure drop was significantly decreased, mainly arising from the slip effect between the ultrafine nanofibers and conjugated microfibers. The proposed combination of the nanostructured electret and the multistructuring strategy offers the function integration of efficient filtration and low resistance that are highly useful to pursue fully biodegradable filters.