Vinícius Vigolo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vinícius Vigolo has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Victor Juliano De Negri
Department of Mechanical Engineering, LASHIP, Federal University of Santa Catarina, Trindade, Florianópolis, Brazil
4 shared publications - Antonio Carlos Valdiero
Federal University of Santa Catarina
3 shared publications - Daniel A. L. da Cruz
Federal University of Uberlândia, Uberlândia, Brazil
1 shared publication - Gregori Picolotto Conterato
Reivax Automation and Control, Florianópolis, Santa Catarina
1 shared publication - Isaac Varela Brito Guimarães de Souza
Federal University of Santa Catarina, Florianópolis, Santa Catarina
1 shared publication - Joao Carlos Espindola Ferreira
Universidade Federal de Santa Catarina, Brasil
1 shared publication
Latest Publications
- Open Access
- 1 September 2025
- Published by Springer Nature
- p. 63-82
Analysis of the Operating Point Method for Dimensioning of Pneumatic Drives Under Variable Loading Conditions
This paper addresses aspects related to the characteristics of pneumatic applications and their impact on cylinder dimensioning using the operating point method, an approach under development to balance energy efficiency and dynamic performance in pneumatic drives. Initially, pneumatic applications are categorized based on the characteristic behavior of the load forces throughout the piston stroke. Subsequently, an extensive study is conducted to demonstrate the suitability of the operating point method for applications with variable loading conditions. Guidelines are then provided for implementing the operating point method in diverse scenarios, including equations to characterize the load force of the application and an approximate analytical solution for the operating point method. Simulations are carried out for fifty distinct working conditions, with loading components including gravitational force, spring, damper, and inertial forces. The simulations evidence the capability of the operating point method to balance aspects of energy efficiency, dynamic performance, and robustness of pneumatic drives under non-constant load force operation.
- 1 September 2025
- Published by Springer Nature
- p. 63-82
Open AccessAnalysis of the Operating Point Method for Dimensioning of Pneumatic Drives Under Variable Loading Conditions
This paper addresses aspects related to the characteristics of pneumatic applications and their impact on cylinder dimensioning using the operating point method, an approach under development to balance energy efficiency and dynamic performance in pneumatic drives. Initially, pneumatic applications are categorized based on the characteristic behavior of the load forces throughout the piston stroke. Subsequently, an extensive study is conducted to demonstrate the suitability of the operating point method for applications with variable loading conditions. Guidelines are then provided for implementing the operating point method in diverse scenarios, including equations to characterize the load force of the application and an approximate analytical solution for the operating point method. Simulations are carried out for fifty distinct working conditions, with loading components including gravitational force, spring, damper, and inertial forces. The simulations evidence the capability of the operating point method to balance aspects of energy efficiency, dynamic performance, and robustness of pneumatic drives under non-constant load force operation.
- Open Access
- 13 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 30 (6) , 4503-4513
A Model-Based Approach for Online Optimization of Pneumatic Drives
This article presents an online monitoring and setup strategy to optimize the operating conditions of pneumatic drives. The strategy integrates a model-based optimization approach with a hybrid machine learning (HML) model designed to assess the loading conditions and improve the performance of pneumatic actuators. Employing the operating point method, a model-based approach, the HML model seeks an optimal balance between energy efficiency and robustness. A strategy based on the chambers’ pressures is applied on the HML model to assess in real-time the actual load being applied on the cylinder, establishing a reference pair of pressure ratios, and making it suitable for nonconstant load force applications. A sensitivity analysis is performed to evaluate the impact of the uncertainties associated with the operating point parameters on the HML model output. Experimental results under several load conditions demonstrated its ability to significantly reduce air consumption in underloaded scenarios. Furthermore, the HML approach improved system robustness in overloaded cases, mitigating the impact on displacement time due to possible load variations. Comparative evaluations with a conventional architecture and a commercially available energy-saving device highlight the capabilities of the proposed online monitoring strategy of cost-effectively enhancing the operation of pneumatic drives.
- 13 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 30 (6) , 4503-4513
Open AccessA Model-Based Approach for Online Optimization of Pneumatic Drives
This article presents an online monitoring and setup strategy to optimize the operating conditions of pneumatic drives. The strategy integrates a model-based optimization approach with a hybrid machine learning (HML) model designed to assess the loading conditions and improve the performance of pneumatic actuators. Employing the operating point method, a model-based approach, the HML model seeks an optimal balance between energy efficiency and robustness. A strategy based on the chambers’ pressures is applied on the HML model to assess in real-time the actual load being applied on the cylinder, establishing a reference pair of pressure ratios, and making it suitable for nonconstant load force applications. A sensitivity analysis is performed to evaluate the impact of the uncertainties associated with the operating point parameters on the HML model output. Experimental results under several load conditions demonstrated its ability to significantly reduce air consumption in underloaded scenarios. Furthermore, the HML approach improved system robustness in overloaded cases, mitigating the impact on displacement time due to possible load variations. Comparative evaluations with a conventional architecture and a commercially available energy-saving device highlight the capabilities of the proposed online monitoring strategy of cost-effectively enhancing the operation of pneumatic drives.
- Open Access
- 30 August 2024
- Published by Springer Nature in Journal of Intelligent & Robotic Systems
- Vol. 110 (3) , 1-14
HOPE-G: A Dual Belt Treadmill Servo-Pneumatic System for Gait Rehabilitation
- 30 August 2024
- Published by Springer Nature in Journal of Intelligent & Robotic Systems
- Vol. 110 (3) , 1-14
Open AccessHOPE-G: A Dual Belt Treadmill Servo-Pneumatic System for Gait Rehabilitation
- Open Access
- 23 March 2023
- Published by Linkoping University Electronic Press in Swedish Aerospace Conference, FT2025
- p. 45-50
Frugal Approach for The Design of a Rehabilitation Physical System
In the rehabilitation process, robotic structures can support the different medical-surgical actions. These recovery process activities often involve repetitive movements that must be performed several times at various amplitudes. Robotic structures for rehabilitation can be driven by three types of active drives, namely electric, pneumatic and hydraulic actuators. Pneumatic systems have become increasingly present in various market segments and are widely used in the industry, mainly due to their ease of maintenance, low cost, safety and applicability in various processes. Currently, the concept of Frugal Innovation is being discussed, which emerges as a way to produce effective and affordable products using fewer resources to reach less-served customers. Frugal Innovation is centered on saving resources, is characterized by simplicity and clarity and aims to reach the low-income market. This article proposes the application of Frugal development methods in the design of a lower limb rehabilitation system. With the application of frugal concepts, pneumatic actuators were chosen. The choice of the pneumatic cylinder is presented from the required pneumatic force. The application of the Frugal Innovation approach in the design of this type of products demonstrates the relevance of applying these methods in efforts to mitigate or reduce the growth of the technological gap between underdeveloped and developed countries.
- 23 March 2023
- Published by Linkoping University Electronic Press in Swedish Aerospace Conference, FT2025
- p. 45-50
Open AccessFrugal Approach for The Design of a Rehabilitation Physical System
In the rehabilitation process, robotic structures can support the different medical-surgical actions. These recovery process activities often involve repetitive movements that must be performed several times at various amplitudes. Robotic structures for rehabilitation can be driven by three types of active drives, namely electric, pneumatic and hydraulic actuators. Pneumatic systems have become increasingly present in various market segments and are widely used in the industry, mainly due to their ease of maintenance, low cost, safety and applicability in various processes. Currently, the concept of Frugal Innovation is being discussed, which emerges as a way to produce effective and affordable products using fewer resources to reach less-served customers. Frugal Innovation is centered on saving resources, is characterized by simplicity and clarity and aims to reach the low-income market. This article proposes the application of Frugal development methods in the design of a lower limb rehabilitation system. With the application of frugal concepts, pneumatic actuators were chosen. The choice of the pneumatic cylinder is presented from the required pneumatic force. The application of the Frugal Innovation approach in the design of this type of products demonstrates the relevance of applying these methods in efforts to mitigate or reduce the growth of the technological gap between underdeveloped and developed countries.
- Open Access
- 23 March 2023
- Published by Linkoping University Electronic Press in Swedish Aerospace Conference, FT2025
- Vol. 196, 67-76
Development of Pneumatic Technology for Automation and Control of Small Hydropower Plants
Small hydropower plants have been seen as a more sustainable source of energy in comparison with large hydropower plants due to the smaller required flooding area. However, every source of energy production has, inevitably, an impact on the environment. Aiming to reduce the usage of fossil-based products, such as hydraulic oil, a joint effort has been made between the Laboratory of Hydraulic and Pneumatic systems and the companies Reivax Automation and Control and China Three Gorges, in order to introduce the pneumatic technology to the hydrogeneration sector. Characteristics such as easy installation and maintenance, low acquisition costs, and mainly, low environmental impact, make the pneumatic technology an excellent candidate to replace the hydraulic servo actuators that have been traditionally used for automation and control in hydropower plants, which use large quantities of hydraulic oil and provide a high risk of a river bed contamination due to possible leakages or incorrect disposal of hydraulic oil. This paper presents two cycles of development of a pneumatic solution to automate and control the generating unit of small hydropower plants. It includes the first proposed solutions, proof of concepts and drawbacks that were faced, as well as the new challenges and achievements that rose during the design process. The paper also presents the most up-to-date results from a pilot project where a fully pneumatic solution was applied for a generating unit with 438 kVA of generating capacity and a model of development that was identified based on common activities performed during the first two cycles of development.
- 23 March 2023
- Published by Linkoping University Electronic Press in Swedish Aerospace Conference, FT2025
- Vol. 196, 67-76
Open AccessDevelopment of Pneumatic Technology for Automation and Control of Small Hydropower Plants
Small hydropower plants have been seen as a more sustainable source of energy in comparison with large hydropower plants due to the smaller required flooding area. However, every source of energy production has, inevitably, an impact on the environment. Aiming to reduce the usage of fossil-based products, such as hydraulic oil, a joint effort has been made between the Laboratory of Hydraulic and Pneumatic systems and the companies Reivax Automation and Control and China Three Gorges, in order to introduce the pneumatic technology to the hydrogeneration sector. Characteristics such as easy installation and maintenance, low acquisition costs, and mainly, low environmental impact, make the pneumatic technology an excellent candidate to replace the hydraulic servo actuators that have been traditionally used for automation and control in hydropower plants, which use large quantities of hydraulic oil and provide a high risk of a river bed contamination due to possible leakages or incorrect disposal of hydraulic oil. This paper presents two cycles of development of a pneumatic solution to automate and control the generating unit of small hydropower plants. It includes the first proposed solutions, proof of concepts and drawbacks that were faced, as well as the new challenges and achievements that rose during the design process. The paper also presents the most up-to-date results from a pilot project where a fully pneumatic solution was applied for a generating unit with 438 kVA of generating capacity and a model of development that was identified based on common activities performed during the first two cycles of development.
- 15 December 2020
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 143 (5)
Sizing Optimization of Pneumatic Actuation Systems Through Operating Point Analysis
This paper reports a study on the static and dynamic behavior of pneumatic actuation systems, resulting in a comprehensive view of the influence of the system parameters on the energy efficiency and dynamic performance. The operating point approach based on the steady-state analysis of a pneumatic actuation system is used for developing analytical expressions to describe the relationship between the piston diameter and the system performance, including displacement time, stroke end velocity, and energy efficiency. The validity of the proposed equations is demonstrated by comparison with results from a test rig. Sensitivity analysis using a nonlinear dynamic simulation model indicated that a specific operating region exists, where good energy efficiency and the maximum dynamic performance are achieved. Moreover, the results show that an oversized system becomes more inefficient in both energetic and dynamic aspects. The results obtained provide a very consistent foundation for developing a method for pneumatic system sizing.
- 15 December 2020
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 143 (5)
Sizing Optimization of Pneumatic Actuation Systems Through Operating Point Analysis
This paper reports a study on the static and dynamic behavior of pneumatic actuation systems, resulting in a comprehensive view of the influence of the system parameters on the energy efficiency and dynamic performance. The operating point approach based on the steady-state analysis of a pneumatic actuation system is used for developing analytical expressions to describe the relationship between the piston diameter and the system performance, including displacement time, stroke end velocity, and energy efficiency. The validity of the proposed equations is demonstrated by comparison with results from a test rig. Sensitivity analysis using a nonlinear dynamic simulation model indicated that a specific operating region exists, where good energy efficiency and the maximum dynamic performance are achieved. Moreover, the results show that an oversized system becomes more inefficient in both energetic and dynamic aspects. The results obtained provide a very consistent foundation for developing a method for pneumatic system sizing.