Marcos Paulo Nostrani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Marcos Paulo Nostrani has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Victor Juliano De Negri
Department of Mechanical Engineering, LASHIP, Federal University of Santa Catarina, Trindade, Florianópolis, Brazil
5 shared publications - Dimitri Oliveira e Silva
Federal University of Southern and Southeastern Para
3 shared publications - Petter Krus
Linköping University
2 shared publications - Tulio De Abreu Burgos Gonçalves
Federal University of Santa Catarina
2 shared publications - Alessandro Dell’aMico
Department of Management and Engineering (IEI), Linköping University, 581 83 Linköping, Sweden
1 shared publication - Gierri Waltrich
Federal University of Santa Catarina
1 shared publication
Latest Publications
- 18 November 2025
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 17 (3) , 1259-1274
Technology demonstrators’ guidelines: a contribution to technology funding and transfer process
- 18 November 2025
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 17 (3) , 1259-1274
Technology demonstrators’ guidelines: a contribution to technology funding and transfer process
- Open Access
- 28 October 2025
- Published by Linkoping University Electronic Press in Swedish Aerospace Conference, FT2025
- Vol. 215
Redundant Digital Hydraulic Actuators for Flight Control Surfaces
The aircraft industry is continually driven to improve energy efficiency in response to environmental concerns and cost reduction. Among solutions available in the field, hydraulics is commonly chosen to deliver crucial functions for its known reliability, precise controllability, and high stiffness. Additionally, when compared to competing technologies in development, hydraulic systems are far less susceptible to jamming, heat rejection problems, and premature wear. In the current context, digital hydraulics emerges as a promising alternative to conventional hydraulics, greatly increasing energy efficiency while keeping the robustness of fluid power systems. Aiming to apply this technology to aircraft systems, this paper introduces enhancements for the digital hydraulic topologies developed at LASHIP/UFSC that allow them to be applied in critical tasks, such as flight control actuation, achieving reliability and performance criteria, beyond the increase in efficiency. These topologies were refined with segregation and independence principles, as is standard in aircraft. The solutions address both centralized (easier to adapt to existing aircraft designs) and distributed hydraulic systems (coherent with the More Electric Aircraft concept). Furthermore, to evaluate the feasibility of the systems, the study correlates industrial components and aeronautical systems through systematic analogy, resulting in an estimate of the size and weight of digital hydraulic systems if designed for the aeronautical industry. The resulting digital hydraulic systems adhere to the reliability practices and safety standards employed in aircraft flight control while showing similar sizes and weights to the current solutions.
- 28 October 2025
- Published by Linkoping University Electronic Press in Swedish Aerospace Conference, FT2025
- Vol. 215
Open AccessRedundant Digital Hydraulic Actuators for Flight Control Surfaces
The aircraft industry is continually driven to improve energy efficiency in response to environmental concerns and cost reduction. Among solutions available in the field, hydraulics is commonly chosen to deliver crucial functions for its known reliability, precise controllability, and high stiffness. Additionally, when compared to competing technologies in development, hydraulic systems are far less susceptible to jamming, heat rejection problems, and premature wear. In the current context, digital hydraulics emerges as a promising alternative to conventional hydraulics, greatly increasing energy efficiency while keeping the robustness of fluid power systems. Aiming to apply this technology to aircraft systems, this paper introduces enhancements for the digital hydraulic topologies developed at LASHIP/UFSC that allow them to be applied in critical tasks, such as flight control actuation, achieving reliability and performance criteria, beyond the increase in efficiency. These topologies were refined with segregation and independence principles, as is standard in aircraft. The solutions address both centralized (easier to adapt to existing aircraft designs) and distributed hydraulic systems (coherent with the More Electric Aircraft concept). Furthermore, to evaluate the feasibility of the systems, the study correlates industrial components and aeronautical systems through systematic analogy, resulting in an estimate of the size and weight of digital hydraulic systems if designed for the aeronautical industry. The resulting digital hydraulic systems adhere to the reliability practices and safety standards employed in aircraft flight control while showing similar sizes and weights to the current solutions.
- 18 February 2025
- Published by Springer Nature in Meccanica
- Vol. 60 (4) , 723-737
A method for designing digital hydraulic pumps with variable angular speed
- 18 February 2025
- Published by Springer Nature in Meccanica
- Vol. 60 (4) , 723-737
A method for designing digital hydraulic pumps with variable angular speed
- Open Access
- 1 January 2025
- Published by River Publishers
- p. 51-60
Development of a hydraulic supply system with pressurized reservoir for a digital hydraulic actuator
The aviation sector actively pursues enhanced energy efficiency and performance, as these improvements trigger a cascading effect that iteratively reduces system weight and size, ultimately lowering fuel consumption, a priority for minimizing operational costs and addressing environmental concerns. In flight control surface actuation systems, where hydraulics is widely employed for its maturity and reliability, such advancements may translate to reductions in hydraulic pumps and conditioning components, fewer and smaller hydraulic lines (and the fluid mass they contain), smaller heat exchangers, reduced fuel reserves required for thermal management, and minimized leakage risks at connection points. In this context, digital hydraulics has been in development in recent years as a promising approach to significantly improve the energy efficiency of flight control systems while maintaining the reliability critical for the application. This paper presents a hydraulic supply system capable of efficiently delivering three different constant-pressure lines, which can support digital hydraulic actuators under development for aviation and other high-performance systems. Since the technology is intended for aviation, the presented architecture includes a pressurized reservoir obtained through a combination of actuators connected to the reservoir and pump outlet. The proposed supply matches pressure reducing and relief valves together with a pressure-compensated pump and three accumulators to generate and maintain the demanded pressure lines. Via simulations on the Hopsan software, the solution is tested alongside with the digital hydraulic actuator for step and sine position inputs. The pressure lines show little fluctuation and the actuator performs as expected, which indicates that the proposed supply is capable of providing the necessary conditions of operation. The simulated system as a whole (supply and actuator) achieves efficiencies of up to 59%, far greater than the obtained by traditional servo hydraulics, and cavitation is avoided in all times.
- 1 January 2025
- Published by River Publishers
- p. 51-60
Open AccessDevelopment of a hydraulic supply system with pressurized reservoir for a digital hydraulic actuator
The aviation sector actively pursues enhanced energy efficiency and performance, as these improvements trigger a cascading effect that iteratively reduces system weight and size, ultimately lowering fuel consumption, a priority for minimizing operational costs and addressing environmental concerns. In flight control surface actuation systems, where hydraulics is widely employed for its maturity and reliability, such advancements may translate to reductions in hydraulic pumps and conditioning components, fewer and smaller hydraulic lines (and the fluid mass they contain), smaller heat exchangers, reduced fuel reserves required for thermal management, and minimized leakage risks at connection points. In this context, digital hydraulics has been in development in recent years as a promising approach to significantly improve the energy efficiency of flight control systems while maintaining the reliability critical for the application. This paper presents a hydraulic supply system capable of efficiently delivering three different constant-pressure lines, which can support digital hydraulic actuators under development for aviation and other high-performance systems. Since the technology is intended for aviation, the presented architecture includes a pressurized reservoir obtained through a combination of actuators connected to the reservoir and pump outlet. The proposed supply matches pressure reducing and relief valves together with a pressure-compensated pump and three accumulators to generate and maintain the demanded pressure lines. Via simulations on the Hopsan software, the solution is tested alongside with the digital hydraulic actuator for step and sine position inputs. The pressure lines show little fluctuation and the actuator performs as expected, which indicates that the proposed supply is capable of providing the necessary conditions of operation. The simulated system as a whole (supply and actuator) achieves efficiencies of up to 59%, far greater than the obtained by traditional servo hydraulics, and cavitation is avoided in all times.
- 22 June 2023
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 145 (8) , 1-47
A Method for Designing of Hydraulic Actuators Using Digital Hydraulic Pump and Multichamber Cylinder
Hydraulic actuation systems have a broad range of applications covering almost all areas of manufacturing and production and also the service industry. However, it is usual for systems to have low energy efficiency. In recent decades, due to global environmental concerns, research in the field of digital hydraulics to develop more efficient hydraulic systems has increased. In this paper, an analysis of the possible combinations of chambers in a multichamber cylinder is presented. A mathematical expression is derived to verify the total number of combinations of chambers that it is possible to achieve for a cylinder with four or more chambers and that result in different constant velocities without cavitation occurring. In addition, a digital hydraulic pump is considered a supply unit and, since it has discrete output flow rates, an analytical method to combine the pump with a multichamber cylinder is developed resulting in a total number of cylinder velocities with a required resolution. For application in a positioning system, design guidelines for an actuator using a cylinder with four chambers and a digital hydraulic pump with three fixed displacement units are presented in which an optimization algorithm for the calculation of the cylinder areas and the volumetric displacement of the pumps is applied. The proposed approaches were applied to design a proof-of-concept and the experimental values presented very good accuracy when compared with the results obtained with the model. Closed-loop position control responses show that the system can achieve the required setting time with a smooth movement and steady-state error of around 1 mm.
- 22 June 2023
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 145 (8) , 1-47
A Method for Designing of Hydraulic Actuators Using Digital Hydraulic Pump and Multichamber Cylinder
Hydraulic actuation systems have a broad range of applications covering almost all areas of manufacturing and production and also the service industry. However, it is usual for systems to have low energy efficiency. In recent decades, due to global environmental concerns, research in the field of digital hydraulics to develop more efficient hydraulic systems has increased. In this paper, an analysis of the possible combinations of chambers in a multichamber cylinder is presented. A mathematical expression is derived to verify the total number of combinations of chambers that it is possible to achieve for a cylinder with four or more chambers and that result in different constant velocities without cavitation occurring. In addition, a digital hydraulic pump is considered a supply unit and, since it has discrete output flow rates, an analytical method to combine the pump with a multichamber cylinder is developed resulting in a total number of cylinder velocities with a required resolution. For application in a positioning system, design guidelines for an actuator using a cylinder with four chambers and a digital hydraulic pump with three fixed displacement units are presented in which an optimization algorithm for the calculation of the cylinder areas and the volumetric displacement of the pumps is applied. The proposed approaches were applied to design a proof-of-concept and the experimental values presented very good accuracy when compared with the results obtained with the model. Closed-loop position control responses show that the system can achieve the required setting time with a smooth movement and steady-state error of around 1 mm.