Xuejiao Cao

Aiming at the bottleneck of the difficult scrubbing and separation of scandium and titanium in the solvent extraction process for scandium recovery, a novel strategy for scandium–titanium separation via citrate complex scrubbing is proposed based on the difference in complexation properties between scandium/titanium and hydroxycarboxylic acids. The mixed Na₃Cit + H₂O₂ system was screened as the optimal scrubbing agent. The effects of key parameters including dosages of Na₃Cit and H₂O₂ and phase ratio (O/A) on scrubbing performance were systematically investigated. The optimal process conditions were determined as follows: temperature of 25 °C, molar ratio n(Na₃Cit)/n(Ti) = 30:1, molar ratio n(H₂O₂)/n(Ti) = 3:1, phase ratio (O/A) of 1:1, shaking speed of 200 r/min, and scrubbing time of 30 min. Under the optimal conditions, the titanium scrubbing efficiency reaches 97.37% with zero co-scrubbing efficiency of scandium. The separation efficiency is 14.47 times higher than that of the conventional H₂SO₄ + H₂O₂ scrubbing system, which significantly enhances the scandium–titanium separation performance. This work provides a feasible technical route for the deep separation and purification of scandium and titanium from titanium white waste acid.

The diaspore is a typical representative of bauxite resources in China, which is the primary raw material for the Bayer process in alumina production, particularly in regions such as Shanxi, Guangxi, Guizhou, and Henan. Clarifying the phase transformations and reaction mechanisms of the silicon-containing minerals during the Bayer leaching process of diaspore is essential for improving the efficiency of alumina production. This article focuses on montmorillonite, which is one of the silicon-containing minerals of diaspore-type bauxite, investigating the reaction mechanisms and phase changes of montmorillonite under the high-calcium sodium aluminate solution system by using X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Magic Angle Spinning Nuclear Magnetic Resonance (MAS–NMR) and Fourier Transform Infrared Spectroscopy (FTIR). The results show that montmorillonite dissolved and transformed into Na₆(AlSiO₄)₆ (hydrated sodium aluminosilicate) under the high-calcium sodium aluminate solution system, and calcium oxide and sodium aluminate in the solution reacted to form (CaO)₃Al₂O₃(H₂O)₆ (hydrated calcium aluminate). With the increase of reaction temperature, caustic alkali concentration (N_k), and reaction time, hydrated calcium aluminate and hydrated sodium aluminosilicate react and transform into Ca₃Al₂SiO₄(OH)₈ (hydrogarnet). Under the optimal reaction conditions of a 120 min reaction time, a temperature of 240 °C, an N_k of 240 g/L, and a CaO–to–SiO₂ mass ratio (C/S) of 3.5:1, the montmorillonite reaction degree can reach a maximum of 93.71%.

In view of the current situation wherein acid resources and valuable components in titanium dioxide waste acid cannot be effectively extracted and are prone to secondary pollution, our research team proposed a new technique consisting of step extraction and the comprehensive utilization of titanium dioxide waste acid. In this paper, the thermodynamics of selective precipitation and the preparation of doped iron phosphate from waste acid were studied. The thermodynamics results show that the content of Al³⁺, Mn²⁺, Mg²⁺, and Ca²⁺ in the reaction system can be tuned by adjusting the pH during the pre-precipitation process. In the first step, these impurity ions should be settled as much as possible; then, Fe²⁺ should be oxidized to Fe³⁺ so as to obtain iron phosphate with higher purity in the next step of the precipitation process. The effects of the reaction temperature, seed crystals, pH value, and P/M on the precipitation process were investigated in detail. The experimental results show that in the reduced state, the optimal precipitation conditions are a temperature of 75 °C, an initial pH value of 4.5, and an optimal P/M molar ratio of 1.1. In the oxidized state, the optimal precipitation conditions are a temperature of 60 °C, a solution pH = 2.5, and a reaction time of 25 min. After calcination, the precipitate mainly consists of iron phosphate, which basically meets the requirements of an iron phosphate precursor.

In recent years, the rapid development of the domestic alumina industry has greatly accelerated the consumption of high-alumina–silica-ratio bauxite resources in China. The development of an efficient and clean utilization technology applicable to low-grade bauxite in China is not only a requirement for resource and environmental protection, but also a powerful guarantee to maintain the sustainable development of China’s aluminum industry. Based on this, the authors’ team proposed a new process for the treatment of low-grade bauxite ore via a calcification–carbonization method from the perspective of equilibrium solid-phase reconstruction and achieved the first industrial-scale trial run on the basis of existing laboratory research. The results show that the mass fraction of Na₂O in bauxite residue can be reduced to 0.95% in the treatment of typical diaspore bauxite, the A/S in the bauxite residue can be reduced to 0.85 after two-time carbonization–alumina dissolution, and the actual alumina dissolution rate can reach 81.32%. The relevant results verified the feasibility and advantages of the calcification–carbonization method in industrial production.