Yan Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yan Xu has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
- Jianping Zhou
School of Mechanical Engineering, Xinjiang University, Urumqi 830047, China
11 shared publications Yutong Chen
Xinjiang University
8 shared publicationsJianping Zhou
5 shared publicationsZhitao Yin
School of Intelligent Manufacturing Modern Industry School of Mechanical Engineering
5 shared publicationsBingbing Wang
4 shared publicationsGuang Yang
College of Mechanical Engineering
3 shared publications
Latest Publications
- 10 November 2026
- Published by American Chemical Society (ACS) in ACS Applied Bio Materials
3D-Printed OsteoFlux Scaffolds with Radially Graded TPMS Structures
In native bone, the transition from dense cortical bone to porous cancellous bone reflects a spatial coordination between mechanical support and mass transport. Inspired by this structural heterogeneity, this study proposes an OsteoFlux (OF) scaffold featuring a radially graded TPMS structure together with a corresponding 3D printing strategy. Specifically, a biomimetic TPMS scaffold design integrating a continuous pore-size gradient with an explicit gradient position constraint was developed. Fluid–structure interaction (FSI) simulations investigating the effects of TPMS topology and gradient parameters on scaffold mechanical and transport performance were performed. The results indicated that the OF scaffold (a Gyroid (G-type) scaffold with an 800–400 μm radial pore-size gradient) achieved the most favorable combination of mechanical stability and fluid transport performance. Finally, an experiment optimizing the BCP slurry system and digital light processing (DLP) printing parameters was conducted. The fabricated OF scaffold exhibited a compressive strength of 3.25 MPa, a compressive modulus of 172.55 MPa, and a permeability of 4.17 × 10–9 m2. In vitro biological evaluation demonstrated favorable cytocompatibility, along with enhanced osteogenic differentiation and matrix mineralization of mBMSCs under scaffold-conditioned culture conditions. These findings demonstrate that the proposed OF scaffold provides an effective strategy for enhancing the overall performance of porous ceramic scaffolds.
- 10 November 2026
- Published by American Chemical Society (ACS) in ACS Applied Bio Materials
3D-Printed OsteoFlux Scaffolds with Radially Graded TPMS Structures
In native bone, the transition from dense cortical bone to porous cancellous bone reflects a spatial coordination between mechanical support and mass transport. Inspired by this structural heterogeneity, this study proposes an OsteoFlux (OF) scaffold featuring a radially graded TPMS structure together with a corresponding 3D printing strategy. Specifically, a biomimetic TPMS scaffold design integrating a continuous pore-size gradient with an explicit gradient position constraint was developed. Fluid–structure interaction (FSI) simulations investigating the effects of TPMS topology and gradient parameters on scaffold mechanical and transport performance were performed. The results indicated that the OF scaffold (a Gyroid (G-type) scaffold with an 800–400 μm radial pore-size gradient) achieved the most favorable combination of mechanical stability and fluid transport performance. Finally, an experiment optimizing the BCP slurry system and digital light processing (DLP) printing parameters was conducted. The fabricated OF scaffold exhibited a compressive strength of 3.25 MPa, a compressive modulus of 172.55 MPa, and a permeability of 4.17 × 10–9 m2. In vitro biological evaluation demonstrated favorable cytocompatibility, along with enhanced osteogenic differentiation and matrix mineralization of mBMSCs under scaffold-conditioned culture conditions. These findings demonstrate that the proposed OF scaffold provides an effective strategy for enhancing the overall performance of porous ceramic scaffolds.
- Open Access
- 1 November 2026
- Published by Elsevier in Smart Agricultural Technology
- Vol. 15
DALF-YOLO: Cherry tomato ripeness detection in complex environments via frequency-domain dynamic attention and local-global multiscale fusion
- 1 November 2026
- Published by Elsevier in Smart Agricultural Technology
- Vol. 15
Open AccessDALF-YOLO: Cherry tomato ripeness detection in complex environments via frequency-domain dynamic attention and local-global multiscale fusion
- 9 September 2026
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 41 (12) , 1743-1752
Low-voltage micro-arc discharge-grinding process optimization for GH4169
GH4169, a nickel-based superalloy, is widely used in key components such as aero-engines because of its high-temperature strength and resistance to oxidation and corrosion.[1] However, its low ther...
- 9 September 2026
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 41 (12) , 1743-1752
Low-voltage micro-arc discharge-grinding process optimization for GH4169
GH4169, a nickel-based superalloy, is widely used in key components such as aero-engines because of its high-temperature strength and resistance to oxidation and corrosion.[1] However, its low ther...
- Open Access
- 13 August 2026
- Published by Wiley in Advanced Functional Materials
- p. e77610
Intrinsic Environmental Referencing in Coaxial Nanofiber Yarns Enables Humidity‐Robust Triboelectric Tactile Recognition
Triboelectric tactile sensors coupled with machine learning achieve high material recognition accuracy under controlled conditions, but ambient humidity introduces a domain shift that degrades performance in real‐world settings. Here we develop a coaxial porous nanofiber sensing yarn that embeds environmental referencing directly within its sensing structure. The yarn combines triboelectric material recognition with a capacitive baseline ( C 0 ) whose monotonic humidity dependence serves as an intrinsic environmental indicator, co‐localized and temporally synchronized with the sensing signal. Using C 0 to partition data into humidity‐defined bins, a humidity‐adaptive learning framework recovers cross‐humidity classification accuracy from 70.2% to 95.7% without external sensors. The capacitive mode simultaneously provides pressure sensitivity enhanced approximately to 2.74 times over dense‐coated yarns, stability over 6000 cycles, ultralight‐object detection, and stiffness discrimination. Integrated into a soft robotic gripper, a gated multimodal fusion network achieves 99.9% classification accuracy across five object categories and 30‐70% relative humidity. This work shows that environmental sensitivity in sensing systems, rather than being an obstacle to suppress, can serve as an intrinsic information source for adaptive perception.
- 13 August 2026
- Published by Wiley in Advanced Functional Materials
- p. e77610
Open AccessIntrinsic Environmental Referencing in Coaxial Nanofiber Yarns Enables Humidity‐Robust Triboelectric Tactile Recognition
Triboelectric tactile sensors coupled with machine learning achieve high material recognition accuracy under controlled conditions, but ambient humidity introduces a domain shift that degrades performance in real‐world settings. Here we develop a coaxial porous nanofiber sensing yarn that embeds environmental referencing directly within its sensing structure. The yarn combines triboelectric material recognition with a capacitive baseline ( C 0 ) whose monotonic humidity dependence serves as an intrinsic environmental indicator, co‐localized and temporally synchronized with the sensing signal. Using C 0 to partition data into humidity‐defined bins, a humidity‐adaptive learning framework recovers cross‐humidity classification accuracy from 70.2% to 95.7% without external sensors. The capacitive mode simultaneously provides pressure sensitivity enhanced approximately to 2.74 times over dense‐coated yarns, stability over 6000 cycles, ultralight‐object detection, and stiffness discrimination. Integrated into a soft robotic gripper, a gated multimodal fusion network achieves 99.9% classification accuracy across five object categories and 30‐70% relative humidity. This work shows that environmental sensitivity in sensing systems, rather than being an obstacle to suppress, can serve as an intrinsic information source for adaptive perception.
- Open Access
Calibration and Experimental Validation of Discrete Element Parameters for Cotton Stalk Phloem, Xylem and Pith
The xylem of cotton stalks is a high-quality biomass feedstock with strong high-value utilization potential. However, existing studies lack accurate calibration of discrete-element parameters for separated stalk components, which limits the optimization of the design of separation equipment. This study uses phloem, xylem, and pith of cotton stalks as research objects and measures the intrinsic physical and mechanical parameters and paired contact parameters of the three components. Given the strong agglomeration tendency of crushed phloem long fibers, the Hertz–Mindlin with JKR model is used to calibrate the adhesion parameter. The applicability of this model to low-moisture, high-aspect-ratio fibrous materials is verified, and the measured equivalent surface energy of phloem reaches 2.887 J/m2. CFD-DEM-coupled air separation verification is performed. The relative errors of xylem impurity content and loss rate between simulation and experiment are both below 10%, confirming the good reliability of the calibrated parameters. This study provides data to support the development of cleaning equipment for crushed cotton stalks. It provides a methodological reference for calibrating discrete-element parameters for similar long-fiber biomass materials.
Open AccessCalibration and Experimental Validation of Discrete Element Parameters for Cotton Stalk Phloem, Xylem and Pith
The xylem of cotton stalks is a high-quality biomass feedstock with strong high-value utilization potential. However, existing studies lack accurate calibration of discrete-element parameters for separated stalk components, which limits the optimization of the design of separation equipment. This study uses phloem, xylem, and pith of cotton stalks as research objects and measures the intrinsic physical and mechanical parameters and paired contact parameters of the three components. Given the strong agglomeration tendency of crushed phloem long fibers, the Hertz–Mindlin with JKR model is used to calibrate the adhesion parameter. The applicability of this model to low-moisture, high-aspect-ratio fibrous materials is verified, and the measured equivalent surface energy of phloem reaches 2.887 J/m2. CFD-DEM-coupled air separation verification is performed. The relative errors of xylem impurity content and loss rate between simulation and experiment are both below 10%, confirming the good reliability of the calibrated parameters. This study provides data to support the development of cleaning equipment for crushed cotton stalks. It provides a methodological reference for calibrating discrete-element parameters for similar long-fiber biomass materials.
- 20 July 2026
- Published by Taylor & Francis in Computer Methods in Biomechanics and Biomedical Engineering
- p. 1-14
Study on the parametric design and mechanical permeability properties of radially graded biomimetic disordered skeletal scaffolds
1. The repair of bone defects remains a clinical challenge (Jiang et al. 2025). Among existing treatment methods, the innovative development of artificial bone represents a new solution (Tang et al...
- 20 July 2026
- Published by Taylor & Francis in Computer Methods in Biomechanics and Biomedical Engineering
- p. 1-14
Study on the parametric design and mechanical permeability properties of radially graded biomimetic disordered skeletal scaffolds
1. The repair of bone defects remains a clinical challenge (Jiang et al. 2025). Among existing treatment methods, the innovative development of artificial bone represents a new solution (Tang et al...
- Open Access
- 8 July 2026
- Published by MDPI AG in Agriculture
- Vol. 16 (14) , 1492
Calibration and Experimental Validation of Discrete Element Model Parameters for Cotton Stalks and Cotton Residues Mixture
Accurate discrete element simulation parameters for the mechanically harvested cotton stalks and cotton residues mixture are currently unavailable. This lack hinders the effective design and optimization of equipment for separating and recovering cotton residues from the mixture. This study focused on the cotton stalks and cotton residues mixture. The intrinsic parameters of cotton residues were measured through physical experiments. Using the inclined plane and collision methods, the coefficients of restitution for cotton residues–cotton stalks and cotton residues–steel were determined to be 0.228 and 0.364, respectively. The corresponding static friction coefficients were 0.632 and 0.266, and the rolling friction coefficients were 0.199 and 0.156. The Hertz–Mindlin with JKR contact model was employed. Combined with repose angle tests, the coefficient of restitution, rolling friction coefficient, static friction coefficient, and surface energy for cotton residues–cotton residues were calibrated as 0.393, 0.140, 0.742, and 1.471 J/m2, respectively. A vibrating spreading test was conducted to validate the calibrated parameters. The proportion of cotton residues on the material surface was used as the test index. The mean relative error between simulation and physical test results under four working conditions was 4.91%. The results indicate that acceptable consistency is achieved between simulation and experimental results under the tested conditions, and the calibrated discrete element parameters are applicable for the simulation of cotton stalk–cotton residue mixture systems. This study provides a theoretical basis and data support for the development of equipment to separate and recover cotton residues from cotton stalk and cotton residue mixtures.
- 8 July 2026
- Published by MDPI AG in Agriculture
- Vol. 16 (14) , 1492
Open AccessCalibration and Experimental Validation of Discrete Element Model Parameters for Cotton Stalks and Cotton Residues Mixture
Accurate discrete element simulation parameters for the mechanically harvested cotton stalks and cotton residues mixture are currently unavailable. This lack hinders the effective design and optimization of equipment for separating and recovering cotton residues from the mixture. This study focused on the cotton stalks and cotton residues mixture. The intrinsic parameters of cotton residues were measured through physical experiments. Using the inclined plane and collision methods, the coefficients of restitution for cotton residues–cotton stalks and cotton residues–steel were determined to be 0.228 and 0.364, respectively. The corresponding static friction coefficients were 0.632 and 0.266, and the rolling friction coefficients were 0.199 and 0.156. The Hertz–Mindlin with JKR contact model was employed. Combined with repose angle tests, the coefficient of restitution, rolling friction coefficient, static friction coefficient, and surface energy for cotton residues–cotton residues were calibrated as 0.393, 0.140, 0.742, and 1.471 J/m2, respectively. A vibrating spreading test was conducted to validate the calibrated parameters. The proportion of cotton residues on the material surface was used as the test index. The mean relative error between simulation and physical test results under four working conditions was 4.91%. The results indicate that acceptable consistency is achieved between simulation and experimental results under the tested conditions, and the calibrated discrete element parameters are applicable for the simulation of cotton stalk–cotton residue mixture systems. This study provides a theoretical basis and data support for the development of equipment to separate and recover cotton residues from cotton stalk and cotton residue mixtures.
- Open Access
- 30 June 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 43, 3325-3339
Regulating thermochemical erosion to achieve high-cleanliness surfaces on C/SiC composites: Mechanisms of gas-medium assisted electric arc machining
- 30 June 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 43, 3325-3339
Open AccessRegulating thermochemical erosion to achieve high-cleanliness surfaces on C/SiC composites: Mechanisms of gas-medium assisted electric arc machining
- Open Access
- 14 June 2026
- Published by Elsevier in Materials & Design
- Vol. 267
Low-voltage micro-arc discharge-grinding hybrid machining: Discharge energy regulation for high-surface-quality machining of Inconel 718
- 14 June 2026
- Published by Elsevier in Materials & Design
- Vol. 267
Open AccessLow-voltage micro-arc discharge-grinding hybrid machining: Discharge energy regulation for high-surface-quality machining of Inconel 718
- 9 April 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (14) , 25582-25596
Electrical arc machining mechanisms in C/SiC composites: Coupled effects of conductivity contrast and weaving architecture
- 9 April 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (14) , 25582-25596
Electrical arc machining mechanisms in C/SiC composites: Coupled effects of conductivity contrast and weaving architecture