Kangning Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kangning Liu has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Gaoshen Cai
School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China
2 shared publications - Jubo Fu
Faculty of Mechanical Engineering & Automation, Zhejiang Sci-Tech University, Hangzhou 310018, China
2 shared publications Lang Lihui
School of Mechanical Engineering and Automation, Beihang University, Beijing, China
2 shared publications- Lihui Lang
School of Mechanical Engineering and Automation, Beihang University, Beijing 100191, China
2 shared publications - Biao Hu
School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China
1 shared publication Chan Guo
School of Mechanical Engineering and Automation, Beihang University, Beijing 100191, China
1 shared publication
Latest Publications
- 25 May 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 238 (4) , 524-537
Modeling of constitutive behavior and ductile fracture of AA5A06 aluminum alloy sheet in warm hydroforming process
In order to predict the formability of lightweight materials, the flow stress and fracture behavior of AA5A06 aluminum alloy which is very sensitive to temperature and strain-rate were investigated in this study. First, a modified Misiolek constitutive equation with a work-soften term is proposed to calculate the flow stress of the sheet metal. To predict ductile fracture in sheet forming operations, Cockcroft-Latham damage criterion is applied here and ductile fracture threshold under each condition is estimated using Response Surface Method. Finally, warm hydroforming deep drawing tests were conducted at various conditions and the experiment results are compared with the numerical simulation result to evaluate the new model’s feasibility and accuracy in forecasting the mechanical response of the material in warm forming conditions. Results show that the proposed model has a good accuracy compared with the traditional power law models and the FEM simulation conforms well to the tests.
- 25 May 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 238 (4) , 524-537
Modeling of constitutive behavior and ductile fracture of AA5A06 aluminum alloy sheet in warm hydroforming process
In order to predict the formability of lightweight materials, the flow stress and fracture behavior of AA5A06 aluminum alloy which is very sensitive to temperature and strain-rate were investigated in this study. First, a modified Misiolek constitutive equation with a work-soften term is proposed to calculate the flow stress of the sheet metal. To predict ductile fracture in sheet forming operations, Cockcroft-Latham damage criterion is applied here and ductile fracture threshold under each condition is estimated using Response Surface Method. Finally, warm hydroforming deep drawing tests were conducted at various conditions and the experiment results are compared with the numerical simulation result to evaluate the new model’s feasibility and accuracy in forecasting the mechanical response of the material in warm forming conditions. Results show that the proposed model has a good accuracy compared with the traditional power law models and the FEM simulation conforms well to the tests.
- 24 September 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 118 (5-6) , 1933-1940
Investigation on granular medium forming formability of TA1 titanium alloy cylinder-shaped parts
- 24 September 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 118 (5-6) , 1933-1940
Investigation on granular medium forming formability of TA1 titanium alloy cylinder-shaped parts
- Open Access
Simulation and Experimental Investigation of Granular Medium Forming Technology on Titanium Alloy Sheet at 500 °C
To investigate and verify the degree to which the forming properties of low plasticity materials are improved at room temperature using the granular medium forming (GMF) process at 500 °C, a coupled Eulerian–Lagrangian unit calculation model was established and a special mold was designed to conduct a GMF experiment for titanium alloy sheets under different-shaped pressing blocks. Then, using a three-coordinate measuring machine, the sizes of the outer contours of the parts formed at room temperature were measured, and the results showed that the bottom of the parts maintained a smooth surface during the drawing process. As the drawing height increased, the radius of curvature of the cambered surface gradually decreased. By measuring the wall thickness of the parts at different positions from the central axis using a caliper, the wall thickness distribution curves of these parts were obtained, which showed that the deformations of the bottom of the formed parts were uniform and the uniformity of the wall thickness distribution was good. By comparing the GMF experimental data at 500 °C with traditional deep drawing experimental data, it was found that the GMF technology could improve the forming properties of low plastic materials such as titanium alloys.
Open AccessSimulation and Experimental Investigation of Granular Medium Forming Technology on Titanium Alloy Sheet at 500 °C
To investigate and verify the degree to which the forming properties of low plasticity materials are improved at room temperature using the granular medium forming (GMF) process at 500 °C, a coupled Eulerian–Lagrangian unit calculation model was established and a special mold was designed to conduct a GMF experiment for titanium alloy sheets under different-shaped pressing blocks. Then, using a three-coordinate measuring machine, the sizes of the outer contours of the parts formed at room temperature were measured, and the results showed that the bottom of the parts maintained a smooth surface during the drawing process. As the drawing height increased, the radius of curvature of the cambered surface gradually decreased. By measuring the wall thickness of the parts at different positions from the central axis using a caliper, the wall thickness distribution curves of these parts were obtained, which showed that the deformations of the bottom of the formed parts were uniform and the uniformity of the wall thickness distribution was good. By comparing the GMF experimental data at 500 °C with traditional deep drawing experimental data, it was found that the GMF technology could improve the forming properties of low plastic materials such as titanium alloys.
- Open Access
- 12 August 2014
- Published by EDP Sciences in Manufacturing Review
- Vol. 1, 9
A critical review on special forming processes and associated research for lightweight components based on sheet and tube materials
Lightweight materials, such as ultra-high strength steel, titanium alloys and aluminum alloys, are used widely in aerospace and automobile industries leading to increasing demands for advanced forming technologies. Recently many innovative sheet- and tube-forming methods have been proposed by researchers and R&D facilities around the word. These methods can greatly improve the formability of materials with low plasticity and can produce complex-shaped parts with good surface qualities. This review aims at providing an insight into the latest developments of particular sheet- or tubular-metal forming process and shows basic applications in modern industry.
- 12 August 2014
- Published by EDP Sciences in Manufacturing Review
- Vol. 1, 9
Open AccessA critical review on special forming processes and associated research for lightweight components based on sheet and tube materials
Lightweight materials, such as ultra-high strength steel, titanium alloys and aluminum alloys, are used widely in aerospace and automobile industries leading to increasing demands for advanced forming technologies. Recently many innovative sheet- and tube-forming methods have been proposed by researchers and R&D facilities around the word. These methods can greatly improve the formability of materials with low plasticity and can produce complex-shaped parts with good surface qualities. This review aims at providing an insight into the latest developments of particular sheet- or tubular-metal forming process and shows basic applications in modern industry.