Rajakumar S. Rai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Rajakumar S. Rai has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Anshuman Kumar Sahu
IDMEC, Instituto Superior Tecnico, Universidade de Lisboa, Lisboa, Portugal
1 shared publication - Arumugam Eakambaram
B.S. Abdur Rahman Crescent Institute of Science and Technology
1 shared publication - D. Rajeev
Department of Mechanical Engineering, Mar Ephraem College of Engineering and Technology, Tamilnadu, India
1 shared publication - Deepankar Panda
Natl Inst Technol Rourkela, Dept Met & Mat Engn, Rourkela 769008, Odisha, India
1 shared publication Hridayjit Kalita
Department of Mechanical Engineering, Birla Institute of Technology Mesra, Ranchi, India
1 shared publicationI. Kantharaj
Department of Mechanical Engineering, Karunya Institute of Technology and Sciences, Coimbatore, Tamil Nadu, India
1 shared publication
Latest Publications
- 24 January 2025
- Published by SAGE Publications in Tribology - Materials, Surfaces & Interfaces
- Vol. 19 (1) , 39-53
Development of cost-effective, high-performance ceramic-metallic brake pads for agricultural tractors
A cerametallic friction pad (CMDE) was developed through the Powder metallurgy route and validated through a classical SAEJ 661 standard laboratory test (Chase Testing machine) followed by the field test. The same was compared with an imported OE (CMOE) pad. In the chase test, CMDE fared poorly in fade-1 by 25% concerning the reference value but fulfilled the fade-II and recovery characteristics. From a wear viewpoint, the specific wear rate of CMDE and CMOE are marginally close. Considering the wear in the field test, CMDE has shown 11.1% more wear than CMOE, but 20% less wear in the mating part. More reduction in the surface roughness of CMDE after the field test evidenced its engagement characteristics by deforming asperities. Adhesive wear scoring marks were visible along the sliding direction of the pressure plate and the sintered friction pad. Thus, CMDE has the potential to replace CMOE in performance and cost
- 24 January 2025
- Published by SAGE Publications in Tribology - Materials, Surfaces & Interfaces
- Vol. 19 (1) , 39-53
Development of cost-effective, high-performance ceramic-metallic brake pads for agricultural tractors
A cerametallic friction pad (CMDE) was developed through the Powder metallurgy route and validated through a classical SAEJ 661 standard laboratory test (Chase Testing machine) followed by the field test. The same was compared with an imported OE (CMOE) pad. In the chase test, CMDE fared poorly in fade-1 by 25% concerning the reference value but fulfilled the fade-II and recovery characteristics. From a wear viewpoint, the specific wear rate of CMDE and CMOE are marginally close. Considering the wear in the field test, CMDE has shown 11.1% more wear than CMOE, but 20% less wear in the mating part. More reduction in the surface roughness of CMDE after the field test evidenced its engagement characteristics by deforming asperities. Adhesive wear scoring marks were visible along the sliding direction of the pressure plate and the sintered friction pad. Thus, CMDE has the potential to replace CMOE in performance and cost
- Open Access
- 1 January 2023
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2023 (1)
Artificial Neural Network on Tool Condition Monitoring in Hard Turning of AISI4140 Steel Using Carbide Tool
Hard turning has replaced conventional grinding in production processes in recent years as an emerging technique. Nowadays, coated carbide tools are replacing expensive CBN inserts in turning. Wear is a significant concern when turning with coated carbide; it immediately affects the acceptability of the machined surface, which causes machine downtime and loss due to wastage in machined parts. Online tool condition monitoring (TCM) is required to prevent such critical conditions. Hard turning differs from conventional turning in energy balance during metal cutting, resulting in greater thrust force; hence, the TCM model presented for conventional turning may not be suitable for hard turning. Hence, tool wear prediction for turning is projected based on thrust force using an artificial neural network (ANN). All of the tests were done using a design of experiments called full factorial design (FFD). The specimens were made of AISI 4140 steel that had been hardened to 47 HRC, and the inserts were made of coated carbide. The most impactful input features for wear, selected based on experimental outputs, were given to the neural network and trained. Tool wear is an estimated output from the training set that has been validated with satisfactory results for random conditions. The 5–10–1 network structure with the Levenberg–Marquardt (LM) learning algorithm, R2 values of 0.996602 and 0.969437 for the training and testing data, and mean square error values of 0.000133152 and 0.004443 for the training and testing data, respectively, gave the best results. The MEP values of 0.575407 and 2.977617 are very low (5%). The LM learning algorithm‐based ANN is good at predicting tool wear based on how well it predicts tool wear for both the testing set and the training set.
- 1 January 2023
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2023 (1)
Open AccessArtificial Neural Network on Tool Condition Monitoring in Hard Turning of AISI4140 Steel Using Carbide Tool
Hard turning has replaced conventional grinding in production processes in recent years as an emerging technique. Nowadays, coated carbide tools are replacing expensive CBN inserts in turning. Wear is a significant concern when turning with coated carbide; it immediately affects the acceptability of the machined surface, which causes machine downtime and loss due to wastage in machined parts. Online tool condition monitoring (TCM) is required to prevent such critical conditions. Hard turning differs from conventional turning in energy balance during metal cutting, resulting in greater thrust force; hence, the TCM model presented for conventional turning may not be suitable for hard turning. Hence, tool wear prediction for turning is projected based on thrust force using an artificial neural network (ANN). All of the tests were done using a design of experiments called full factorial design (FFD). The specimens were made of AISI 4140 steel that had been hardened to 47 HRC, and the inserts were made of coated carbide. The most impactful input features for wear, selected based on experimental outputs, were given to the neural network and trained. Tool wear is an estimated output from the training set that has been validated with satisfactory results for random conditions. The 5–10–1 network structure with the Levenberg–Marquardt (LM) learning algorithm, R2 values of 0.996602 and 0.969437 for the training and testing data, and mean square error values of 0.000133152 and 0.004443 for the training and testing data, respectively, gave the best results. The MEP values of 0.575407 and 2.977617 are very low (5%). The LM learning algorithm‐based ANN is good at predicting tool wear based on how well it predicts tool wear for both the testing set and the training set.
- 1 January 2021
- Published by Elsevier
Contributors