SFSvitlana Fedchenko

Svitlana Fedchenko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Svitlana Fedchenko has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Method of rational use of excess thermal energy of mining cogeneration power plants

    by Viktor Kostenko, Olha Bohomaz, Oleksii Kutniashenko, Stanislav Sidnei, Tetiana Kostenko, Svitlana Fedchenko, Eduard Drahonenko

    The object of research is the heat flows of hot gases and liquids generated during the operation of the energy source of a mine-based cogeneration power plant (CPP). The subject of research is the methods and means of utilizing the CPP's thermal energy for the demineralization of mine wastewater. The research addresses the problem of inefficient thermal energy utilization during the operation of mine-based cogeneration power plants during periods of minimal thermal load. It was established that, during the warm season, a significant portion of the generated thermal energy finds no useful application and is lost. This results in a drop in the CPP's overall efficiency from 90% to less than 55%. Such data indicate the inefficient use of significant energy potential that could otherwise be harnessed for other technological processes. An improvement to the plant's design is proposed by incorporating a subsystem for the evaporation and condensation of mine wastewater; this allows for the efficient use of thermal energy from exhaust gases and turbocharger gases of diesel engines during the warm season. Implementing the proposed solution enables the conversion of otherwise wasted thermal energy into additional useful products: demineralized water, steam condensation heat, and concentrated salt residues. Calculations determined that the thermal power of the exhaust gases from a single JMS-620 diesel engine is sufficient to drive the water evaporation process across a total surface area of approximately 40 m2 and yield at least 28.8 m3 of demineralized water per day. The use of seasonal surplus thermal energy to produce demineralized water from wastewater can be implemented not only at mine-based CPPs but also at cogeneration facilities in other sector, such as biogas and metallurgical plant, and within district heating systems.

  • Open Access

    Improvement of the experimental-calculation method for assessing the fire resistance of tubular concrete columns of circular cross-section

    by Serhii Pozdieiev, Svitlana Fedchenko, Ihor Fedchenko, Andrii Kovalov, Taras Shnal, Serhii Strikha, Andrii Shvydenko, Olga Shynkarenko

    This paper investigates processes of heat transfer in the cross-section of tubular concrete columns of circular cross-section when assessing their fire resistance. The task addressed is to determine temperature distribution in the cross-section of tubular concrete columns using a limited number of experimental measurements. The result is the refined method for deriving the temperature value at any point of the cross-section of tubular concrete columns, based on the results from measuring temperature indicators at individual points of the cross-section during fire tests. The resulting temperature data are part of the initial data for solving the strength problem in the calculated assessment of fire resistance. The study showed that a simple analytical expression could be used to carry out the interpolation procedure. This expression was constructed based on the approximation of temperature distribution in the radial direction by a parabolic dependence. The temperature data obtained using the improved interpolation procedure were used to construct deformation diagrams for the sections of the cross-section corresponding to concrete and steel cage, into which the cross-section of the tubular concrete column is divided. The adequacy and accuracy of the resulting data obtained using the proposed interpolation procedure algorithm were demonstrated by comparing them with the data obtained by solving the thermal conductivity problem; the error is on average 4.6%. The improved experimental and computational method was tested using experimental data on temperature measurements from fire tests of the tubular concrete column for fire resistance. The resulting fire resistance limit was 105 min, in contrast to the experimentally obtained one of 115 min. The adequacy and accuracy of the results have been proven as the error in determining the fire resistance limit does not exceed 9%

  • Open Access

    Determining the behavior of a glass panel under heating conditions during a fire

    by Valeriia Nekora, Serhii Pozdieiev, Olga Nekora, Svitlana Fedchenko, Vadym Nizhnyk, Alina Novhorodchenko, Taras Shnal

    The object of this study is the processes of heating and destruction of glazing in translucent elements of fencing structures. The paper provides data on the computer simulation of a glass panel behavior when it is heated on one side under the conditions of exposure to the standard fire temperature regime. With the help of computer simulation of a glass panel under conditions of thermal influence, the process of heat transfer was reproduced based on the non-stationary heat conduction equation. The stress-strain state of the glass panel was considered using the finite element method. The thermal effect was combined with the mechanical load due to the excess pressure that can occur in the room where the fire originates and develops. To study the propagation of cracks in glass, the strength criterion according to the Johnson-Holmquist model was applied. As a result of computer simulation based on a mathematical model, data were obtained on the dynamics of the formation and propagation of cracks in a glass panel under conditions of heating according to the standard fire temperature regime. It is shown that the glass panel is destroyed through the formation of a system of branched cracks, which is confirmed by empirical experience. The destruction of the glass panel was associated with the onset of the limit state of loss of integrity, and its fire resistance limit was registered based on this attribute. In the work, a comparative analysis of the obtained data with the findings from experimental studies has been carried out. As a result of the comparative analysis, it is shown that the results are adequate since their relative error is on average no more than 8 %, and the F-criterion of adequacy at the significance level of 0.05 does not exceed the tabular value. Based on the results, the possibility of its application for a reliable analysis of the fire resistance of enclosing elements in building structures has been proven


  • Open Access

    RESEARCH ON THE BEHAVIOR OF STEEL-CONCRETE COLUMNSIN FIRE CONDITIONS

    by Ihor Fedchenko, Svitlana Fedchenko, Ігор Федченко

    Steel-concrete is a composite material that combines the high strength of steel with the ductility of concrete. This synergy results in improved performance characteristics, particularly for structures subjected to significant static or dynamic loads under fire conditions.In modern construction, steel-concrete composite structures have considerable potential,especially in the design of high-rise buildings, bridges, industrial facilities, as well as in post-conflict reconstruction of damaged infrastructure. The combination of steel frame elements and concrete infill not only reduces the size of structural components but also increases their durability, load-bearing capacity, and fire resistance.The aim of this article is to investigate the behavior of steel-concrete columns under standard fire temperature regimes. The study focuses on analyzing the changes in thermal properties of steel and concrete at elevated temperatures, which significantly affect the load-bearing capacity of the structure. A numerical method based on the finite element approach was used to assess the fire resistance of concrete-filled steel tube (CFST) columns, accounting for the nonlinear behavior of materials over time and space. The research examines the influence of column geometry, cross-sectional shape, and thermal properties of the steel casing on the ultimate performance of the structural element. It was determined that the analyzed CFST column satisfies fire resistance class R 90.The research findings can be applied in the design of fire-resistant load-bearing elements for critical infrastructure facilities.Keywords:steel-concrete, fire resistance, testing, column, composite, temperature.

  • Open Access

    MATHEMATICAL MODELING OF THE BEHAVIOR OF THE PAN OF GLAZING IN CONDITIONS UNDER FIRE CONDITIONS

    by Valeriia Nekora, Serhii Pozdieiev, Ольга Некора, Svitlana Fedchenko, Vadym Nizhnyk, Taras Shnal, Сергій Поздєєв, Вадим Ніжник

    The article provides data on mathematical modeling of the behavior of a glass panel under the conditions of its one-sided heating according to the standard fire temperature regime. In the mathematical model of the glass panel under conditions of thermal influence, the process of heat transfer was reproduced based on the use of the non-stationary heat conduction equation. The stress-strain state of the glass panel was considered using the finite element method. The thermal effect was also combined with the mechanical stress due to the excess pressure that can occur in the room where the fire originates and develops. To study the propagation of cracks in glass, the strength criterion according to the Johnson-Holmquist model was applied. As a result of mathematical modeling, results that show the high efficiency and informativeness of the proposed approach were obtained. At the same time, data on the dynamics of the formation and propagation of cracks in the glass panel under conditions of heating according to the standard fire temperature regime were obtained. It is shown that the glass panel is destroyed due to the formation of a system of branched cracks, which is confirmed by empirical experience. As a result of conducting a numerical study of the behavior of the glass panel under heating conditions under the influence of the standard temperature regime of the fire, the onset of the limit state of loss of fire resistance based on integrity was obtained. It is shown that the fire resistance is lost if the glass panel is destroyed for 5 minutes under the influence of the standard fire temperature regime.

  • Open Access

    STUDY OF FIRE RESISTANCE OF REINFORCED CONCRETE BARS ACCORDING TO SPECIFIED CONCRETE STRENGTH INDICATORS

    by Svitlana Fedchenko, Serhii Pozdieiev, Ihor Fedchenko, Andrii Subota, State higher educational institution "Uzhhorod National University", Сергій Поздєєв, Ігор Федченко

    The article presents the results of determining the limit of fire resistance of reinforced concrete crossbars, taking into account the study of identification of strength characteristics of concrete based on the results of fire tests.During the fire tests, two serial reinforced concrete crossbars with the same structural parameters were investigated. The experimental setup made it possible to study full-size elements. The preparation, method of conducting and obtained results of fire tests are described in detail in the previous article. During the fire tests, temperature indicators were obtained at the control points of the cross-section of the tested elements and the value of their maximum deflection depending on the test time.The purpose of this article is based on determining the time of onset of the limit state as a sign of the loss of load-bearing capacity of reinforced concrete crossbars according to the specified concrete strength indicators, calculated based on the results of fire tests.Based on the obtained experimental temperature indicators, temperature interpolation was carried out and temperature distributions in the cross-sections of reinforced concrete crossbars were constructed. The obtained results are adequate, since the F criterion does not exceed the table values and is equal to 0.734. To clarify the strength properties of concrete, a deformation model was used, which is based on the use of equilibrium systems of internal layers in the section. The mathematical apparatus presented in the work allows rewriting the deformation model into a system of linear algebraic equations, the unknowns of which are the concrete strength reduction coefficients.Based on the value of the maximum deflection of the crossbars, the problem of strength was solved and the limit of fire resistance was determined according to the specified coefficients of concrete strength reduction. It is shown that the onset of the limit state due to the loss of bearing capacity is not reached in all cases and is determined according to the technical conditions (approximately 0.3 of the destructive load)М=50кНм.

  • STUDY OF STRENGTH REDUCTION OF REINFORCED CONCRETE BEAM UNDER FIRE TESTS

    by S. Fedchenko

    The article presents the results of studies of the regularity of changes in the concrete strength of reinforced concrete beams depending on the heating temperature of its inner layers under fire conditions by interpreting the temperature and deformation measurement results. To obtain the data necessary to identify patterns of concrete strength reduction, we developed a method of fire tests that substantiates the experimental base, design, and number of samples, type, number, and location of measuring devices, as well as the method for statistical processing of measurement data. Based on the developed methodology, we conducted fire tests. As a result of the tests, we obtained a set of measurement results in the form of time dependences of temperature indicators at individual cross-section points and the dependence of the maximum beam deflection on time, which are necessary to identify the coefficients of reduction in concrete strength of reinforced concrete beams under fire test conditions. We then used the proposed method to identify regularities in the reduction of concrete strength of a reinforced concrete beam, which includes interpolation using the obtained temperature indicators at individual points of the cross-section of the beam, which allows us to set the temperature at any point of the cross-section at any control time of measurements based on the approximation of isotherms by parabolas with a variable indicator of their degree. At the next stage, to identify the dependence of the concrete strength of reinforced concrete beams, we used a method based on the compilation of systems of equilibrium equations of internal layers in the cross-section of a reinforced concrete beam, in which the unknown values ​​are the coefficients of reduction of concrete strength for a range of temperatures every 100 °С in the range from 20 °С up to 1200 °С, provided that the reduction factor for the specified heating temperature of the inner layer of concrete is determined by linear interpolation. Using the proposed approach, we obtained appropriate results for a reinforced concrete beam subjected to fire tests. The obtained dependences of the strength reduction coefficient were used to evaluate the fire resistance of reinforced concrete beams and crossbars by the calculation method based on the deformation model. By comparing the obtained data with the data from the literature, we established the adequacy of the calculated data based on the relative deviation and Fisher’s test. The totality of the obtained data allows for improving the calculation method for evaluating reinforced concrete crossbars and beams by increasing the accuracy of the data obtained.


  • Open Access

    Method for identifying the strength characteristics of concrete of a reinforced concrete crossbar during heating under conditions of fire

    by Serhii Pozdieiev, Olga Nekora, Svitlana Fedchenko, Nataliya Zaika, Taras Shnal, Andriy Subota, Mykhailo Nesukh

    This paper proposes a method that makes it possible to study the patterns of changes in the concrete strength of reinforced concrete crossbars depending on the heating temperature under fire conditions by interpreting the results of their standard fire tests. For the implementation of this method, it is proposed to use similar data obtained using mathematical modeling based on the finite element method and given material properties, including the curve of concrete strength reduction recommended by the guidelines, as data included in the set of measurement results during fire tests depending on temperature. Such data are time dependences of temperature indicators at individual cross-section points and time dependence of the maximum deflection of the crossbar. The article proposes an interpolation method that makes it possible to set the temperature at any point of the section based on the approximation of the isotherms by parabolas with a variable indicator of their power. A method based on the mathematical interpretation of temperature indicators obtained using the proposed interpolation method and the curve of the dependence of the maximum deflection on time using a deformation model for describing the stress-strain state is proposed to identify the dependence of the concrete strength of reinforced concrete crossbars. The work also shows that the results obtained using the proposed method of identifying concrete strength reduction coefficients are adequate as their relative error is on average no more than 7 %. Based on the results, the possibility of its application to study the regularities of the decrease in the strength of reinforced concrete crossbars under fire conditions has been proven


  • Open Access

    JUSTIFICATION OF THE METHOD OF IDENTIFYING THE MECHANICAL CHARACTERISTICS OF CONCRETE OF REINFORCED CONCRETE BEAMS ACCORDING TO THE RESULTS OF FIRE TESTS

    by Cherkassy Institute of Fire Safety Named after Chernobyl Heroes ofNational University of Civil Defense of Ukraine, Svitlana Fedchenko

    Concrete is the most popular and widespread building material in the world. No construction of a private house or the construction of monolithic reinforced concrete structures is complete without concrete. The strength characteristics of concrete are slightly inferior to natural stone, and in some parameters even exceed it. The purpose of the work is to clarify the mechanical characteristics of concrete during its heating under conditions of exposure to the standard fire temperature regime. The proposed method of identifying the mechanical characteristics of concrete is based on the reproduction of the temperature distribution in the cross-sections of reinforced concrete beams based on the results of point temperature measurements during fire tests. In this method, the equations of equilibrium are used, compiled using the deformation mathematical model of the stress-strain state. Based on the obtained experimental data, the temperature distributions were reproduced using the proposed interpolation method. According to the obtained temperature distributions and the proposed mathematical apparatus, the coefficient of reduction in the concrete strength of reinforced concrete beams during fire tests was identified, the maximum deflection of two sample reinforced concrete beams was determined, and using a deformation model based on the use of equilibrium systems of internal layers in the cross section of reinforced concrete beams, the coefficient of reduction of strength of concrete under the condition of exposure to the standard fire temperature regime was specified. The presented curves of the value of the coefficient of reduction of concrete strength according to the proposed method and according to the recommendations of Eurocode 2 indicate the presence of a deviation between these indicators. The resulting refined dependence of the concrete strength reduction factor is the basis for improving the calculation method for assessing the fire resistance of reinforced concrete crossbars based on deformation models. Бетон – найпопулярніший і найпоширеніший будівельний матеріал у світі. Жодне будівництво чи то приватного будинку, чи то зведення монолітних залізобетонних конструкцій не обходиться без бетону. Міцнісні характеристики бетону мало поступаються природному каменю, а по деяким параметрам і зовсім перевищують його. Мета роботи полягає в уточненні механічних характеристик бетону під час його нагрівання за умов впливу стандартного температурного режиму пожежі. Запропонований метод ідентифікації механічних характеристик бетону ґрунтується на відтворенні розподілу температур у перерізах залізобетонних ригелів за результатами точкових вимірювань температури під час вогневих випробувань. В даному методі застосовуються рівняння рівноваги, складених з використанням деформаційної математичної моделі напружено-деформованого стану. За отриманими експериментальними даними, було виконано відтворення температурних розподілів з використанням запропонованого методу інтерполяції. За отриманими температурними розподілами та запропонованим математичним апаратом було ідентифіковано коефіцієнт зниження міцності бетону залізобетонних ригелів при проведенні вогневих випробувань, був визначений максимальний прогин двох залізобетонних ригелів-зразків та використовуючи деформаційну модель, що заснована на використанні систем рівноваги внутрішніх шарів у перерізі залізобетонних ригелів уточнено коефіцієнт зниження міцності бетону за умовою впливу стандартного температурного режиму пожежі. Представлені криві залежності значення коефіцієнта зниження міцності бетону за запропонованим методом та за рекомендаціями Eurocode 2 вказують на наявність відхилення між даними показниками. Отримана уточнена залежність коефіцієнта зниження міцності бетону є підґрунтям для удосконалення розрахункового методу оцінки вогнестійкості залізобетонних ригелів на основі деформаційних моделей.

  • Open Access

    Evaluation of fire resistance of reinforced concrete beams on the basis of use of parametric temperature curves of fire modes

    by Serhii Pozdieiev, Taras Shnal, Petro Kholod, Svitlana Fedchenko, Inna Nedilko

    The article considers the calculation method for assessing the fire resistance of reinforced concrete beams under the condition of parametric temperature regime of the fire. Temperature analysis for both parametric and standard fire exposure was performed and the corresponding plastic moments depending on the duration of the fire were determined. On the basis of the conducted research the diagrams of limiting moments for reinforced concrete beams are constructed. These diagrams allow you to check the strength conditions and assess the affiliation of reinforced concrete beams to the appropriate standard class of fire resistance. Using the constructed graphs of dependences of limiting plastic moments on the value of fire duration corresponding to standard classes of fire resistance for reinforced concrete beam, it is concluded that the standard temperature of fire is the most severe and leads to a constant reduction of limiting moment in contrast to others with horizontal branches, due to the descending branch of the calculated temperature of the fire according to the parameters of the room. On average, when using the temperature regimes of fire, determined by the proposed mathematical models, the limiting plastic moments are three times less than the limiting plastic moments determined under the influence of the standard temperature of the fire.