Péter Károly Juhász
Péter Károly Juhász has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
J. Jakabovic
Institute of Electronics and Photonics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Ilkovičova 3,812 19 Bratislava, Slovak Republic
1 shared publicationL. Harmatha
Institute of Electronics and Photonics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Ilkovičova 3,812 19 Bratislava, Slovak Republic
1 shared publication- Lubica Stuchlikova
Institute of Electronics and Photonics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology in Bratislava, Ilkovičova 3, 841 04 Bratislava, Slovakia
1 shared publication - Martin Weis
Institute of Electronics and Photonics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology in Bratislava, Ilkovičova 3, 841 04 Bratislava, Slovakia
1 shared publication - Michal Micjan
Institute of Electronics and Photonics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Ilkovičova 3,812 19 Bratislava, Slovak Republic
1 shared publication
Latest Publications
- Open Access
- 23 July 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 111
Improved evaluation of fiber reinforced concrete beam tests using an analytical model of fiber distribution and fracture cross-section location
- 23 July 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 111
Open AccessImproved evaluation of fiber reinforced concrete beam tests using an analytical model of fiber distribution and fracture cross-section location
- 1 June 2023
- Published by Springer Nature
- p. 757-767
Evaluation Method for Bending Beam Tests of Fibre Reinforced Concrete
- 1 June 2023
- Published by Springer Nature
- p. 757-767
Evaluation Method for Bending Beam Tests of Fibre Reinforced Concrete
- 9 July 2020
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 49 (5) , 3838-3858
A Proposed Evaluation Method for Three-Point Beam Tests of Fiber-Reinforced Concrete
The characteristic values of the material parameters used for structural design are usually determined from the mean and standard deviation of the material test results, and the design values are calculated from the characteristic values using the appropriate safety factor. However, if the standard deviation of the test data is high, the characteristic value is expected to be significantly lower than the mean value. In the case of fiber-reinforced concrete (FRC), the coefficient of variation is usually high, which can be attributed to the relatively small size of the specimen and the random location of the fibers. To overcome this limitation, this paper proposes a method that takes into account the number and location of the fibers when estimating the postcrack performance for a cracked cross section in a three-point notched bending beam tests. Test results of steel- and macrosynthetic FRC were evaluated using both the RILEM recommendations and the proposed method and are finally compared. Although the proposed method is more complex and the evaluation requires more effort than the existing method, it provides more repeatable material parameters, which exhibited a higher characteristic result.
- 9 July 2020
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 49 (5) , 3838-3858
A Proposed Evaluation Method for Three-Point Beam Tests of Fiber-Reinforced Concrete
The characteristic values of the material parameters used for structural design are usually determined from the mean and standard deviation of the material test results, and the design values are calculated from the characteristic values using the appropriate safety factor. However, if the standard deviation of the test data is high, the characteristic value is expected to be significantly lower than the mean value. In the case of fiber-reinforced concrete (FRC), the coefficient of variation is usually high, which can be attributed to the relatively small size of the specimen and the random location of the fibers. To overcome this limitation, this paper proposes a method that takes into account the number and location of the fibers when estimating the postcrack performance for a cracked cross section in a three-point notched bending beam tests. Test results of steel- and macrosynthetic FRC were evaluated using both the RILEM recommendations and the proposed method and are finally compared. Although the proposed method is more complex and the evaluation requires more effort than the existing method, it provides more repeatable material parameters, which exhibited a higher characteristic result.
- 1 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 529, 1-4
Determination of defect states in P3HT material for solar cell application
The defect states are investigated in ITO/P3HT/In organic diode structure by steady-state current-voltage technique and deep-level transient spectroscopy (DLTS) method. The temperature dependencies are used to evaluate charge transport activation energies. The activation energy of about 0.15 eV estimated from the current-voltage measurement as well as from the DLTS technique represents the dominant defect state in P3HT.
- 1 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 529, 1-4
Determination of defect states in P3HT material for solar cell application
The defect states are investigated in ITO/P3HT/In organic diode structure by steady-state current-voltage technique and deep-level transient spectroscopy (DLTS) method. The temperature dependencies are used to evaluate charge transport activation energies. The activation energy of about 0.15 eV estimated from the current-voltage measurement as well as from the DLTS technique represents the dominant defect state in P3HT.