TRThandiwe Bongani Radebe

Thandiwe Bongani Radebe

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Thandiwe Bongani Radebe has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Low-Cost Potassium Chloride Saltwater Phase Change Material System for a Household Refrigerator

    by Thandiwe Bongani Radebe, Asasei Unarine Casey Ndanduleni, Zhongjie Huan

    Thermal energy storage systems (TESS) are receiving attention because there are constant power cuts, major changes in electrical rate structures, increased maximum power demands, and incentive programmes sponsored by utilities. Household refrigerators were one of the main consumers of residential electricity, as they consume up to 26% and have an additional 17% greenhouse gas emissions. By incorporating TESS, this figure can be reduced. This study presents a low-cost potassium chloride saltwater phase change material (PCM) system to maintain a household refrigerator compartment below 5 ° C to preserve food and pharmaceutical products. After determining the 5-liter volume of PCM required, the experiments were carried out on a KIC KBF 525/1 ME refrigerator with an average daily power consumption of 0.567 kWh. With a heat transfer rate of 5 W and a total of 80 kJ of energy, the PCM took 2.5 days to fully solidify. It was then able to maintain the frigerated compartment at a temperature below 5 ° C for close to 25 hours, resulting in a 8W output power and a total of 90 kJ of energy being released. For power consumption analysis, 1.4175 kWh was used during the charging phase and 0.567 kWh was saved during the discharging phase. Heat transfer during the charging phase needs to be improved to better optimise the TESS.

  • Investigation of T-history Method Application for Sub-zero Phase Change Material Thermal Properties

    by Thandiwe Bongani Radebe, Asasei Unarine Casey Ndanduleni, Zhongjie Huan

    The T-history method, first proposed by Zhang & Jiang, is a simple method used to determine the latent heat, specific heat, thermal conductivity, melting point, and degree of supercooling of a phase-change material (PCM). The method is based on the measurement of the temperature of the material over time. It assumes that the PCM sample and the reference material exchange thermal energy with the environment in a similar manner, because it is based on the lumped capacitance method, and the temperature distribution inside the sample is uniform. There are multiple advantages that the T history method has over conventional methods; however, the T history method also has some downfalls, which have been improved over the years by different authors. This study experimentally investigates the reliability of this technique for PCM with a phase change temperature below 0 ° C. The technique is used to first determine the properties of denoised water with a phase change temperature of 0 ° C, using ethylene glycol with a mixture ratio of 50/50 as reference material. Second, by determining the properties of KCl with a concentration of 19.5% salt to water for a phase change temperature of -10 ° C. Two analytical approaches were used, one by immersing the samples in antifreeze during the charging process and the other by exposing the samples to ambient air during the discharging phase. The experimental results were further validated using the known literature to determine the latent heat of KCl. This study found that the latent heat of KCl measured using the technique has a 6.2% difference from the known results determined by the DSC. This study recommends the use of the T history method when designing latent heat thermal energy storage systems (LHTESS), because the sample size is an important characteristic for accurate thermophysical properties during the design process.


  • Open Access

    The impact of technology adoption in teaching and learning within ODeL

    by Thandiwe Bongani Radebe, Ronny Tebeta, Rendani Wilson Maladzhi

    The emergence of the fourth industrial revolution (4IR) instigated various institutions of the world to move towards technology integration in teaching and learning. The purpose of the current study was to assess how impactful was Wolfram System Modeler (WSM) software to students in their studies by utilising the technology acceptance model. MS forms online survey was utilised to collect data from participating students of the Solid Mechanics (SME3701) module. SME3701 module was targeted whereby 95 students participated. Data analysis was done through IBM SPSS Statistics. The findings of the study indicated that students found the software WSM interesting as evidence of the module performance as compared to before the introduction of the technology. The module performance improved drastically as evidence of the students ‘acceptability of the technology.