Amalie Solberg
Amalie Solberg has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Ali Harlin
VTT Technical Research Centre of Finland
1 shared publication - Alistair William Thomas King
VTT Technical Research Centre of Finland Ltd., Tietorie 4e, 02150 Espoo, Finland
1 shared publication - Anders Ståhlberg
Department of Laboratory Medicine, Sahlgrenska Center for Cancer Research, Institute of Biomedicine, Sahlgrenska Academy, University of Gothenburg, Gothenburg, Sweden
1 shared publication - Anniina Savolainen
VTT Technical Research Centre of Finland
1 shared publication - Antti Korpela
VTT – Technical Research Centre of Finland
1 shared publication - Antti Paajanen
VTT Technical Research Centre of Finland Ltd
1 shared publication
Latest Publications
- Open Access
- 20 February 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Controlled surface acetylation of cellulosics to tune biodegradability while expanding their use towards common petrochemical-based plastics
The European Commissions single-use plastics directive has put major restrictions on the use of chemically modified cellulosics for different material applications, e.g., as films, fibres, foams and other shaped objects. In addition, the wet strength and barrier properties of some of these materials are lacking, in comparison to petrochemical-based plastics. In the current study we demonstrate that it is possible to carry out surface selective acetylation of kraft fibre paper and nano-paper to create materials that maintain biodegradability. This is shown to be highly dependent on the degree of bulk acetylation, with those materials with modification restricted to fibril surface monoacetylation offering fine control over enzymatic digestibility. Materials which show the formation of cellulose triacetate were much less degradable in the timeframe of our assessment methods. However, the wet strength and extensibility of these materials was significantly improved, pushing the envelope for application towards moisture-rich environments. The mechanistic component of our study shows acetylation occurs down to the fibril surface level, and not just on the macrofibre level. We believe that this study offers a strong basis for widening the application scope of cellulosics towards traditionally petrochemical-based plastics
- 20 February 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessControlled surface acetylation of cellulosics to tune biodegradability while expanding their use towards common petrochemical-based plastics
The European Commissions single-use plastics directive has put major restrictions on the use of chemically modified cellulosics for different material applications, e.g., as films, fibres, foams and other shaped objects. In addition, the wet strength and barrier properties of some of these materials are lacking, in comparison to petrochemical-based plastics. In the current study we demonstrate that it is possible to carry out surface selective acetylation of kraft fibre paper and nano-paper to create materials that maintain biodegradability. This is shown to be highly dependent on the degree of bulk acetylation, with those materials with modification restricted to fibril surface monoacetylation offering fine control over enzymatic digestibility. Materials which show the formation of cellulose triacetate were much less degradable in the timeframe of our assessment methods. However, the wet strength and extensibility of these materials was significantly improved, pushing the envelope for application towards moisture-rich environments. The mechanistic component of our study shows acetylation occurs down to the fibril surface level, and not just on the macrofibre level. We believe that this study offers a strong basis for widening the application scope of cellulosics towards traditionally petrochemical-based plastics
- Open Access
- 3 June 2023
- Published by MDPI AG in Bioengineering
- Vol. 10 (6) , 682
Polysaccharides and Structural Proteins as Components in Three-Dimensional Scaffolds for Breast Cancer Tissue Models: A Review
Breast cancer is the most common cancer among women, and even though treatments are available, efficiency varies with the patients. In vitro 2D models are commonly used to develop new treatments. However, 2D models overestimate drug efficiency, which increases the failure rate in later phase III clinical trials. New model systems that allow extensive and efficient drug screening are thus required. Three-dimensional printed hydrogels containing active components for cancer cell growth are interesting candidates for the preparation of next generation cancer cell models. Macromolecules, obtained from marine- and land-based resources, can form biopolymers (polysaccharides such as alginate, chitosan, hyaluronic acid, and cellulose) and bioactive components (structural proteins such as collagen, gelatin, and silk fibroin) in hydrogels with adequate physical properties in terms of porosity, rheology, and mechanical strength. Hence, in this study attention is given to biofabrication methods and to the modification with biological macromolecules to become bioactive and, thus, optimize 3D printed structures that better mimic the cancer cell microenvironment. Ink formulations combining polysaccharides for tuning the mechanical properties and bioactive polymers for controlling cell adhesion is key to optimizing the growth of the cancer cells.
- 3 June 2023
- Published by MDPI AG in Bioengineering
- Vol. 10 (6) , 682
Open AccessPolysaccharides and Structural Proteins as Components in Three-Dimensional Scaffolds for Breast Cancer Tissue Models: A Review
Breast cancer is the most common cancer among women, and even though treatments are available, efficiency varies with the patients. In vitro 2D models are commonly used to develop new treatments. However, 2D models overestimate drug efficiency, which increases the failure rate in later phase III clinical trials. New model systems that allow extensive and efficient drug screening are thus required. Three-dimensional printed hydrogels containing active components for cancer cell growth are interesting candidates for the preparation of next generation cancer cell models. Macromolecules, obtained from marine- and land-based resources, can form biopolymers (polysaccharides such as alginate, chitosan, hyaluronic acid, and cellulose) and bioactive components (structural proteins such as collagen, gelatin, and silk fibroin) in hydrogels with adequate physical properties in terms of porosity, rheology, and mechanical strength. Hence, in this study attention is given to biofabrication methods and to the modification with biological macromolecules to become bioactive and, thus, optimize 3D printed structures that better mimic the cancer cell microenvironment. Ink formulations combining polysaccharides for tuning the mechanical properties and bioactive polymers for controlling cell adhesion is key to optimizing the growth of the cancer cells.