Sema Nur Belen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sema Nur Belen has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Ugur Cengiz
Canakkale Onsekiz Mart University, Faculty of Engineering, Department of Chemical Engineering, Çanakkale, Turkey
2 shared publications Candan Cengiz
AFC Green Technologies R&D, Çanakkale Technopark, Sarıcaeli
1 shared publication- Duygu Çetin
Department of Chemistry and Chemical Processing Technologies, Hereke Asim Kocabiyik Vocational School, Kocaeli University, Kocaeli, Turkey
1 shared publication Mehtap Cantürk Bamyacı
Department of Polymer Science and Technology
1 shared publication- Olcay Mert
Department of Chemistry, Kocaeli University, 41001 Kocaeli, Türkiye
1 shared publication - Ozgur Ozay
Laboratory of Biomaterials Research, Department of Bioengineering, Faculty of Engineering, Çanakkale Onsekiz Mart University
1 shared publication
Latest Publications
- Open Access
Hydrogels Activated with Plant Extracts/Bioactive Compounds for Cancer Treatment: From Design to Application
Plant extracts and plant-derived bioactive compounds are considered important natural agents in cancer research due to their antiproliferative, pro-apoptotic, antioxidant, anti-inflammatory, and anti-angiogenic effects. However, the low solubility, limited bioavailability, instability, and challenges in their standardization directly limit their therapeutic use. Therefore, the development of new delivery systems has become necessary. In this context, hydrogels are among the biomaterial platforms gaining attention in cancer treatment. This review provides a comprehensive assessment of the potential of hydrogel systems containing plant extracts and plant-derived bioactive compounds in cancer treatment. The article discusses cancer types, the limitations of current treatments, mechanisms of action of plant-derived bioactive compounds against cancer, stimulus-responsive hydrogel systems, and the design criteria for extract-loaded hydrogels. In addition, hydrogel systems containing plant-derived components and combination approaches that use these components alongside anticancer drugs have been investigated. According to the literature, these compounds may increase anticancer activity through local, prolonged release, reduce the toxicity of chemotherapeutic agents in some cases, and exhibit complementary or synergistic antitumor effects with chemotherapeutic drugs. They also point out the potential of treatment strategies targeting the tumor microenvironment. However, researchers need to conduct more comprehensive studies on extraction standardization, biosafety, release kinetics, in vivo efficacy, and clinical scalability. In conclusion, hydrogel systems containing plant extracts and plant-derived bioactive compounds should be considered not as direct alternatives to cancer treatments but as rational biomaterial platforms that enable controlled release, local application, and combination therapies.
Open AccessHydrogels Activated with Plant Extracts/Bioactive Compounds for Cancer Treatment: From Design to Application
Plant extracts and plant-derived bioactive compounds are considered important natural agents in cancer research due to their antiproliferative, pro-apoptotic, antioxidant, anti-inflammatory, and anti-angiogenic effects. However, the low solubility, limited bioavailability, instability, and challenges in their standardization directly limit their therapeutic use. Therefore, the development of new delivery systems has become necessary. In this context, hydrogels are among the biomaterial platforms gaining attention in cancer treatment. This review provides a comprehensive assessment of the potential of hydrogel systems containing plant extracts and plant-derived bioactive compounds in cancer treatment. The article discusses cancer types, the limitations of current treatments, mechanisms of action of plant-derived bioactive compounds against cancer, stimulus-responsive hydrogel systems, and the design criteria for extract-loaded hydrogels. In addition, hydrogel systems containing plant-derived components and combination approaches that use these components alongside anticancer drugs have been investigated. According to the literature, these compounds may increase anticancer activity through local, prolonged release, reduce the toxicity of chemotherapeutic agents in some cases, and exhibit complementary or synergistic antitumor effects with chemotherapeutic drugs. They also point out the potential of treatment strategies targeting the tumor microenvironment. However, researchers need to conduct more comprehensive studies on extraction standardization, biosafety, release kinetics, in vivo efficacy, and clinical scalability. In conclusion, hydrogel systems containing plant extracts and plant-derived bioactive compounds should be considered not as direct alternatives to cancer treatments but as rational biomaterial platforms that enable controlled release, local application, and combination therapies.
- Open Access
- 20 February 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (8) , 8499-8511
Synthesis, Hydrolytic Degradation Behavior, and Surface Properties of Poly(alkyl glycolide)-Polyglycolide Copolymers
Given the environmental impact of polymers on our daily lives, the development of biodegradable polymers is becoming increasingly critical. Poly(diisobutyl glycolide)-polyglycolide (PDIBG-PGA) and poly(diisopropyl glycolide)-polyglycolide (PDIPG-PGA) copolymers, which are structurally similar to polylactic-co-glycolic acid (PLGA) polyesters frequently used in the field of biomaterials, were synthesized via ring-opening polymerization (ROP) of glycolide with l-diisobutyl glycolide (l-DIBG) or l-diisopropyl glycolide (l-DIPG), respectively, in various molecular weights (M w GPC: 15.5-40.0 kDa) and in high yields (up to 85.0%). The wettability characteristics of biodegradable polymers are important not only in air but also for their behavior in underwater environments. PDIBG-PGA silica composites, due to their amphiphilic nature, exhibited water contact angles between 72° and 85° in air, unaffected by the increasing addition of hydrophilic silica nanoparticles. However, underwater-oil contact angles increased from 75° to 165° as a result of the higher silica nanoparticle content and enhanced surface roughness. When the silica content reached 30%, the surface demonstrated self-cleaning and oil-repellent properties underwater, attributed to the Cassie state, which trapped air within the surface's hierarchical roughness. Furthermore, the surface free energy (SFE) values of PDIBG-PGA and PDIPG-PGA copolymer films were evaluated using the Owens-Wendt method, which revealed an increasing underwater hexadecane contact angle as the polar component interactions increased. Differential scanning calorimetry analysis revealed that all synthesized copolymers were amorphous, and the glass transition temperatures (T g) increased with the increase in the molecular weight of the copolymers (for instance, M n GPC: 9560 g/mol → T g: 25.1 °C vs M n GPC: 20,850 g/mol → T g: 32.3 °C for PDIBG-PGA; M n GPC: 10,670 g/mol → T g: 37.7 °C vs M n GPC: 23,360 g/mol → T g: 42.3 °C for PDIPG-PGA). The molecular weight decreases of 88.3% and 76.5% and mass losses of 36.7% and 12.3% were observed for PDIBG-PGA and PDIPG-PGA copolymers after 8 weeks of hydrolytic degradation, respectively. The faster degradation of PDIBG-PGA (T g: 25.1 °C) than PDIPG-PGA (T g: 37.7 °C) may be attributed to the T g below the hydrolytic degradation temperature (37 °C) because of an increase in the mobility of PDIBG-PGA polymer chains, allowing water molecules to transfer more easily through the matrix.
- 20 February 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (8) , 8499-8511
Open AccessSynthesis, Hydrolytic Degradation Behavior, and Surface Properties of Poly(alkyl glycolide)-Polyglycolide Copolymers
Given the environmental impact of polymers on our daily lives, the development of biodegradable polymers is becoming increasingly critical. Poly(diisobutyl glycolide)-polyglycolide (PDIBG-PGA) and poly(diisopropyl glycolide)-polyglycolide (PDIPG-PGA) copolymers, which are structurally similar to polylactic-co-glycolic acid (PLGA) polyesters frequently used in the field of biomaterials, were synthesized via ring-opening polymerization (ROP) of glycolide with l-diisobutyl glycolide (l-DIBG) or l-diisopropyl glycolide (l-DIPG), respectively, in various molecular weights (M w GPC: 15.5-40.0 kDa) and in high yields (up to 85.0%). The wettability characteristics of biodegradable polymers are important not only in air but also for their behavior in underwater environments. PDIBG-PGA silica composites, due to their amphiphilic nature, exhibited water contact angles between 72° and 85° in air, unaffected by the increasing addition of hydrophilic silica nanoparticles. However, underwater-oil contact angles increased from 75° to 165° as a result of the higher silica nanoparticle content and enhanced surface roughness. When the silica content reached 30%, the surface demonstrated self-cleaning and oil-repellent properties underwater, attributed to the Cassie state, which trapped air within the surface's hierarchical roughness. Furthermore, the surface free energy (SFE) values of PDIBG-PGA and PDIPG-PGA copolymer films were evaluated using the Owens-Wendt method, which revealed an increasing underwater hexadecane contact angle as the polar component interactions increased. Differential scanning calorimetry analysis revealed that all synthesized copolymers were amorphous, and the glass transition temperatures (T g) increased with the increase in the molecular weight of the copolymers (for instance, M n GPC: 9560 g/mol → T g: 25.1 °C vs M n GPC: 20,850 g/mol → T g: 32.3 °C for PDIBG-PGA; M n GPC: 10,670 g/mol → T g: 37.7 °C vs M n GPC: 23,360 g/mol → T g: 42.3 °C for PDIPG-PGA). The molecular weight decreases of 88.3% and 76.5% and mass losses of 36.7% and 12.3% were observed for PDIBG-PGA and PDIPG-PGA copolymers after 8 weeks of hydrolytic degradation, respectively. The faster degradation of PDIBG-PGA (T g: 25.1 °C) than PDIPG-PGA (T g: 37.7 °C) may be attributed to the T g below the hydrolytic degradation temperature (37 °C) because of an increase in the mobility of PDIBG-PGA polymer chains, allowing water molecules to transfer more easily through the matrix.
- 6 March 2023
- Published by Canakkale Onsekiz Mart University in Journal of Advanced Research in Natural and Applied Sciences
- Vol. 9 (1) , 158-166
Fabrication of Self-Cleaning Perfluoroacrylate Blend Films by Spray Coating Method
The superhydrophobic surfaces are contained two essential principles. First, low surface energy polymers, such as fluoropolymers pushing the liquid onto the surface are necessary. The surface roughness is the second necessity to obtain superhydrophobicity, providing air packets between the roughness and reducing surface interaction with the liquid. This study fabricated the superhydrophobic blend coating using a spray coating method. The flat surface of PFMA homopolymer synthesized in scCO2 medium was fabricated free meniscus coating method due to the lack of solubility in the conventional solvent. To overcome the solubility problems of the PFMA, the p(Perfluoromethacrylate-ran-Styrene) copolymer was fabricated in a scCO2 medium. Blend solutions are prepared to reduce costs and provide high hydrophobicity by using p(Perfluoromethacrylate-ran-Styrene) copolymer and PS homopolymers. The surface roughness of the blend films was altered using silica nanoparticles coated on a glass slide by a spray coating. The surface morphology was characterized by SEM analyses indicating that double-scale surface morphology was obtained by increasing the SNp of the composite solution. The water contact angle indicated that the superhydrophobic rough surface was obtained with TMS70 and PS blend formation having 33.0 % PS and 12.5% silica nanoparticles.
- 6 March 2023
- Published by Canakkale Onsekiz Mart University in Journal of Advanced Research in Natural and Applied Sciences
- Vol. 9 (1) , 158-166
Fabrication of Self-Cleaning Perfluoroacrylate Blend Films by Spray Coating Method
The superhydrophobic surfaces are contained two essential principles. First, low surface energy polymers, such as fluoropolymers pushing the liquid onto the surface are necessary. The surface roughness is the second necessity to obtain superhydrophobicity, providing air packets between the roughness and reducing surface interaction with the liquid. This study fabricated the superhydrophobic blend coating using a spray coating method. The flat surface of PFMA homopolymer synthesized in scCO2 medium was fabricated free meniscus coating method due to the lack of solubility in the conventional solvent. To overcome the solubility problems of the PFMA, the p(Perfluoromethacrylate-ran-Styrene) copolymer was fabricated in a scCO2 medium. Blend solutions are prepared to reduce costs and provide high hydrophobicity by using p(Perfluoromethacrylate-ran-Styrene) copolymer and PS homopolymers. The surface roughness of the blend films was altered using silica nanoparticles coated on a glass slide by a spray coating. The surface morphology was characterized by SEM analyses indicating that double-scale surface morphology was obtained by increasing the SNp of the composite solution. The water contact angle indicated that the superhydrophobic rough surface was obtained with TMS70 and PS blend formation having 33.0 % PS and 12.5% silica nanoparticles.