Leonardo Marchiori
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Leonardo Marchiori has a total of 145 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Albuquerque
GeoBioTec, Department of Civil Engineering and Architecture, University of Beira Interior, 6201-001 Covilhã, Portugal
17 shared publications - Maria Vitoria Morais
GeoBioTec, Civil Engineering Department, University of Beira Interior, 6201-001 Covilhã, Portugal
15 shared publications - Victor Cavaleiro
GeoBioTec, Department of Civil Engineering, University of Beira Interior, 6201-001 Covilhã, Portugal
12 shared publications - Luis Andrade Pais
GeoBioTec, Department of Civil Engineering, University of Beira Interior, 6201-001 Covilhã, Portugal
10 shared publications Victor Cavaleiro
9 shared publications- André Studart
GeoBioTec, Civil Engineering and Architecture Department, Faculty of Engineering, University of Beira Interior, Travessa Fonte do Lameiro6, 6200-358 Covilhã, Portugal
7 shared publications
Latest Publications
- Open Access
- 1 November 2026
- Published by Elsevier in Process Safety and Environmental Protection
- Vol. 222
Valorization of industrial wastes as alternative liner materials: Compressibility and shear strength
- 1 November 2026
- Published by Elsevier in Process Safety and Environmental Protection
- Vol. 222
Open AccessValorization of industrial wastes as alternative liner materials: Compressibility and shear strength
- Open Access
- 1 October 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Journal of Ecological Engineering
- Vol. 27 (10) , 279-287
Soil physicochemical properties and implications for leachate mobility in an Amazonian open dumpsite
Open dumps remain the predominant form of municipal solid waste disposal in many Amazonian municipalities, posing significant risks to soil and water resources due to uncontrolled leachate generation. This study evaluates soil physicochemical properties in an active open dumpsite located in...
- 1 October 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Journal of Ecological Engineering
- Vol. 27 (10) , 279-287
Open AccessSoil physicochemical properties and implications for leachate mobility in an Amazonian open dumpsite
Open dumps remain the predominant form of municipal solid waste disposal in many Amazonian municipalities, posing significant risks to soil and water resources due to uncontrolled leachate generation. This study evaluates soil physicochemical properties in an active open dumpsite located in...
- Open Access
- 2 July 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (7) , 264
An Exploratory GIS-Based Contribution to Geothermal Favourability Mapping in Hercynian Granite-Hosted Fractured Systems: Guarda District, Central Portugal
Geothermal energy is a locally available, low-carbon resource that may support heat supply, building decarbonisation and regional energy diversification in non-volcanic crystalline settings. This study proposes an exploratory GIS-based approach for geothermal favourability mapping in the Guarda District, Central Portugal, where Hercynian granites, major fault systems and thermal and mineral water occurrences define a structurally controlled hydrogeothermal framework. Hydrogeochemical data from 54 groundwater abstraction points were integrated through silica-derived apparent geothermometric indicators, classical hydrothermal-parameter estimation and Empirical Bayesian Kriging Regression Prediction (EBKRP). Apparent silica-derived temperature indicators, circulation depth, geothermal gradient and theoretical thermal power were estimated, with log10 transformed thermal power used as the dependent variable and distance to major mapped faults as the structural covariate. Apparent silica-derived temperature indicators range from 21.3 °C to 121.2 °C, with a mean of 64.6 °C, while estimated geothermal gradients range from 20.3 °C/km to 92.1 °C/km. Higher estimated values occur preferentially near NE–SW and NNW–SSE fault systems, suggesting that structural permeability may influence deep groundwater circulation. The interpretation explicitly acknowledges that, in low-temperature systems, dissolved silica may be influenced by chalcedony or amorphous silica control, as well as by cooling, mixing and incomplete re-equilibration during fluid ascent. The resulting map is interpreted as a screening-level favourability product, not as a definitive assessment of exploitable geothermal resources, and supports the prioritisation of future structural mapping, geophysical surveys, exploratory drilling, borehole temperature logging and applied geothermal assessment in fractured granitic terrains.
- 2 July 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (7) , 264
Open AccessAn Exploratory GIS-Based Contribution to Geothermal Favourability Mapping in Hercynian Granite-Hosted Fractured Systems: Guarda District, Central Portugal
Geothermal energy is a locally available, low-carbon resource that may support heat supply, building decarbonisation and regional energy diversification in non-volcanic crystalline settings. This study proposes an exploratory GIS-based approach for geothermal favourability mapping in the Guarda District, Central Portugal, where Hercynian granites, major fault systems and thermal and mineral water occurrences define a structurally controlled hydrogeothermal framework. Hydrogeochemical data from 54 groundwater abstraction points were integrated through silica-derived apparent geothermometric indicators, classical hydrothermal-parameter estimation and Empirical Bayesian Kriging Regression Prediction (EBKRP). Apparent silica-derived temperature indicators, circulation depth, geothermal gradient and theoretical thermal power were estimated, with log10 transformed thermal power used as the dependent variable and distance to major mapped faults as the structural covariate. Apparent silica-derived temperature indicators range from 21.3 °C to 121.2 °C, with a mean of 64.6 °C, while estimated geothermal gradients range from 20.3 °C/km to 92.1 °C/km. Higher estimated values occur preferentially near NE–SW and NNW–SSE fault systems, suggesting that structural permeability may influence deep groundwater circulation. The interpretation explicitly acknowledges that, in low-temperature systems, dissolved silica may be influenced by chalcedony or amorphous silica control, as well as by cooling, mixing and incomplete re-equilibration during fluid ascent. The resulting map is interpreted as a screening-level favourability product, not as a definitive assessment of exploitable geothermal resources, and supports the prioritisation of future structural mapping, geophysical surveys, exploratory drilling, borehole temperature logging and applied geothermal assessment in fractured granitic terrains.
- 1 May 2026
- Published by Springer Nature
- p. 227-236
Chemical Characterization of Industrial By-Products: Sustainable Liners for Waste Containment Systems
- 1 May 2026
- Published by Springer Nature
- p. 227-236
Chemical Characterization of Industrial By-Products: Sustainable Liners for Waste Containment Systems
- Open Access
- 23 March 2026
- Published by MDPI AG in Smart Cities
- Vol. 9 (3) , 54
GeoBIM for Geothermal Energy Efficiency in Buildings and Smart Cities: A Review
The global drive toward energy transition and carbon neutrality requires integrated and data-driven approaches for managing buildings and smart cities. Existing urban energy assessment frameworks remain fragmented and often lack multiscale interoperability between building-level models and territorial datasets. At the same time, shallow geothermal energy is emerging as an efficient and renewable solution for sustainable heating and cooling. To address these gaps, this study examines the potential of GeoBIM, the integration of Building Information Modeling (BIM) and Geographic Information Systems (GIS), as a unified framework for multiscale energy analysis and for supporting shallow geothermal applications. A systematic literature review was conducted based on the PRISMA framework, combining a systematic literature review using the Scopus database with the critical examination of representative case studies. The results show that GeoBIM-based modeling improves data quality, enhances thermal performance assessments, and supports the implementation of shallow geothermal systems, including energy piles and district-scale ground-coupled networks. Reported applications demonstrate energy consumption reductions exceeding 40% in certain urban contexts. Several research gaps and challenges were identified, particularly data interoperability issues, lack of standardization, computational complexity, and the need for specialized training. Overall, the review indicates that GeoBIM offers a promising pathway for optimizing resources, supporting informed decision-making, and advancing resilient and sustainable smart buildings and cities.
- 23 March 2026
- Published by MDPI AG in Smart Cities
- Vol. 9 (3) , 54
Open AccessGeoBIM for Geothermal Energy Efficiency in Buildings and Smart Cities: A Review
The global drive toward energy transition and carbon neutrality requires integrated and data-driven approaches for managing buildings and smart cities. Existing urban energy assessment frameworks remain fragmented and often lack multiscale interoperability between building-level models and territorial datasets. At the same time, shallow geothermal energy is emerging as an efficient and renewable solution for sustainable heating and cooling. To address these gaps, this study examines the potential of GeoBIM, the integration of Building Information Modeling (BIM) and Geographic Information Systems (GIS), as a unified framework for multiscale energy analysis and for supporting shallow geothermal applications. A systematic literature review was conducted based on the PRISMA framework, combining a systematic literature review using the Scopus database with the critical examination of representative case studies. The results show that GeoBIM-based modeling improves data quality, enhances thermal performance assessments, and supports the implementation of shallow geothermal systems, including energy piles and district-scale ground-coupled networks. Reported applications demonstrate energy consumption reductions exceeding 40% in certain urban contexts. Several research gaps and challenges were identified, particularly data interoperability issues, lack of standardization, computational complexity, and the need for specialized training. Overall, the review indicates that GeoBIM offers a promising pathway for optimizing resources, supporting informed decision-making, and advancing resilient and sustainable smart buildings and cities.
- Open Access
- 20 February 2026
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 28 (3) , 1897-1915
Valorization of industrial wastes as alternative liner materials: toxicity assessment
The use of alternative materials for engineering barriers based on industrial waste has gained attention due to disposal concerns and excessive consumption of natural resource consumption. However, waste-based toxicity regarding leaching behavior must be assessed prior to reutilization. This study investigates the feasibility of using water treatment sludge (WTS), vegetal biomass ash (VBA), granitic mining waste (GMW), and blast furnace slag (BFS), mixed in different ratios with a natural soil as alternative materials for liners. The assessment was carried out following microstructure and chemical through energy dispersive spectrometry attached to scanning electron microscopy (SEM-EDS), mineralogy from X-ray Diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and toxicity characteristic leaching procedure (TCPL). Results revealed pH values ranging from 5.55 for WTS to 11.1 for BFS, influenced their interactions in liners, specifically, GMW closely resembles local bedrock and poses minimal contamination risk; BFS, rich in iron and calcium oxides, shows potential cementitious properties but requires assessment for expansive behavior; VBA, transformed through incineration, exhibits pozzolanic potential due to high Si, Al, and Fe content; and WTS, mainly amorphous, reduces mixture density but requires further pozzolanic activity analysis. Regarding chemical stability and leaching potential, WTS’ alumina and silica potentially adsorb, bind and mobilize certain metals, GMW’s quartz and feldspar results in low metal mobility, and VBA and BFS alkalinity can encapsulate pollutants via hydration products. Across all materials, TCLP results were below regulatory limits. This research highlights the dual benefits of reducing industrial waste disposal and developing sustainable geomaterials for geotechnical applications.
- 20 February 2026
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 28 (3) , 1897-1915
Open AccessValorization of industrial wastes as alternative liner materials: toxicity assessment
The use of alternative materials for engineering barriers based on industrial waste has gained attention due to disposal concerns and excessive consumption of natural resource consumption. However, waste-based toxicity regarding leaching behavior must be assessed prior to reutilization. This study investigates the feasibility of using water treatment sludge (WTS), vegetal biomass ash (VBA), granitic mining waste (GMW), and blast furnace slag (BFS), mixed in different ratios with a natural soil as alternative materials for liners. The assessment was carried out following microstructure and chemical through energy dispersive spectrometry attached to scanning electron microscopy (SEM-EDS), mineralogy from X-ray Diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and toxicity characteristic leaching procedure (TCPL). Results revealed pH values ranging from 5.55 for WTS to 11.1 for BFS, influenced their interactions in liners, specifically, GMW closely resembles local bedrock and poses minimal contamination risk; BFS, rich in iron and calcium oxides, shows potential cementitious properties but requires assessment for expansive behavior; VBA, transformed through incineration, exhibits pozzolanic potential due to high Si, Al, and Fe content; and WTS, mainly amorphous, reduces mixture density but requires further pozzolanic activity analysis. Regarding chemical stability and leaching potential, WTS’ alumina and silica potentially adsorb, bind and mobilize certain metals, GMW’s quartz and feldspar results in low metal mobility, and VBA and BFS alkalinity can encapsulate pollutants via hydration products. Across all materials, TCLP results were below regulatory limits. This research highlights the dual benefits of reducing industrial waste disposal and developing sustainable geomaterials for geotechnical applications.
- Open Access
- 21 December 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 49 (3)
Geomechanical and structural analysis of contaminated residual granitic soils with gasoline
Human activity brings several risks of contamination with pollutants of varying types and effects, with hydrocarbon compounds being of great concern as they are released by vehicles, industrial and construction activities and in areas with fuel reservoirs, among others. Hence, when these contaminants reach the soil, a legitimate question arises regarding their impact on the soil’s resistance characteristics. This work presents a case study of granite residual soils contaminated with gasoline under 8-, 16-, and 32-days, within index properties and geomechanical tests were analyzed to support remediation decision. CBR tests showed inconsistent results at shallow depths but a 16% capacity reduction beyond 12 mm with green gasoline. Direct shear tests showed similar friction angles but increased cohesion from particle aggregation, raising rupture stress by up to 68%. Oedometer tests showed greater deformability and lower yield stress, with compressibility coefficient around 0.133- 0.161, in contaminated soils, aligning with large-deformation CBR trends. It seems that gasoline is a complex addition to the soil-water-air interaction, possibly transforming the soil into a hydro-phobic material and thus separating the water as the connecting agent, affecting the overall structure and support capacity of the soil. Future studies should focus on hydrocarbon percolation and leaching behavior in field conditions.
- 21 December 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 49 (3)
Open AccessGeomechanical and structural analysis of contaminated residual granitic soils with gasoline
Human activity brings several risks of contamination with pollutants of varying types and effects, with hydrocarbon compounds being of great concern as they are released by vehicles, industrial and construction activities and in areas with fuel reservoirs, among others. Hence, when these contaminants reach the soil, a legitimate question arises regarding their impact on the soil’s resistance characteristics. This work presents a case study of granite residual soils contaminated with gasoline under 8-, 16-, and 32-days, within index properties and geomechanical tests were analyzed to support remediation decision. CBR tests showed inconsistent results at shallow depths but a 16% capacity reduction beyond 12 mm with green gasoline. Direct shear tests showed similar friction angles but increased cohesion from particle aggregation, raising rupture stress by up to 68%. Oedometer tests showed greater deformability and lower yield stress, with compressibility coefficient around 0.133- 0.161, in contaminated soils, aligning with large-deformation CBR trends. It seems that gasoline is a complex addition to the soil-water-air interaction, possibly transforming the soil into a hydro-phobic material and thus separating the water as the connecting agent, affecting the overall structure and support capacity of the soil. Future studies should focus on hydrocarbon percolation and leaching behavior in field conditions.
- Open Access
- 5 November 2025
- Published by Polish Mineral Engineering Society in Inżynieria Mineralna
- Vol. 2 (2)
Integrated Characterization Using SCPTu, CPTu, and Dynamic Penetration Tests for Geotechnical Sustainability
The present study focuses on the geotechnical characterization of a rock mass in Covilhã (Portugal) using in situ testing techniques. The research aims to enhance the understanding of subsurface conditions by integrating multiple geotechnical investigation methods, including the seismic piezocone penetration test with pore pressure measurements (SCPTu), without seismic (CPTu), dynamic penetration tests (DPM and DPSH). These tests provide critical data on soil mechanical resistance, internal structure, and deformation properties, supporting more accurate foundation and infrastructure design decisions. The results indicate that the studied soil primarily consists of sand to silty sand with high and increasing over consolidated ratio and relative density, showing a trend towards cementation. The SCPTu test proved highly effective in assessing initial stiffness and computing deformation moduli, significantly contributing to geotechnical engineering applications. Additionally, DPM and DPSH have provided complementary data, allowing for a more comprehensive evaluation of subsurface variability. The integration of these methods enhanced the reliability of soil classification, ensuring robust datasets for geotechnical analysis and infrastructure development. This research aligns with the themes of in - situ testing for geotechnical development. The findings emphasize the importance of multidisciplinary approaches in advancing infrastructure resilience and sustainability through accurate subsurface characterization. The combination of SCPTu, CPTu, and dynamic penetration tests supports the development of safer and more efficient geotechnical engineering solutions, reinforcing the role of geotechnics in modern civil engineering challenges.
- 5 November 2025
- Published by Polish Mineral Engineering Society in Inżynieria Mineralna
- Vol. 2 (2)
Open AccessIntegrated Characterization Using SCPTu, CPTu, and Dynamic Penetration Tests for Geotechnical Sustainability
The present study focuses on the geotechnical characterization of a rock mass in Covilhã (Portugal) using in situ testing techniques. The research aims to enhance the understanding of subsurface conditions by integrating multiple geotechnical investigation methods, including the seismic piezocone penetration test with pore pressure measurements (SCPTu), without seismic (CPTu), dynamic penetration tests (DPM and DPSH). These tests provide critical data on soil mechanical resistance, internal structure, and deformation properties, supporting more accurate foundation and infrastructure design decisions. The results indicate that the studied soil primarily consists of sand to silty sand with high and increasing over consolidated ratio and relative density, showing a trend towards cementation. The SCPTu test proved highly effective in assessing initial stiffness and computing deformation moduli, significantly contributing to geotechnical engineering applications. Additionally, DPM and DPSH have provided complementary data, allowing for a more comprehensive evaluation of subsurface variability. The integration of these methods enhanced the reliability of soil classification, ensuring robust datasets for geotechnical analysis and infrastructure development. This research aligns with the themes of in - situ testing for geotechnical development. The findings emphasize the importance of multidisciplinary approaches in advancing infrastructure resilience and sustainability through accurate subsurface characterization. The combination of SCPTu, CPTu, and dynamic penetration tests supports the development of safer and more efficient geotechnical engineering solutions, reinforcing the role of geotechnics in modern civil engineering challenges.
- Open Access
- 4 September 2025
- Published by MDPI AG in Geotechnics
- Vol. 5 (3) , 62
Erosion, Mechanical and Microstructural Evolution of Cement Stabilized Coarse Soil for Embankments
Internal erosion is a significant issue caused by water flow within soils, resulting in structural collapse of hydraulic structures, particularly in coarse soils located near rivers. These soils typically exhibit granulometric instability due to low clay content, resulting in poor hydraulic and mechanical properties. To mitigate this problem, cement treatment is applied as an alternative to soil removal, reducing transportation and storage costs. The hole erosion test (HET) and Crumbs tests, shearing behaviour through consolidated undrained (CU) triaxial, and microstructure analyses regarding scanning electron microscopy (SEM), mercury intrusion porosimeter (MIP) and thermogravimetric analysis (TGA) were conducted for untreated and treated coarse soil specimens with varying cement contents (1%, 2%, and 3%) and curing durations (1, 7, and 28 days). The findings indicate a reduction in the loss of eroded particles and overall stability of treated soils, along with an improvement in mechanical properties. SEM observations reveal the development of hydration gel after treatment, which enhances cohesion within the soil matrix, corroborated by TGA analyses. MIP reveals the formation of a new class of pores, accompanied by a reduction in dry density. This study demonstrates that low cement addition can transform locally unsuitable soils into durable construction materials, reducing environmental impact and supporting sustainable development.
- 4 September 2025
- Published by MDPI AG in Geotechnics
- Vol. 5 (3) , 62
Open AccessErosion, Mechanical and Microstructural Evolution of Cement Stabilized Coarse Soil for Embankments
Internal erosion is a significant issue caused by water flow within soils, resulting in structural collapse of hydraulic structures, particularly in coarse soils located near rivers. These soils typically exhibit granulometric instability due to low clay content, resulting in poor hydraulic and mechanical properties. To mitigate this problem, cement treatment is applied as an alternative to soil removal, reducing transportation and storage costs. The hole erosion test (HET) and Crumbs tests, shearing behaviour through consolidated undrained (CU) triaxial, and microstructure analyses regarding scanning electron microscopy (SEM), mercury intrusion porosimeter (MIP) and thermogravimetric analysis (TGA) were conducted for untreated and treated coarse soil specimens with varying cement contents (1%, 2%, and 3%) and curing durations (1, 7, and 28 days). The findings indicate a reduction in the loss of eroded particles and overall stability of treated soils, along with an improvement in mechanical properties. SEM observations reveal the development of hydration gel after treatment, which enhances cohesion within the soil matrix, corroborated by TGA analyses. MIP reveals the formation of a new class of pores, accompanied by a reduction in dry density. This study demonstrates that low cement addition can transform locally unsuitable soils into durable construction materials, reducing environmental impact and supporting sustainable development.