D. B. Jabaraj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
D. B. Jabaraj has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Venkatagiri Krishnamoorthy Bupesh Raja
Department of Mechanical Engineering , Sathyabama Institute of Science and Technology , Chennai , Tamil Nadu , India
4 shared publications D. Mohan Lal
3 shared publications- Jayapriya Jayaprakash
Department of Applied Science and Technology, Anna University, Chennai, India
3 shared publications - A. Subrammanian
Department of Mechanical Engineering, St Peters University, Avadi, Chennai- 600054, Tamil Nadu
2 shared publications A. Narendran
1 shared publicationA. Subrammanian
Department of Mechanical Engineering, St Peters University, Avadi, Chennai - 600054, Tamil Nadu
1 shared publication
Latest Publications
- Open Access
- 24 November 2016
- Published by Indian Society for Education and Environment in Indian Journal of Science and Technology
- Vol. 9 (43)
Experimental Investigation of DSS/HRS GTAW Weldments
Objectives: The Gas Tungsten Arc Welding (GTAW) of blanks 2 mm thick of Duplex Stainless Steel (DSS) and Hot Rolled Medium and High Tensile Structural Steel (HRS) is carried out to investigate the metallurgical, mechanical properties and the fracture. Methods: The characterization of the weldments involves tests, viz. macrostructure, microstructure, micro composition analysis through Energy Dispersive Analysis of X ray (EDAX) to find out the metallurgical properties and micro hardness test, tensile test, bend test to determine the mechanical properties of the weldments. Topography of tensile test fractured specimens was analyzed with the help of Scanning Electron Microscope (SEM) and determines the influence of the welding on the ductility of the weld material. Findings: The increase in the weld zone micro hardness and formation of dendritic delta ferrite microstructure, when compared with the DSS parent metal having elongated grained austenite with ferrite and the HRS parent metal having fine grains of ferrite, caused the joint efficiency of the DSS/HRS weldment to increase. The Energy Dispersive Analysis of X ray (EDAX) indicates the formation of dendritic delta ferrite microstructure is attributed to the presence of elements like Si and Cr. The SEM fractography analysis indicates that the weldments possess good tensile strength without decrease in ductility of the fusion zone. Applications: Experimental investigation of mechanical properties and microstructure of DSS-HRS dissimilar GTAW weld joints and fracture analysis with EDAX to identify the changes in the chemical compositions of the fractured specimen.
- 24 November 2016
- Published by Indian Society for Education and Environment in Indian Journal of Science and Technology
- Vol. 9 (43)
Open AccessExperimental Investigation of DSS/HRS GTAW Weldments
Objectives: The Gas Tungsten Arc Welding (GTAW) of blanks 2 mm thick of Duplex Stainless Steel (DSS) and Hot Rolled Medium and High Tensile Structural Steel (HRS) is carried out to investigate the metallurgical, mechanical properties and the fracture. Methods: The characterization of the weldments involves tests, viz. macrostructure, microstructure, micro composition analysis through Energy Dispersive Analysis of X ray (EDAX) to find out the metallurgical properties and micro hardness test, tensile test, bend test to determine the mechanical properties of the weldments. Topography of tensile test fractured specimens was analyzed with the help of Scanning Electron Microscope (SEM) and determines the influence of the welding on the ductility of the weld material. Findings: The increase in the weld zone micro hardness and formation of dendritic delta ferrite microstructure, when compared with the DSS parent metal having elongated grained austenite with ferrite and the HRS parent metal having fine grains of ferrite, caused the joint efficiency of the DSS/HRS weldment to increase. The Energy Dispersive Analysis of X ray (EDAX) indicates the formation of dendritic delta ferrite microstructure is attributed to the presence of elements like Si and Cr. The SEM fractography analysis indicates that the weldments possess good tensile strength without decrease in ductility of the fusion zone. Applications: Experimental investigation of mechanical properties and microstructure of DSS-HRS dissimilar GTAW weld joints and fracture analysis with EDAX to identify the changes in the chemical compositions of the fractured specimen.
- Open Access
- 17 November 2016
- Published by Indian Society for Education and Environment in Indian Journal of Science and Technology
- Vol. 9 (42)
Mechanical Properties and Phase Transformations in Resistance Spot Welded Dissimilar Joints of AISI409M/AISI301 Steel
Objectives: This study aims to investigate the mechanical properties and phase transformations in dissimilar metal joints between AISI 301 Austenitic Stainless Steel and AISI 409M Ferritic Stainless Steel, joined by resistance spot welding. Methods/Analysis: Mechanical properties such as tensile shear strength, failure energy, failure mode, nugget size and surface indentation were analysed at varying current ratings. Macrostructure was examined for size and shape. Microstructure at various locations such as, fusion zone and heat affected zones were investigated. Micro hardness measurement was done at various locations along the weld. Findings: Peak load incremented progressively with rise in welding current, till the commencement of severe expulsion. Weld zone hardness showed a higher value than that of nearby heat affected zones and parent metals. Increment in welding current resulted in enlargement of weld nugget and rise in energy absorption capacity. Electrode indentation values were seen to be correlated with welding current values positively. Fusion zone microstructure consists of marten site and ferrite. Asymmetrical nugget shape was observed. Novelty/Improvement: This study explores the properties, both mechanical and microstructure of AISI 409M-AISI 301 steel dissimilar joint, joined by resistance spot welding.
- 17 November 2016
- Published by Indian Society for Education and Environment in Indian Journal of Science and Technology
- Vol. 9 (42)
Open AccessMechanical Properties and Phase Transformations in Resistance Spot Welded Dissimilar Joints of AISI409M/AISI301 Steel
Objectives: This study aims to investigate the mechanical properties and phase transformations in dissimilar metal joints between AISI 301 Austenitic Stainless Steel and AISI 409M Ferritic Stainless Steel, joined by resistance spot welding. Methods/Analysis: Mechanical properties such as tensile shear strength, failure energy, failure mode, nugget size and surface indentation were analysed at varying current ratings. Macrostructure was examined for size and shape. Microstructure at various locations such as, fusion zone and heat affected zones were investigated. Micro hardness measurement was done at various locations along the weld. Findings: Peak load incremented progressively with rise in welding current, till the commencement of severe expulsion. Weld zone hardness showed a higher value than that of nearby heat affected zones and parent metals. Increment in welding current resulted in enlargement of weld nugget and rise in energy absorption capacity. Electrode indentation values were seen to be correlated with welding current values positively. Fusion zone microstructure consists of marten site and ferrite. Asymmetrical nugget shape was observed. Novelty/Improvement: This study explores the properties, both mechanical and microstructure of AISI 409M-AISI 301 steel dissimilar joint, joined by resistance spot welding.
- Open Access
- 10 November 2016
- Published by Indian Society for Education and Environment in Indian Journal of Science and Technology
- Vol. 9 (41)
Mechanical Properties and Phase Transformations in Resistance Spot Welded Dissimilar Joints of AISI409M/AISI301 Steel
Objectives: In this study, the mechanical properties and phase transformations of resistance spot welded dissimilar joints between austenitic stainless steel AISI 301 and ferity stainless steel AISI 409M are investigated. Methods/Analysis: Mechanical properties such as tensile shear strength, failure energy, failure mode, nugget size and surface indentation were analysed at varying current ratings. Macrostructure was examined for size and shape. Microstructure at various locations such as, fusion zone and heat affected zones were investigated. Micro hardness measurement was done at various locations along the weld. Findings: Tensile shear strength increases with increase in welding current in expulsion free welds. Fusion zone hardness was found to be larger than that of both base metals and heat affected zones. Nugget size and energy absorbing capacity of the spot weld were found to be in correlation with weld current in expulsion free samples. Electrode indentation on the nugget surface increases with increase in welding current. Fusion zone microstructure consists of martensite and ferrite. Asymmetrical nugget shape was observed. Novelty/Improvement: Investigating the effects of resistance spot welding on the mechanical properties and phase transformations of ferritic-austenitic dissimilar metal weld joint.
- 10 November 2016
- Published by Indian Society for Education and Environment in Indian Journal of Science and Technology
- Vol. 9 (41)
Open AccessMechanical Properties and Phase Transformations in Resistance Spot Welded Dissimilar Joints of AISI409M/AISI301 Steel
Objectives: In this study, the mechanical properties and phase transformations of resistance spot welded dissimilar joints between austenitic stainless steel AISI 301 and ferity stainless steel AISI 409M are investigated. Methods/Analysis: Mechanical properties such as tensile shear strength, failure energy, failure mode, nugget size and surface indentation were analysed at varying current ratings. Macrostructure was examined for size and shape. Microstructure at various locations such as, fusion zone and heat affected zones were investigated. Micro hardness measurement was done at various locations along the weld. Findings: Tensile shear strength increases with increase in welding current in expulsion free welds. Fusion zone hardness was found to be larger than that of both base metals and heat affected zones. Nugget size and energy absorbing capacity of the spot weld were found to be in correlation with weld current in expulsion free samples. Electrode indentation on the nugget surface increases with increase in welding current. Fusion zone microstructure consists of martensite and ferrite. Asymmetrical nugget shape was observed. Novelty/Improvement: Investigating the effects of resistance spot welding on the mechanical properties and phase transformations of ferritic-austenitic dissimilar metal weld joint.
- 21 May 2015
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 69 (3) , 767-774
Mechanical Properties and Microstructure of Resistance Spot Welded Joints of AISI 409M Ferritic Stainless Steel
- 21 May 2015
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 69 (3) , 767-774
Mechanical Properties and Microstructure of Resistance Spot Welded Joints of AISI 409M Ferritic Stainless Steel
- 31 March 2007
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 46 (3) , 276-283
Evolving an optimal composition of HFC407C/HC290/HC600a mixture as an alternative to HCFC22 in window air conditioners
- 31 March 2007
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 46 (3) , 276-283
Evolving an optimal composition of HFC407C/HC290/HC600a mixture as an alternative to HCFC22 in window air conditioners
- 1 October 2006
- Published by Elsevier in Applied Thermal Engineering
- Vol. 26 (14-15) , 1621-1628
Flow characteristics of HFC407C/HC600a/HC290 refrigerant mixture in adiabatic capillary tubes
- 1 October 2006
- Published by Elsevier in Applied Thermal Engineering
- Vol. 26 (14-15) , 1621-1628
Flow characteristics of HFC407C/HC600a/HC290 refrigerant mixture in adiabatic capillary tubes
- 1 September 2006
- Published by Elsevier in Energy Conversion and Management
- Vol. 47 (15-16) , 2578-2590
Experimental investigation of HFC407C/HC290/HC600a mixture in a window air conditioner
- 1 September 2006
- Published by Elsevier in Energy Conversion and Management
- Vol. 47 (15-16) , 2578-2590
Experimental investigation of HFC407C/HC290/HC600a mixture in a window air conditioner