Longfei Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Longfei Zhang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Zaiqiang Hu
School of Civil Engineering and Architecture, Xi’an University of Technology, Xi’an 710048, China
7 shared publications - Xiaoliang Wang
School of Civil Engineering and Architecture, Xi’an University of Technology, Xi’an 710048, China
6 shared publications - Haicheng She
School of Urban Construction, Yangtze University, Jingzhou 434032, China
5 shared publications - Hongru Li
School of Civil Engineering and Architecture, Xi’an University of Technology, Xi’an 710048, China
5 shared publications - Xiaoning Han
Institute of Geotechnical Engineering, Xi’an University of Technology, Xi’an 710048, China
5 shared publications - Xi Yang
Institute of Geotechnical Engineering, Xi’an University of Technology, Xi’an 710048, China
3 shared publications
Latest Publications
- Open Access
- 1 January 2024
- Published by Wiley in Advances in Civil Engineering
- Vol. 2024 (1)
Water Sensitivity and Structural Properties of Loess
Loess has unique water sensitivity due to its distinct formation environment. The structure of loess is undercompactness, weak cementation, and porousness. The water sensitivity of loess directly leads to many environmental problems and geological hazards, including subgrade subsidences, slope collapse or failures, and building cracking. To reveal the relationship between water sensitivity and loess structure, confined‐compression collapsibility tests and triaxial‐collapsibility tests were performed on loess in different areas. The collapsibility coefficient, porosity ratio, and collapsibility rate were analyzed. Results show that the collapsibility process of loess can be divided into three stages: wetting, softening, and settling. The collapsibility sensitivity of loess is determined primarily by its structural and hydraulic state.
- 1 January 2024
- Published by Wiley in Advances in Civil Engineering
- Vol. 2024 (1)
Open AccessWater Sensitivity and Structural Properties of Loess
Loess has unique water sensitivity due to its distinct formation environment. The structure of loess is undercompactness, weak cementation, and porousness. The water sensitivity of loess directly leads to many environmental problems and geological hazards, including subgrade subsidences, slope collapse or failures, and building cracking. To reveal the relationship between water sensitivity and loess structure, confined‐compression collapsibility tests and triaxial‐collapsibility tests were performed on loess in different areas. The collapsibility coefficient, porosity ratio, and collapsibility rate were analyzed. Results show that the collapsibility process of loess can be divided into three stages: wetting, softening, and settling. The collapsibility sensitivity of loess is determined primarily by its structural and hydraulic state.
- Open Access
- 1 January 2024
- Published by Wiley in Advances in Civil Engineering
- Vol. 2024 (1)
Mechanical Characteristics of Tailings in Different Depositional Zones: A Case Study of Caijiagou Tailings Pond in Shaanxi, China
This study examines the widespread practice of upstream tailings dam construction in metallurgical mines in China, conducting comprehensive testing and research on tailings from various depositional zones of the Caijiagou tailings pond. Analysis of the test results from three types of tailings reveals a systematic relationship between the mechanical characteristics of tailings and their depositional zones: the farther from the dam, the finer the tailings particles, categorized as silty clay tailing, silt tailing, and sandy silt tailing. Consistent patterns were observed in the consolidated‐drained shear strength and consolidated‐undrained effective shear strength of these tailings. Among these, sandy silt tailing exhibited the highest strength, whereas silty clay tailing displayed the lowest. The dynamic stress–strain relationships of all three tailings types are described using the Hardin equivalent viscous‐elastic model, where the initial dynamic shear modulus and the maximum dynamic shear stress in the model increased with effective confining pressure. The damping ratios exhibited a three‐stage trend with increasing dynamic strain: gradual increase, rapid growth, and then gradual stabilization. Under various consolidated stress conditions, the ratio of the damping ratio to the maximum damping ratio versus the reduction in dynamic shear modulus showed a favorable linear relationship. Under vibration conditions, the dynamic shear stress corresponding to tailings failure increased with higher effective confining pressure and consolidated stress ratio. Finally, this study summarizes the parameters and indicators related to the saturated tailings of iron mines used in the research. Our work provides a foundation and reference for the design of tailings dams and the development and utilization of abandoned tailings ponds.
- 1 January 2024
- Published by Wiley in Advances in Civil Engineering
- Vol. 2024 (1)
Open AccessMechanical Characteristics of Tailings in Different Depositional Zones: A Case Study of Caijiagou Tailings Pond in Shaanxi, China
This study examines the widespread practice of upstream tailings dam construction in metallurgical mines in China, conducting comprehensive testing and research on tailings from various depositional zones of the Caijiagou tailings pond. Analysis of the test results from three types of tailings reveals a systematic relationship between the mechanical characteristics of tailings and their depositional zones: the farther from the dam, the finer the tailings particles, categorized as silty clay tailing, silt tailing, and sandy silt tailing. Consistent patterns were observed in the consolidated‐drained shear strength and consolidated‐undrained effective shear strength of these tailings. Among these, sandy silt tailing exhibited the highest strength, whereas silty clay tailing displayed the lowest. The dynamic stress–strain relationships of all three tailings types are described using the Hardin equivalent viscous‐elastic model, where the initial dynamic shear modulus and the maximum dynamic shear stress in the model increased with effective confining pressure. The damping ratios exhibited a three‐stage trend with increasing dynamic strain: gradual increase, rapid growth, and then gradual stabilization. Under various consolidated stress conditions, the ratio of the damping ratio to the maximum damping ratio versus the reduction in dynamic shear modulus showed a favorable linear relationship. Under vibration conditions, the dynamic shear stress corresponding to tailings failure increased with higher effective confining pressure and consolidated stress ratio. Finally, this study summarizes the parameters and indicators related to the saturated tailings of iron mines used in the research. Our work provides a foundation and reference for the design of tailings dams and the development and utilization of abandoned tailings ponds.
- Open Access
- 27 October 2023
- Published by Wiley in Advances in Civil Engineering
- Vol. 2023, 1-13
Mechanical Properties and Mesostructure Evolution of Fibre-Reinforced Loess under Freeze-Thaw Cycles
The strength of loess in seasonal frozen soil areas decreases evidently due to the freeze-thaw cycle, which even leads to some engineering and geological problems. Fibre reinforcement is very effective in improving the mechanical properties of soil. Triaxial tests under different water contents, freezing temperatures, and number of freeze-thaw cycles were carried out for fibre-reinforced loess to study the ability of fibre reinforcement to improve the resistance of loess to freeze-thaw damage; scanning electron microscopy (SEM) was also conducted. The effects of freeze and thaw deterioration and reinforcement were discussed by comparing the strength parameters under different test conditions, and the influence mechanism of freezing temperature, number of freeze-thaw cycles, and reinforcement on loess strength was explained. Results show that a lower freezing temperature indicates a more evident decrease in strength after thawing. Under the action of the first five freeze-thaw cycles, the degree of decrease is more prominent. The fibre reinforcement can reduce the fragmentation of aggregates in loess, thereby effectively restraining the deterioration effect of loess during freeze-thaw cycles. Finally, the strength parameter prediction model under different freeze-thaw cycles of reinforced loess is established, thereby providing theoretical support for engineering application and numerical simulation of fibre-reinforced loess.
- 27 October 2023
- Published by Wiley in Advances in Civil Engineering
- Vol. 2023, 1-13
Open AccessMechanical Properties and Mesostructure Evolution of Fibre-Reinforced Loess under Freeze-Thaw Cycles
The strength of loess in seasonal frozen soil areas decreases evidently due to the freeze-thaw cycle, which even leads to some engineering and geological problems. Fibre reinforcement is very effective in improving the mechanical properties of soil. Triaxial tests under different water contents, freezing temperatures, and number of freeze-thaw cycles were carried out for fibre-reinforced loess to study the ability of fibre reinforcement to improve the resistance of loess to freeze-thaw damage; scanning electron microscopy (SEM) was also conducted. The effects of freeze and thaw deterioration and reinforcement were discussed by comparing the strength parameters under different test conditions, and the influence mechanism of freezing temperature, number of freeze-thaw cycles, and reinforcement on loess strength was explained. Results show that a lower freezing temperature indicates a more evident decrease in strength after thawing. Under the action of the first five freeze-thaw cycles, the degree of decrease is more prominent. The fibre reinforcement can reduce the fragmentation of aggregates in loess, thereby effectively restraining the deterioration effect of loess during freeze-thaw cycles. Finally, the strength parameter prediction model under different freeze-thaw cycles of reinforced loess is established, thereby providing theoretical support for engineering application and numerical simulation of fibre-reinforced loess.
- Open Access
Dynamic Characteristics of Asphalt Concrete as an Impervious Core in Embankment Dams under Varying Temperatures and Stress States
To reveal the dynamic characteristics of asphalt core embankment dams (ACEDs), we carried out a dynamic triaxial experiment on hydraulic asphalt concrete (HAC) under different temperatures (T = 4 °C, 10 °C, 16 °C, and 22 °C) and stress states (Kc = 1.0, 1.2, 1.4, and 1.6; σ3 = 0.5, 0.6, 0.7, and 0.8 MPa). The results indicate that HAC’s maximum dynamic elastic modulus increased with decreasing temperature, increasing principal stress ratio, and increasing confining pressure. However, the damping ratio showed the opposite trend. Moreover, in order to study the deformation capacity of HAC, 300 cyclic loads were applied to some specimens. At a temperature of 22 °C, the specimens had a tendency to deform axially, but not significantly. With a decrease in temperature, the axial deformation tendency of the specimen gradually weakened or even disappeared. However, a small number of cracks appeared in the aggregate and between the asphalt and the aggregate of the specimen. In order to quantify the dependence of dynamic parameters on temperature, the temperature influence factor of the maximum dynamic elastic modulus and the temperature sensing factor of the damping ratio were defined. The variation in the temperature influence factor of the maximum dynamic elastic modulus with temperature can be described by a logistic function. The temperature sensing factor of the damping ratio increased with an increasing principal stress ratio and peripheral pressure. Finally, maximum dynamic elastic modulus and damping ratio computational models for the interaction of temperatures and stress states were developed using the normalization method. Upon comparison, the dynamic parameters were observed to be very close to those listed in the literature, which verifies the applicability of the computational models of the maximum dynamic elastic modulus and damping ratio.
Open AccessDynamic Characteristics of Asphalt Concrete as an Impervious Core in Embankment Dams under Varying Temperatures and Stress States
To reveal the dynamic characteristics of asphalt core embankment dams (ACEDs), we carried out a dynamic triaxial experiment on hydraulic asphalt concrete (HAC) under different temperatures (T = 4 °C, 10 °C, 16 °C, and 22 °C) and stress states (Kc = 1.0, 1.2, 1.4, and 1.6; σ3 = 0.5, 0.6, 0.7, and 0.8 MPa). The results indicate that HAC’s maximum dynamic elastic modulus increased with decreasing temperature, increasing principal stress ratio, and increasing confining pressure. However, the damping ratio showed the opposite trend. Moreover, in order to study the deformation capacity of HAC, 300 cyclic loads were applied to some specimens. At a temperature of 22 °C, the specimens had a tendency to deform axially, but not significantly. With a decrease in temperature, the axial deformation tendency of the specimen gradually weakened or even disappeared. However, a small number of cracks appeared in the aggregate and between the asphalt and the aggregate of the specimen. In order to quantify the dependence of dynamic parameters on temperature, the temperature influence factor of the maximum dynamic elastic modulus and the temperature sensing factor of the damping ratio were defined. The variation in the temperature influence factor of the maximum dynamic elastic modulus with temperature can be described by a logistic function. The temperature sensing factor of the damping ratio increased with an increasing principal stress ratio and peripheral pressure. Finally, maximum dynamic elastic modulus and damping ratio computational models for the interaction of temperatures and stress states were developed using the normalization method. Upon comparison, the dynamic parameters were observed to be very close to those listed in the literature, which verifies the applicability of the computational models of the maximum dynamic elastic modulus and damping ratio.
- Open Access
- 25 July 2023
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 19
Impact of water delivery pipeline leakage on collapsible loess foundations and treatment methods
- 25 July 2023
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 19
Open AccessImpact of water delivery pipeline leakage on collapsible loess foundations and treatment methods
- Open Access
- 30 June 2023
- Published by Wiley in Advances in Civil Engineering
- Vol. 2023, 1-18
Hazards and Treatment of Collapsible Loess Foundation on Ultrahigh Voltage Transmission Lines
With the development of ultrahigh voltage transmission line construction in northwest China, an increasing number of overhead transmission lines are crossing the loess regions. Ensuring the stability of electricity transmission towers and mitigating the risk of collapse are crucial prerequisites for the construction of transmission lines. Taking the 750 kV demonstration electricity transmission line in Guanting–Lanzhou East as an example, representative loess samples were selected for compression and collapsing sensitivity tests. Four foundation treatment schemes were designed, and the wetting deformation characteristics were investigated through numerical simulation of the rainfall infiltration process. Corresponding optimisation schemes were proposed. The collapsing process was divided into four stages through laboratory collapsing tests. The relationship function between saturation and the Duncan–Chang model parameters of loess was established, which was introduced into the finite element model to consider the rainfall infiltration process. The analysis of the displacement field, and loess saturation field with time after rainfall infiltration for the four schemes showed that adding a lime-stabilised soil cushion layer and waterproof layer to the inclined column foundation had the best effect. Given that the design scheme needs to consider safety and economy, the thickness of the cushion layer was optimised, thereby reducing the use of lime-stabilised soil by 20%. Research findings provide meaningful guidance for the design of transmission tower foundations in loess areas.
- 30 June 2023
- Published by Wiley in Advances in Civil Engineering
- Vol. 2023, 1-18
Open AccessHazards and Treatment of Collapsible Loess Foundation on Ultrahigh Voltage Transmission Lines
With the development of ultrahigh voltage transmission line construction in northwest China, an increasing number of overhead transmission lines are crossing the loess regions. Ensuring the stability of electricity transmission towers and mitigating the risk of collapse are crucial prerequisites for the construction of transmission lines. Taking the 750 kV demonstration electricity transmission line in Guanting–Lanzhou East as an example, representative loess samples were selected for compression and collapsing sensitivity tests. Four foundation treatment schemes were designed, and the wetting deformation characteristics were investigated through numerical simulation of the rainfall infiltration process. Corresponding optimisation schemes were proposed. The collapsing process was divided into four stages through laboratory collapsing tests. The relationship function between saturation and the Duncan–Chang model parameters of loess was established, which was introduced into the finite element model to consider the rainfall infiltration process. The analysis of the displacement field, and loess saturation field with time after rainfall infiltration for the four schemes showed that adding a lime-stabilised soil cushion layer and waterproof layer to the inclined column foundation had the best effect. Given that the design scheme needs to consider safety and economy, the thickness of the cushion layer was optimised, thereby reducing the use of lime-stabilised soil by 20%. Research findings provide meaningful guidance for the design of transmission tower foundations in loess areas.
- Open Access
- 8 June 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (12) , 9280
Influence of Dry-Wet Cycles on the Structure and Shear Strength of Loess
The dry-wet cycle is an important factor that causes slope instability and foundation settlement in loess regions. In order to study the effects of the dry-wet cycle on the structure and shear strength of loess, isotropic compression tests and triaxial shear tests were carried out on loess with different numbers of dry-wet cycles. The results show that the dry-wet cycles mainly reduce the cohesion of loess, and the most obvious decline is after the first cycle; however, they have no effect on the angle of internal friction of loess. The structural yield strength and structural parameters of loess can represent the structure of loess well, which gradually decrease with the increase in the number dry-wet cycles and water content. The initial yield surface is approximately an ellipse, which gradually shrinks with the increase in water content and dry-wet cycles. The structure and cohesion of loess have similar changes, and there is an obvious exponential function relationship between them.
- 8 June 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (12) , 9280
Open AccessInfluence of Dry-Wet Cycles on the Structure and Shear Strength of Loess
The dry-wet cycle is an important factor that causes slope instability and foundation settlement in loess regions. In order to study the effects of the dry-wet cycle on the structure and shear strength of loess, isotropic compression tests and triaxial shear tests were carried out on loess with different numbers of dry-wet cycles. The results show that the dry-wet cycles mainly reduce the cohesion of loess, and the most obvious decline is after the first cycle; however, they have no effect on the angle of internal friction of loess. The structural yield strength and structural parameters of loess can represent the structure of loess well, which gradually decrease with the increase in the number dry-wet cycles and water content. The initial yield surface is approximately an ellipse, which gradually shrinks with the increase in water content and dry-wet cycles. The structure and cohesion of loess have similar changes, and there is an obvious exponential function relationship between them.