Mohammad Nabi Newaz Khan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mohammad Nabi Newaz Khan has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Maslina Jamil
Sustainable Construction Materials and Building Systems (SUCOMBS) Research Group, Faculty of Engineering & Built Environment, Universiti Kebangsaan Malaysia (UKM), UKM Bangi, Malaysia
2 shared publications - Rezaul Karim
Department of Civil Engineering, Dhaka University of Engineering and Technology, Gazipur 1700, Bangladesh
2 shared publications - A. B. M. Amrul Kaish
Universiti Kebangsaan Malaysia
1 shared publication - Faiz Uddin Ahmed Shaikh
School of Civil and Mechanical Engineering, Curtin University
1 shared publication - Fook Chuan Lai
Sika Kimia Sendirian Berhad, Nilai, Negeri Sembilan Dk 71800, Malaysia
1 shared publication - Jhutan Chandra Kuri
PhD in Civil Engineering, School of Civil and Mechanical Engineering, Curtin University, Perth, WA, Australia
1 shared publication
Latest Publications
- 1 June 2023
- Published by Emerald Publishing in Advances in Cement Research
- Vol. 35 (6) , 248-257
Acid resistance of alkali-activated composites containing waste glass as fine aggregate
This study examined the efficacy of waste glass cullet (WGC) as a substitute for natural fine aggregate in alkali-activated composites when exposed to sulfuric acid and hydrochloric acid solutions for 1 year. The physical appearance, surface alkalinity, mass, mechanical strength and microstructure of hardened samples before and after immersion in acid solutions were investigated. The findings this work indicated that physical, mechanical and microstructural damage of the specimens due to acid attack increased with an increase in the percentage of WGC. This was attributed to the smooth surface texture and angularity of the WGC, which affected the bond with the damaged paste matrix at the interfacial transition zone and increased the porosity. However, the acid resistance of the mortars containing up to 50% WGC was found to be satisfactory when compared with the mortar without WGC. Therefore, the use of WGC as a partial replacement (up to 50%) for natural sand is feasible for alkali-activated systems under acid exposure.
- 1 June 2023
- Published by Emerald Publishing in Advances in Cement Research
- Vol. 35 (6) , 248-257
Acid resistance of alkali-activated composites containing waste glass as fine aggregate
This study examined the efficacy of waste glass cullet (WGC) as a substitute for natural fine aggregate in alkali-activated composites when exposed to sulfuric acid and hydrochloric acid solutions for 1 year. The physical appearance, surface alkalinity, mass, mechanical strength and microstructure of hardened samples before and after immersion in acid solutions were investigated. The findings this work indicated that physical, mechanical and microstructural damage of the specimens due to acid attack increased with an increase in the percentage of WGC. This was attributed to the smooth surface texture and angularity of the WGC, which affected the bond with the damaged paste matrix at the interfacial transition zone and increased the porosity. However, the acid resistance of the mortars containing up to 50% WGC was found to be satisfactory when compared with the mortar without WGC. Therefore, the use of WGC as a partial replacement (up to 50%) for natural sand is feasible for alkali-activated systems under acid exposure.
- Open Access
- 1 January 2017
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 21 (1) , 274-284
Filler effect of pozzolanic materials on the strength and microstructure development of mortar
- 1 January 2017
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 21 (1) , 274-284
Open AccessFiller effect of pozzolanic materials on the strength and microstructure development of mortar
- Open Access
On the Utilization of Pozzolanic Wastes as an Alternative Resource of Cement
Recently, as a supplement of cement, the utilization of pozzolanic materials in cement and concrete manufacturing has increased significantly. This study investigates the scope to use pozzolanic wastes (slag, palm oil fuel ash and rice husk ash) as an alkali activated binder (AAB) that can be used as an alternative to cement. To activate these materials, sodium hydroxide solution was used at 1.0, 2.5 and 5.0 molar concentration added into the mortar, separately. The required solution was used to maintain the flow of mortar at 110% ± 5%. The consistency and setting time of the AAB-paste were determined. Mortar was tested for its flow, compressive strength, porosity, water absorption and thermal resistance (heating at 700 °C) and investigated by scanning electron microscopy. The experimental results reveal that AAB-mortar exhibits less flow than that of ordinary Portland cement (OPC). Surprisingly, AAB-mortars (with 2.5 molar solution) achieved a compressive strength of 34.3 MPa at 28 days, while OPC shows that of 43.9 MPa under the same conditions. Although water absorption and porosity of the AAB-mortar are slightly high, it shows excellent thermal resistance compared to OPC. Therefore, based on the test results, it can be concluded that in the presence of a chemical activator, the aforementioned pozzolans can be used as an alternative material for cement.
Open AccessOn the Utilization of Pozzolanic Wastes as an Alternative Resource of Cement
Recently, as a supplement of cement, the utilization of pozzolanic materials in cement and concrete manufacturing has increased significantly. This study investigates the scope to use pozzolanic wastes (slag, palm oil fuel ash and rice husk ash) as an alkali activated binder (AAB) that can be used as an alternative to cement. To activate these materials, sodium hydroxide solution was used at 1.0, 2.5 and 5.0 molar concentration added into the mortar, separately. The required solution was used to maintain the flow of mortar at 110% ± 5%. The consistency and setting time of the AAB-paste were determined. Mortar was tested for its flow, compressive strength, porosity, water absorption and thermal resistance (heating at 700 °C) and investigated by scanning electron microscopy. The experimental results reveal that AAB-mortar exhibits less flow than that of ordinary Portland cement (OPC). Surprisingly, AAB-mortars (with 2.5 molar solution) achieved a compressive strength of 34.3 MPa at 28 days, while OPC shows that of 43.9 MPa under the same conditions. Although water absorption and porosity of the AAB-mortar are slightly high, it shows excellent thermal resistance compared to OPC. Therefore, based on the test results, it can be concluded that in the presence of a chemical activator, the aforementioned pozzolans can be used as an alternative material for cement.