H. Tanigawa
Research Subjects
Research Interests
H. Tanigawa has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
K. Shiba
Japan Atomic Energy Research Institute, Tokai, Ibaraki 319-1195, Japan, Tel: +81-29-282-6498
2 shared publicationsA Kohyama
Institute of Advanced Energy, Kyoto University, Uji, Kyoto 611-0011, Japan
1 shared publicationM Ando
Japan Atomic Energy Research Institute, 2-4 Shirakata-Shirane, Tokai-Mura, Ibaraki-ken 319-1195, Japan
1 shared publicationM. A. Sokolov
Oak Ridge National Laboratory, Oak Ridge, TN 37831, USA
1 shared publicationM. Ando
Japan Atomic Energy Research Institute, Tokai, Ibaraki 319-1195, Japan, Tel: +81-29-282-6498
1 shared publicationN. Hashimoto
Oak Ridge National Laboratory Oak Ridge, TN 37831-6136, USA
1 shared publication
Latest Publications
- 29 November 2012
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 442 (1-3) , S830-S833
Stability of precipitates in ZIRLO under high energy particle irradiation
- 29 November 2012
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 442 (1-3) , S830-S833
Stability of precipitates in ZIRLO under high energy particle irradiation
- 1 July 2003
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 44 (1) , 219-223
Microstructure and Hardness Variation in a TIG Weldment of Irradiated F82H
Previous work reported that a TIG weld joint of F82H exhibited low irradiation hardening in a tensile test, compared to the base metal. Microhardness tests and microstructure observation on the neutron-irradiated TIG weld joint of F82H revealed that the over-tempered zone in the heat-affected zone (HAZ) exhibited this good performance. The region in the HAZ where the prior austenite grain size became very fine during welding also exhibited lower irradiation hardening. Hypotheses for these low-hardening mechanisms were proposed based on the phase diagram and grain size.
- 1 July 2003
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 44 (1) , 219-223
Microstructure and Hardness Variation in a TIG Weldment of Irradiated F82H
Previous work reported that a TIG weld joint of F82H exhibited low irradiation hardening in a tensile test, compared to the base metal. Microhardness tests and microstructure observation on the neutron-irradiated TIG weld joint of F82H revealed that the over-tempered zone in the heat-affected zone (HAZ) exhibited this good performance. The region in the HAZ where the prior austenite grain size became very fine during welding also exhibited lower irradiation hardening. Hypotheses for these low-hardening mechanisms were proposed based on the phase diagram and grain size.
- 1 July 2003
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 44 (1) , 206-210
Charpy Impact Properties of Reduced-Activation Ferritic/Martensitic Steels Irradiated in HFIR up to 20 dpa
The effects of irradiation up to 20 dpa on the Charpy impact properties of reduced-activation ferritic/martensitic steels (RAFs) were investigated. The ductile-brittle transition temperature (DBTT) of F82H-IEA shifted up to around 323K. TIG weldments of F82H showed a fairly small variation on their impact properties. A finer prior austenite grain size in F82H-IEA after a different heat treatment resulted in a 20K lower DBTT compared to F82H-IEA after the standard heat treatment, and that effect was maintained even after irradiation. Helium effects were investigated utilizing Ni-doped F82H, but no obvious evidence of helium effects was obtained. ORNL9Cr-2WVTa and JLF-1 steels showed smaller DBTT shifts compared to F82H-IEA.
- 1 July 2003
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 44 (1) , 206-210
Charpy Impact Properties of Reduced-Activation Ferritic/Martensitic Steels Irradiated in HFIR up to 20 dpa
The effects of irradiation up to 20 dpa on the Charpy impact properties of reduced-activation ferritic/martensitic steels (RAFs) were investigated. The ductile-brittle transition temperature (DBTT) of F82H-IEA shifted up to around 323K. TIG weldments of F82H showed a fairly small variation on their impact properties. A finer prior austenite grain size in F82H-IEA after a different heat treatment resulted in a 20K lower DBTT compared to F82H-IEA after the standard heat treatment, and that effect was maintained even after irradiation. Helium effects were investigated utilizing Ni-doped F82H, but no obvious evidence of helium effects was obtained. ORNL9Cr-2WVTa and JLF-1 steels showed smaller DBTT shifts compared to F82H-IEA.
- 31 December 2002
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 307-311, 293-298
Microstructural analysis of mechanically tested reduced-activation ferritic/martensitic steels
- 31 December 2002
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 307-311, 293-298
Microstructural analysis of mechanically tested reduced-activation ferritic/martensitic steels