He Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
He Wang has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Shenghong Lei
Southwest Institute of Technical Physics, Chengdu, China
8 shared publications - Yun Cao
Nanjing University of Science and Technology
7 shared publications - Weirong Nie
Nanjing University of Science and Technology
5 shared publications - Mo Yang
Nanjing University of Science and Technology
4 shared publications Zhanwen Xi
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China
4 shared publications- Baolin Cheng
Nanjing University of Science and Technology
3 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (20) , 30217-30228
Study on Overload Resistance Capability of U-Shaped Silicon-Based MEMS Electrothermal Actuators Based on Surface Coating Technology
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (20) , 30217-30228
Study on Overload Resistance Capability of U-Shaped Silicon-Based MEMS Electrothermal Actuators Based on Surface Coating Technology
- 7 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 35 (3) , 582-589
Analysis of Brittle Fracture Characteristics Under Static/Dynamic Loads in Silicon-Based MEMS Cantilevers
Silicon-based MEMS cantilevers are widely used in high-reliability microsystems. Addressing the unclear relationship between the fracture strength of silicon-based MEMS cantilevers under static loads and high-strain-rate dynamic loads, this study investigates the typical cantilever-type setback safety device in fuze MEMS safety and arming devices. A dynamic model of a cantilever with a concentrated mass at the end was established. Through material characterization, static and dynamic loading experiments, and numerical simulations, the fracture response characteristics were systematically examined. The crystal orientation and mechanical parameters of (111)-oriented single-crystal silicon were verified through X-ray diffraction and nanoindentation testing. The critical fracture stress of cantilevers was obtained under quasi-static loading and half-sine acceleration impact loading. The results indicate that the fracture stress under dynamic load is significantly lower than that under static load. The load factor $K$ was introduced to effectively describe the relationship, with an average value of approximately 3.0620. Fracture section analysis further revealed the fundamental differences in crack propagation patterns under varying load conditions. The findings can serve as guidance for the engineering design of silicon-based cantilever.[2026-0027]
- 7 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 35 (3) , 582-589
Analysis of Brittle Fracture Characteristics Under Static/Dynamic Loads in Silicon-Based MEMS Cantilevers
Silicon-based MEMS cantilevers are widely used in high-reliability microsystems. Addressing the unclear relationship between the fracture strength of silicon-based MEMS cantilevers under static loads and high-strain-rate dynamic loads, this study investigates the typical cantilever-type setback safety device in fuze MEMS safety and arming devices. A dynamic model of a cantilever with a concentrated mass at the end was established. Through material characterization, static and dynamic loading experiments, and numerical simulations, the fracture response characteristics were systematically examined. The crystal orientation and mechanical parameters of (111)-oriented single-crystal silicon were verified through X-ray diffraction and nanoindentation testing. The critical fracture stress of cantilevers was obtained under quasi-static loading and half-sine acceleration impact loading. The results indicate that the fracture stress under dynamic load is significantly lower than that under static load. The load factor $K$ was introduced to effectively describe the relationship, with an average value of approximately 3.0620. Fracture section analysis further revealed the fundamental differences in crack propagation patterns under varying load conditions. The findings can serve as guidance for the engineering design of silicon-based cantilever.[2026-0027]
- 27 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (9) , 14893-14901
Topology and Size Optimization of MEMS Electrothermal U-Shaped Actuator
To improve the overloading-resistibility of the electrothermal U-shaped actuator, the paper employs size and topology optimization to realize the multi-objective optimization of the U-shaped actuator. The micro-electro-mechanical system (MEMS) pin puller based on the U-shaped actuator is optimized to verify its effectiveness. The pin of the MEMS pin puller was lightweighted firstly. And the finite element method (FEM) simulation was used to compare the strength and function of MEMS pin puller before and after the pin optimization. After pin optimization, the optimization combining multi-physics field coupled FEM, impact FEM and NSGA-II is established to realize the multi-objective optimization of U-shaped actuator. The radius of the flexure round corner and the mass distribution of the cold arm are used as design variables. And the optimization objectives are the displacement of the pin, the maximum stress of the flexure, and the maximum temperature of actuator. The impact experiment and function experiment of the MEMS pin puller are carried out to verify its overloading-resistibility under impact load and output displacement under driving voltage. The results show that the overloading-resistibility of the optimized MEMS pin puller increased from 9000g to 16100g, with a 78% improvement. The overloading-resistibility of the U-shaped actuator is increased from 9,000g to 20,300g, with a 125% improvement. Meanwhile, the output displacement is reduced from 186μm to 90μm, with a 52% reduction. The response time is not affected. Therefore, the method in this paper is suitable for the optimization of U-shaped actuators under complex conditions. It can provide guidance for improving the overloading-resistibility of U-shaped actuators.
- 27 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (9) , 14893-14901
Topology and Size Optimization of MEMS Electrothermal U-Shaped Actuator
To improve the overloading-resistibility of the electrothermal U-shaped actuator, the paper employs size and topology optimization to realize the multi-objective optimization of the U-shaped actuator. The micro-electro-mechanical system (MEMS) pin puller based on the U-shaped actuator is optimized to verify its effectiveness. The pin of the MEMS pin puller was lightweighted firstly. And the finite element method (FEM) simulation was used to compare the strength and function of MEMS pin puller before and after the pin optimization. After pin optimization, the optimization combining multi-physics field coupled FEM, impact FEM and NSGA-II is established to realize the multi-objective optimization of U-shaped actuator. The radius of the flexure round corner and the mass distribution of the cold arm are used as design variables. And the optimization objectives are the displacement of the pin, the maximum stress of the flexure, and the maximum temperature of actuator. The impact experiment and function experiment of the MEMS pin puller are carried out to verify its overloading-resistibility under impact load and output displacement under driving voltage. The results show that the overloading-resistibility of the optimized MEMS pin puller increased from 9000g to 16100g, with a 78% improvement. The overloading-resistibility of the U-shaped actuator is increased from 9,000g to 20,300g, with a 125% improvement. Meanwhile, the output displacement is reduced from 186μm to 90μm, with a 52% reduction. The response time is not affected. Therefore, the method in this paper is suitable for the optimization of U-shaped actuators under complex conditions. It can provide guidance for improving the overloading-resistibility of U-shaped actuators.
- 28 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (8) , 12711-12721
Failure Behavior Analysis of a Novel Silicon-Based MEMS Setback Safety Device
To improve the reliability and safety of the safety and arming device (S&A), this paper presents a failure analysis of a novel silicon-based MEMS setback safety device with curved zig-zag tracks. The results of the finite element method (FEM) confirm that the setback safety device is effective in detecting and distinguishing impact loads. The strength analysis using FEM simulation identified damage-prone locations. It was determined that micro-spring is more prone to damage than the tooth of the zig-zag track. The failure behavior of the setback safety device has been investigated by impact experiment. 88 times impacts on 57 devices in different directions and magnitude produced the 198 times failure behaviors. The experiments analyze the causes of failure behavior and suggest ways to improve. The study shows that it has two types of failure: function (31.82%) and non-function failures (68.18%). The most main function failures are spring damage and mis-locking, which account for 87.30% of the function failures. The experiment validated the damage prioritization of FEM analysis, indicating that FEM can be used as a preliminary criterion for predicting function failures. It was illustrated that machining errors in tooth height and width of the spring constituted a significant factor in the device's failure, resulting in mis-locking and spring damage. While non-function failures do not affect the basic function of the device and are acceptable without cumulative damage. Finally, a fault tree analysis was performed to summarize the failure behaviors of the setback safety device and the methods for subsequent improvements are proposed.
- 28 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (8) , 12711-12721
Failure Behavior Analysis of a Novel Silicon-Based MEMS Setback Safety Device
To improve the reliability and safety of the safety and arming device (S&A), this paper presents a failure analysis of a novel silicon-based MEMS setback safety device with curved zig-zag tracks. The results of the finite element method (FEM) confirm that the setback safety device is effective in detecting and distinguishing impact loads. The strength analysis using FEM simulation identified damage-prone locations. It was determined that micro-spring is more prone to damage than the tooth of the zig-zag track. The failure behavior of the setback safety device has been investigated by impact experiment. 88 times impacts on 57 devices in different directions and magnitude produced the 198 times failure behaviors. The experiments analyze the causes of failure behavior and suggest ways to improve. The study shows that it has two types of failure: function (31.82%) and non-function failures (68.18%). The most main function failures are spring damage and mis-locking, which account for 87.30% of the function failures. The experiment validated the damage prioritization of FEM analysis, indicating that FEM can be used as a preliminary criterion for predicting function failures. It was illustrated that machining errors in tooth height and width of the spring constituted a significant factor in the device's failure, resulting in mis-locking and spring damage. While non-function failures do not affect the basic function of the device and are acceptable without cumulative damage. Finally, a fault tree analysis was performed to summarize the failure behaviors of the setback safety device and the methods for subsequent improvements are proposed.
- 19 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (15) , 23605-23612
Design and Strength Analysis of a Novel Silicon-Base MEMS Setback Safety Device With Curved Zig-Zag Tracks
To improve the load identification capability and high overloading-resistibility of the silicon-based micro electromechanical system (MEMS) setback safety device, a MEMS setback safety device with curved zig-zag tracks as the primary load identification mechanism is designed in this paper. The dynamic response of the device under launch and drop load is obtained by the finite Element Method (FEM) simulation. The result shows that the setback safety device can effectively identify the launch load and distinguish the service load. Moreover, the strength model of the curved zig-zag tracks in the collision is established by the quasi-static method. The strength model is verified by FEM simulation, and the result is highly consistent with the FEM simulation result. The influence of structure parameters on the strength of zig-zag tracks was analyzed. Moreover, the methods to improve the overloading-resistibility of structure with surfaces collision are given. The impact experiment platform was established by Marchant Hammer and two types of experiments were conducted: (a) Multiple impact with increasing load amplitude on a single device. (b) Single high amplitude impact on the device. The result shows that the device has sufficient strength while being able to effectively differentiate between drop loads.
- 19 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (15) , 23605-23612
Design and Strength Analysis of a Novel Silicon-Base MEMS Setback Safety Device With Curved Zig-Zag Tracks
To improve the load identification capability and high overloading-resistibility of the silicon-based micro electromechanical system (MEMS) setback safety device, a MEMS setback safety device with curved zig-zag tracks as the primary load identification mechanism is designed in this paper. The dynamic response of the device under launch and drop load is obtained by the finite Element Method (FEM) simulation. The result shows that the setback safety device can effectively identify the launch load and distinguish the service load. Moreover, the strength model of the curved zig-zag tracks in the collision is established by the quasi-static method. The strength model is verified by FEM simulation, and the result is highly consistent with the FEM simulation result. The influence of structure parameters on the strength of zig-zag tracks was analyzed. Moreover, the methods to improve the overloading-resistibility of structure with surfaces collision are given. The impact experiment platform was established by Marchant Hammer and two types of experiments were conducted: (a) Multiple impact with increasing load amplitude on a single device. (b) Single high amplitude impact on the device. The result shows that the device has sufficient strength while being able to effectively differentiate between drop loads.
- 19 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (17) , 19073-19081
Dynamic Response of a Cantilever-Type MEMS Setback Arming Device Under Impact Loads
To improve the reliability and safety of the micro-electro-mechanical system (MEMS) safety and arming devices (SAD), this paper investigated the dynamic response of the cantilever-type MEMS setback arming device under impact loads. Based on the modal superposition method, the dynamic response of the structure is analyzed using the Euler-Bernoulli beam theory. The continuous dynamics model considering the self-weight of the cantilever was established. And the established model can obtain the dynamic response of the entire structure under impact loads. Moreover, the influence of structure parameters on the dynamic characteristics was analyzed by theoretical analysis. The results obtained in the theoretical analysis are highly in agreement with the finite element method (FEM) simulation. Furthermore, the maximum displacement and its occurrence time at fundamental frequency are given. The dynamic visualization experiment was employed for the cantilever-type MEMS setback arming device under impact loads. Multiple experiments showed that the established theoretical model is in high agreement with the experimental results. The dynamic response of the cantilever-type MEMS setback arming device under impact loads is significant for improving the reliability and safety of the system. It provides theoretical guidance for the optimization design.
- 19 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (17) , 19073-19081
Dynamic Response of a Cantilever-Type MEMS Setback Arming Device Under Impact Loads
To improve the reliability and safety of the micro-electro-mechanical system (MEMS) safety and arming devices (SAD), this paper investigated the dynamic response of the cantilever-type MEMS setback arming device under impact loads. Based on the modal superposition method, the dynamic response of the structure is analyzed using the Euler-Bernoulli beam theory. The continuous dynamics model considering the self-weight of the cantilever was established. And the established model can obtain the dynamic response of the entire structure under impact loads. Moreover, the influence of structure parameters on the dynamic characteristics was analyzed by theoretical analysis. The results obtained in the theoretical analysis are highly in agreement with the finite element method (FEM) simulation. Furthermore, the maximum displacement and its occurrence time at fundamental frequency are given. The dynamic visualization experiment was employed for the cantilever-type MEMS setback arming device under impact loads. Multiple experiments showed that the established theoretical model is in high agreement with the experimental results. The dynamic response of the cantilever-type MEMS setback arming device under impact loads is significant for improving the reliability and safety of the system. It provides theoretical guidance for the optimization design.
- 13 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (14) , 15469-15478
Research on Structural Failure of MEMS Safety and Arming Device Considering Uncertainty in Fabrication Errors
This paper presents an efficient methodology for assessing the structural failure of microelectromechanical systems (MEMS) used in safety and arming devices (SAD) while taking into account the effect of fabrication errors. The proposed methodology uses statistical characteristics that are assessed using non-intrusive polynomial chaos expansion (PCE) to consider uncertainty. The effectiveness of the methodology is demonstrated by considering the example of the latching feature in MEMS SAD, and comparing the results with experimental data obtained from a fabricated prototype. The proposed methodology accurately determines the failure probability and sensitive parameters of the sample, and provides insights into the impact of fabrication errors on the structural failure of the sample. It achieves the objective of reducing the burden of repetitive finite element analysis (FEA) in uncertainty analysis, and provides an efficient way to account for uncertainty in the study of MEMS devices.
- 13 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (14) , 15469-15478
Research on Structural Failure of MEMS Safety and Arming Device Considering Uncertainty in Fabrication Errors
This paper presents an efficient methodology for assessing the structural failure of microelectromechanical systems (MEMS) used in safety and arming devices (SAD) while taking into account the effect of fabrication errors. The proposed methodology uses statistical characteristics that are assessed using non-intrusive polynomial chaos expansion (PCE) to consider uncertainty. The effectiveness of the methodology is demonstrated by considering the example of the latching feature in MEMS SAD, and comparing the results with experimental data obtained from a fabricated prototype. The proposed methodology accurately determines the failure probability and sensitive parameters of the sample, and provides insights into the impact of fabrication errors on the structural failure of the sample. It achieves the objective of reducing the burden of repetitive finite element analysis (FEA) in uncertainty analysis, and provides an efficient way to account for uncertainty in the study of MEMS devices.