Jin Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jin Lu has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Jingjing Ji
State Key Laboratory of Intelligent Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Wuhan, China
3 shared publications - Jiafeng Zhu
State Key Laboratory of Intelligent Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Hubei, Wuhan, China
2 shared publications - Bangyan Niu
State Key Laboratory of Intelligent Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Wuhan, China
1 shared publication - Kok-Meng Lee
George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA, USA
1 shared publication - YongAn Huang
State Key Laboratory of Intelligent Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Wuhan, China
1 shared publication
Latest Publications
- 13 June 2025
- Published by Elsevier in Measurement
- Vol. 256
A compact in-situ shape sensing membrane integrating displacement reconstruction and sensor layout design algorithm
- 13 June 2025
- Published by Elsevier in Measurement
- Vol. 256
A compact in-situ shape sensing membrane integrating displacement reconstruction and sensor layout design algorithm
- 12 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-11
Full-Field Deformation Perception via Flexible Sensing Film Integrating Modified Inverse Finite Element Method
Full-field deformation can support the adjustment of morphing aircraft’ shape which has significant impacts on the aerodynamic performance. A deformation perception system (DPS) combining an intelligent flexible sensing film (iFlexSense) and a displacement reconstruction algorithm is proposed. The iFlexSense features ultra-thin, low elastic modulus, and geometric conformality. A strain observation has been realized simply by pasting the sensing film to the inner surface of the wing skin. A single-side inverse finite element method (ssiFEM), is proposed for displacement reconstruction from discrete strain observations on just one side of the target structural component, circumventing the requirement of precisely paired sensors in the vanilla iFEM. The full-field displacement is formulated as a closed-form solution combining an offline quasi-stiffness matrix and discrete strain observations. Hence a rapid estimation for the displacement is achieved. The ssiFEM has been validated in simulations on a platy cantilever. The relative error of ssiFEM reaches no more than 3.5% at the maximum deflection point under two typical cases, and after a data densification (DD) step, the mean absolute error averaged the whole cantilever can be reduced. The DD-enhanced ssiFEM has been employed with the prototyped iFlexSense for a practical deformation perception system of a morphing wing skin. The peak error of the perception system was less than 2mm out of a ±30mm deflection range. The application prospects of the system for perceiving smooth shapes can be envisioned.
- 12 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-11
Full-Field Deformation Perception via Flexible Sensing Film Integrating Modified Inverse Finite Element Method
Full-field deformation can support the adjustment of morphing aircraft’ shape which has significant impacts on the aerodynamic performance. A deformation perception system (DPS) combining an intelligent flexible sensing film (iFlexSense) and a displacement reconstruction algorithm is proposed. The iFlexSense features ultra-thin, low elastic modulus, and geometric conformality. A strain observation has been realized simply by pasting the sensing film to the inner surface of the wing skin. A single-side inverse finite element method (ssiFEM), is proposed for displacement reconstruction from discrete strain observations on just one side of the target structural component, circumventing the requirement of precisely paired sensors in the vanilla iFEM. The full-field displacement is formulated as a closed-form solution combining an offline quasi-stiffness matrix and discrete strain observations. Hence a rapid estimation for the displacement is achieved. The ssiFEM has been validated in simulations on a platy cantilever. The relative error of ssiFEM reaches no more than 3.5% at the maximum deflection point under two typical cases, and after a data densification (DD) step, the mean absolute error averaged the whole cantilever can be reduced. The DD-enhanced ssiFEM has been employed with the prototyped iFlexSense for a practical deformation perception system of a morphing wing skin. The peak error of the perception system was less than 2mm out of a ±30mm deflection range. The application prospects of the system for perceiving smooth shapes can be envisioned.
- 23 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 28 (3) , 1222-1233
Color Machine Vision Design Methodology of a Part-Presentation Algorithm for Automated Poultry Handling
This article offers an image processing method to optimize the design of a three-level color machine vision algorithm illustrated in the context of presenting a whole chicken carcass for subsequent handling, which overcomes some common problems in image segmentation, feature identification, and pose estimation for classifying, identifying, and locating poultry meat products. First, artificial color contrast and principal component analysis are optimized to enhance the contrast between similar colors to extract targeted regions more effectively. Second, the boundaries of poultry products are mostly smooth curves that are proposed as features for object recognition. Third, image feature points are found using template matching, from which the object (size, location, and pose) can be accurately determined. The algorithm simplifies the complex edges of a poultry product into a finite number of arc-centers, which greatly improves the efficiency/accuracy of the matching for part-presentation. Evaluated with 100 randomly posed samples, the algorithm has a success rate of 93%. The 7% failures were primarily due to missing points, which can be eliminated by incorporating more template points.
- 23 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 28 (3) , 1222-1233
Color Machine Vision Design Methodology of a Part-Presentation Algorithm for Automated Poultry Handling
This article offers an image processing method to optimize the design of a three-level color machine vision algorithm illustrated in the context of presenting a whole chicken carcass for subsequent handling, which overcomes some common problems in image segmentation, feature identification, and pose estimation for classifying, identifying, and locating poultry meat products. First, artificial color contrast and principal component analysis are optimized to enhance the contrast between similar colors to extract targeted regions more effectively. Second, the boundaries of poultry products are mostly smooth curves that are proposed as features for object recognition. Third, image feature points are found using template matching, from which the object (size, location, and pose) can be accurately determined. The algorithm simplifies the complex edges of a poultry product into a finite number of arc-centers, which greatly improves the efficiency/accuracy of the matching for part-presentation. Evaluated with 100 randomly posed samples, the algorithm has a success rate of 93%. The 7% failures were primarily due to missing points, which can be eliminated by incorporating more template points.