LZLaimis Zubauskas

Laimis Zubauskas

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Laimis Zubauskas has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Comparative analysis of microlens array formation in fused silica glass by laser: Femtosecond versus picosecond pulses

    by Laimis Zubauskas, Edgaras Markauskas, Arnas Vyšniauskas, Valdemar Stankevič, Paulius Gečys


  • Open Access

    GaAs ablation with ultrashort laser pulses in ambient air and water environments

    by Edgaras Markauskas, Laimis Zubauskas, Arnas Naujokaitis, Bronislovas Čechavičius, Martynas Talaikis, Gediminas Niaura, Mária Čaplovičová, Viliam Vretenár, Tadas Paulauskas

    Water-assisted ultrashort laser pulse processing of semiconductor materials is a promising technique to diminish heat accumulation and improve process quality. In this study, we investigate femtosecond laser ablation of deep trenches in GaAs, an important optoelectronic material, using water and ambient air environments at different laser processing regimes. We perform a comprehensive analysis of ablated trenches, including surface morphological analysis, atomic-resolution transmission electron microscopy imaging, elemental mapping, photoluminescence, and Raman spectroscopy. The findings demonstrate that GaAs ablation efficiency is enhanced in a water environment while heat-accumulation-related damage is reduced. Raman spectroscopy reveals a decrease in the broad feature associated with amorphous GaAs surface layers during water-assisted laser processing, suggesting that a higher material quality in deep trenches can be achieved using a water environment.


  • Open Access

    Femtosecond Laser Cutting of 110–550 µm Thickness Borosilicate Glass in Ambient Air and Water

    by Edgaras Markauskas, Laimis Zubauskas, Gediminas Račiukaitis, Paulius Gečys

    The cutting quality and strength of strips cut with femtosecond-duration pulses were investigated for different thicknesses of borosilicate glass plates. The laser pulse duration was 350 fs, and cutting was performed in two environments: ambient air and water. When cutting in water, a thin flowing layer of water was formed at the front surface of the glass plate by spraying water mist next to a laser ablation zone. The energy of pulses greatly exceeded the critical self-focusing threshold in water, creating conditions favorable for laser beam filament formation. Laser cutting parameters were individually optimized for different glass thicknesses (110–550 µm). The results revealed that laser cutting of borosilicate glass in water is favorable for thicker glass (300–550 µm) thanks to higher cutting quality, higher effective cutting speed, and characteristic strength. On the other hand, cutting ultrathin glass plates (110 µm thickness) demonstrated almost identical performance and cutting quality results in both environments. In this paper, we studied cut-edge defect widths, cut-sidewall roughness, cutting throughput, characteristic strength, and band-like damage formed at the back surface of laser-cut glass strips.


  • Open Access

    Efficient Water-Assisted Glass Cutting with 355 nm Picosecond Laser Pulses

    by Edgaras Markauskas, Laimis Zubauskas, Bogdan Voisiat, Paulius Gečys

    In this study, the cutting of borosilicate glass plates in ambient air and water with a 355 nm wavelength picosecond laser was carried out. Low (2.1–2.75 W) and high (15.5 W) average laser power cutting regimes were studied. Thorough attention was paid to the effect of the hatch distance on the cutting quality and characteristic strength of glass strips cut in both environments. At optimal cutting parameters, ablation efficiency and cutting rates were the highest but cut sidewalls were covered with periodically recurring ridges. Transition to smaller hatch values improved the cut sidewall quality by suppressing the ridge formation, but negatively affected the ablation efficiency and overall strength of glass strips. Glass strips cut in water in the low-laser-power regime had the highest characteristic strength of 117.6 and 107.3 MPa for the front and back sides, respectively. Cutting in a high-laser-power regime was only carried out in water. At 15.5 W, the ablation efficiency and effective cutting speed per incident laser power increased by 16% and 22%, respectively, compared with cutting in water in a low-laser-power regime.