Shihao Xin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shihao Xin has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Fangyu Peng
7 shared publications- Jiawei Wu
Huazhong University of Science and Technology School of Mechanical Science and Engineering Wuhan 430074 , China
7 shared publications Rong Yan
6 shared publications- Xiaowei Tang
School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
6 shared publications Xiaowei Tang
5 shared publications- Fangyu Peng
Huazhong University of Science and Technology
4 shared publications
Latest Publications
- Open Access
- 13 March 2024
- Published by Elsevier in Chinese Journal of Aeronautics
- Vol. 38 (3) , 102974
Low-frequency chatter suppression in robotic milling using Magnetorheological Joint Damper (MRJD)
- 13 March 2024
- Published by Elsevier in Chinese Journal of Aeronautics
- Vol. 38 (3) , 102974
Open AccessLow-frequency chatter suppression in robotic milling using Magnetorheological Joint Damper (MRJD)
- 11 September 2023
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 145 (11) , 1-25
An Incremental Self-Excitation Method for Effectively Identifying Low-Frequency Frequency Response Function of Milling Robots
Robotic machining efficiency and accuracy are constrained by milling vibrations and chatter. The dynamic characteristics of robots are highly influenced by their poses. Consequently, it is crucial to obtain the robot’s dynamic characteristics in any given pose to mitigate vibrations and prevent chatter during large-range machining. This paper proposes an incremental self-excitation method for effectively identifying low-frequency frequency response functions (FRF) of milling robots. By attaching a mass block at the robot’s end, a fully knowable and controllable excitation increment can be achieved, overcoming the shortcoming of traditional self-excitation methods in capturing the dynamic compliance magnitude. By employing suitable trajectory programming, this method can be executed automatically in the desired poses without the need for manual operations. First, the impulse (moment) of the incremental self-excitation is modeled based on momentum theorem, and the association model of the pulse response increment with the incremental self-excitation is established. To address the issue of sensitivity to noise in the FRF calculation process, the incremental self-excitation is assumed to be a Gaussian pulse, and its identification method is provided. Subsequently, the dimensionality requirement for identifying the nine-item (direct and cross) FRFs is effectively reduced using the modal directionality of milling robots, and the corresponding FRF calculation method is proposed. The rationality of the simplifications and assumptions employed in this method is validated through experiments and calculations. The experimental results in several robot poses show that the proposed method can effectively identify all the direct and cross FRFs in the low-frequency band.
- 11 September 2023
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 145 (11) , 1-25
An Incremental Self-Excitation Method for Effectively Identifying Low-Frequency Frequency Response Function of Milling Robots
Robotic machining efficiency and accuracy are constrained by milling vibrations and chatter. The dynamic characteristics of robots are highly influenced by their poses. Consequently, it is crucial to obtain the robot’s dynamic characteristics in any given pose to mitigate vibrations and prevent chatter during large-range machining. This paper proposes an incremental self-excitation method for effectively identifying low-frequency frequency response functions (FRF) of milling robots. By attaching a mass block at the robot’s end, a fully knowable and controllable excitation increment can be achieved, overcoming the shortcoming of traditional self-excitation methods in capturing the dynamic compliance magnitude. By employing suitable trajectory programming, this method can be executed automatically in the desired poses without the need for manual operations. First, the impulse (moment) of the incremental self-excitation is modeled based on momentum theorem, and the association model of the pulse response increment with the incremental self-excitation is established. To address the issue of sensitivity to noise in the FRF calculation process, the incremental self-excitation is assumed to be a Gaussian pulse, and its identification method is provided. Subsequently, the dimensionality requirement for identifying the nine-item (direct and cross) FRFs is effectively reduced using the modal directionality of milling robots, and the corresponding FRF calculation method is proposed. The rationality of the simplifications and assumptions employed in this method is validated through experiments and calculations. The experimental results in several robot poses show that the proposed method can effectively identify all the direct and cross FRFs in the low-frequency band.
- 16 June 2023
- Published by Elsevier in International Journal of Machine Tools and Manufacture
- Vol. 190
Investigation of the low-frequency chatter in robotic milling
- 16 June 2023
- Published by Elsevier in International Journal of Machine Tools and Manufacture
- Vol. 190
Investigation of the low-frequency chatter in robotic milling
- 23 August 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 122 (3-4) , 1431-1455
Chip wave phase difference analysis of robotic milling and chatter dominant mode research
- 23 August 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 122 (3-4) , 1431-1455
Chip wave phase difference analysis of robotic milling and chatter dominant mode research
- 29 March 2021
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 143 (8)
Analysis of the Effect of Tool Posture on Stability Considering the Nonlinear Dynamic Cutting Force Coefficient
In aviation and navigation, complicated parts are milled with high-speed low-feed-per-tooth milling to decrease tool vibration for high quality. Because the nonlinearity of the cutting force coefficient (CFC) is more evident with the relatively smaller instantaneous uncut chip thickness, the stable critical cutting depth and its distribution against different tool postures are affected. Considering the nonlinearity, a nonlinear dynamic CFC model that reveals the effect of the dynamic instantaneous uncut chip thickness on the dynamic cutting force is derived based on the Taylor expansion. A five-axis bull-nose end milling dynamics model is established with the nonlinear dynamic CFC model. The stable critical cutting depth distribution with respect to tool posture is analyzed. The stability results predicted with the dynamic CFC model are compared with those from the static CFC model and the constant CFC model. The effects of tool posture and feed per tooth on stable critical cutting depth were also analyzed, and the proposed model was validated by cutting experiments. The maximal stable critical cutting depths that can be achieved under different tool postures by feed per tooth adjustment were calculated, and corresponding distribution diagrams are proposed for milling parameter optimization.
- 29 March 2021
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 143 (8)
Analysis of the Effect of Tool Posture on Stability Considering the Nonlinear Dynamic Cutting Force Coefficient
In aviation and navigation, complicated parts are milled with high-speed low-feed-per-tooth milling to decrease tool vibration for high quality. Because the nonlinearity of the cutting force coefficient (CFC) is more evident with the relatively smaller instantaneous uncut chip thickness, the stable critical cutting depth and its distribution against different tool postures are affected. Considering the nonlinearity, a nonlinear dynamic CFC model that reveals the effect of the dynamic instantaneous uncut chip thickness on the dynamic cutting force is derived based on the Taylor expansion. A five-axis bull-nose end milling dynamics model is established with the nonlinear dynamic CFC model. The stable critical cutting depth distribution with respect to tool posture is analyzed. The stability results predicted with the dynamic CFC model are compared with those from the static CFC model and the constant CFC model. The effects of tool posture and feed per tooth on stable critical cutting depth were also analyzed, and the proposed model was validated by cutting experiments. The maximal stable critical cutting depths that can be achieved under different tool postures by feed per tooth adjustment were calculated, and corresponding distribution diagrams are proposed for milling parameter optimization.