Min Xie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Min Xie has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Rende Mu
AECC Beijing Institute of Aeronautical Materials, Beijing 100095, China
3 shared publications - Xiwen Song
School of Materials Science and Engineering, Inner Mongolia University of Science and Technology, Baotou 014010, China
3 shared publications - Yonghe Zhang
School of Materials Science and Engineering, Inner Mongolia University of Science and Technology, Baotou 014010, China
3 shared publications - Zhi-Gang Wang
School of Materials Science and Engineering, Inner Mongolia University of Science and Technology, Baotou 014010, China
3 shared publications - Bianlei Hao
School of Materials Science and Engineering, Inner Mongolia University of Science and Technology, Baotou 014010, China
1 shared publication - Chenxi Xia
School of Materials Science and Engineering, Inner Mongolia University of Science and Technology, Baotou 014010, China
1 shared publication
Latest Publications
- Open Access
Effect of Molten-Salt Chemistry on Phase Evolution and Corrosion Degradation of Sc2O3-Y2O3 Co-Stabilized ZrO2 Thermal Barrier Ceramics
The corrosion resistance of electron-beam physical vapor-deposited (EB-PVD) zirconia thermal-barrier coatings depends on ceramic phase stability. Here, conventional 8YSZ and two Sc2O3-Y2O3 co-stabilized ZrO2 coatings, ScYSZ and ScYSZ with an Al-rich interlayer (ScYSZA), were comparatively investigated under three chloride-containing environments: NaCl (N) corrosion, high-temperature Na2SO4-NaCl (NN) corrosion, and Na2SO4-NaCl-V2O5 (NNV) corrosion. Phase evolution and microstructural degradation were examined by X-ray diffraction, Raman spectroscopy, scanning electron microscopy, and energy-dispersive spectroscopy. Under N exposure, the ceramic top coats largely retained the tetragonal t′-ZrO2 phase, whereas degradation was concentrated near the ceramic/bond-coat interface. NN corrosion caused limited bulk phase transformation. The most pronounced degradation occurred under NNV exposure, particularly in 8YSZ, where extensive YVO4 formation and progressive t′→m transformation were accompanied by substantial disruption of the columnar ceramic structure. After 100 h of NNV corrosion, 8YSZ contained only 23.7 wt.% t′-ZrO2. In contrast, ScYSZ and ScYSZA retained 82.6 and 84.4 wt.% t′-ZrO2, respectively, confirming the superior phase stability and corrosion resistance of the ScYSZ-based coatings, particularly ScYSZA. These results demonstrate that chloride-containing environments produce distinct degradation pathways involving interfacial oxidation, corrosive-species ingress, and phase destabilization, highlighting the importance of integrating ceramic composition with coating architecture to improve the durability of EB-PVD thermal-barrier coatings.
Open AccessEffect of Molten-Salt Chemistry on Phase Evolution and Corrosion Degradation of Sc2O3-Y2O3 Co-Stabilized ZrO2 Thermal Barrier Ceramics
The corrosion resistance of electron-beam physical vapor-deposited (EB-PVD) zirconia thermal-barrier coatings depends on ceramic phase stability. Here, conventional 8YSZ and two Sc2O3-Y2O3 co-stabilized ZrO2 coatings, ScYSZ and ScYSZ with an Al-rich interlayer (ScYSZA), were comparatively investigated under three chloride-containing environments: NaCl (N) corrosion, high-temperature Na2SO4-NaCl (NN) corrosion, and Na2SO4-NaCl-V2O5 (NNV) corrosion. Phase evolution and microstructural degradation were examined by X-ray diffraction, Raman spectroscopy, scanning electron microscopy, and energy-dispersive spectroscopy. Under N exposure, the ceramic top coats largely retained the tetragonal t′-ZrO2 phase, whereas degradation was concentrated near the ceramic/bond-coat interface. NN corrosion caused limited bulk phase transformation. The most pronounced degradation occurred under NNV exposure, particularly in 8YSZ, where extensive YVO4 formation and progressive t′→m transformation were accompanied by substantial disruption of the columnar ceramic structure. After 100 h of NNV corrosion, 8YSZ contained only 23.7 wt.% t′-ZrO2. In contrast, ScYSZ and ScYSZA retained 82.6 and 84.4 wt.% t′-ZrO2, respectively, confirming the superior phase stability and corrosion resistance of the ScYSZ-based coatings, particularly ScYSZA. These results demonstrate that chloride-containing environments produce distinct degradation pathways involving interfacial oxidation, corrosive-species ingress, and phase destabilization, highlighting the importance of integrating ceramic composition with coating architecture to improve the durability of EB-PVD thermal-barrier coatings.
- Open Access
Thermophysical–Infrared Emission Synergistic Optimization Mechanism of Sc2O3–CeO2 Co-Doped YSZ Ceramics
Conventional 8YSZ thermal barrier ceramics suffer from limited phase stability and insufficient infrared radiation regulation at high temperatures. Sc2O3 doping can reduce thermal conductivity and improve phase stability, but the improvement remains limited because the fixed-valence substitution of Sc3+ cannot effectively increase defect concentration or regulate carrier behavior. In this work, CeO2 with tunable valence states was incorporated into the Sc-stabilized YSZ system to realize the synergistic modulation of lattice thermal conductivity and photon thermal conductivity. A series of Sc2O3–CeO2 co-doped YSZ ceramics were fabricated via solid-state sintering, and the effects of co-doping on phase structure, defect evolution, thermal conductivity, infrared emissivity, and bandgap characteristics were systematically investigated. The results show that all co-doped samples maintained a stable tetragonal fluorite structure with relative densities higher than 96%. Among them, Sc0.08Ce0.005Y0.005Zr0.91O2 exhibited the best comprehensive performance. Its thermal conductivity at 1000 °C reached 2.073 W·m−1·K−1, which was 11.9% lower than that of conventional 8YSZ. Meanwhile, the average infrared emissivity in the 3–5 μm band increased to 0.779. XPS analysis indicated that Ce incorporation promoted oxygen-vacancy formation, which enhanced phonon scattering and reduced lattice thermal conductivity. In addition, co-doping narrowed the band gap and facilitated carrier excitation, thereby strengthening infrared absorption and emission behavior. The enhanced infrared emissivity further contributed to the suppression of radiative thermal transport at elevated temperatures. This work demonstrates that Sc2O3–CeO2 co-doping provides an effective strategy for simultaneously regulating phonon transport and photon transport in YSZ-based ceramics. The results provide new insight into the design of advanced thermal barrier materials with low thermal conductivity and enhanced high-temperature infrared radiation performance.
Open AccessThermophysical–Infrared Emission Synergistic Optimization Mechanism of Sc2O3–CeO2 Co-Doped YSZ Ceramics
Conventional 8YSZ thermal barrier ceramics suffer from limited phase stability and insufficient infrared radiation regulation at high temperatures. Sc2O3 doping can reduce thermal conductivity and improve phase stability, but the improvement remains limited because the fixed-valence substitution of Sc3+ cannot effectively increase defect concentration or regulate carrier behavior. In this work, CeO2 with tunable valence states was incorporated into the Sc-stabilized YSZ system to realize the synergistic modulation of lattice thermal conductivity and photon thermal conductivity. A series of Sc2O3–CeO2 co-doped YSZ ceramics were fabricated via solid-state sintering, and the effects of co-doping on phase structure, defect evolution, thermal conductivity, infrared emissivity, and bandgap characteristics were systematically investigated. The results show that all co-doped samples maintained a stable tetragonal fluorite structure with relative densities higher than 96%. Among them, Sc0.08Ce0.005Y0.005Zr0.91O2 exhibited the best comprehensive performance. Its thermal conductivity at 1000 °C reached 2.073 W·m−1·K−1, which was 11.9% lower than that of conventional 8YSZ. Meanwhile, the average infrared emissivity in the 3–5 μm band increased to 0.779. XPS analysis indicated that Ce incorporation promoted oxygen-vacancy formation, which enhanced phonon scattering and reduced lattice thermal conductivity. In addition, co-doping narrowed the band gap and facilitated carrier excitation, thereby strengthening infrared absorption and emission behavior. The enhanced infrared emissivity further contributed to the suppression of radiative thermal transport at elevated temperatures. This work demonstrates that Sc2O3–CeO2 co-doping provides an effective strategy for simultaneously regulating phonon transport and photon transport in YSZ-based ceramics. The results provide new insight into the design of advanced thermal barrier materials with low thermal conductivity and enhanced high-temperature infrared radiation performance.
- Open Access
Study of Gd2O3-Doped La2(Zr0.7Ce0.3)2O7 Thermal Barriers for Coating Ceramic Materials for CMAS Resistance
The stability of thermal barrier coating (TBC) materials during service is a prerequisite for the normal operation of aircraft engines. The high-temperature corrosion of CaO–MgO–Al2O3–SiO2 (CMAS) is an important factor that affects the stability of TBCs on turbine blades and causes premature engine failure. For traditional 6-8 YSZ, at temperatures of more than 1200 °C, the thermal insulation performance is significantly reduced, which makes it necessary to find new, alternative materials. La2Zr2O7 has good thermal physical properties; the addition of Ce4+ improves its mechanical properties, while adding Gd2O3 affects its corrosion resistance. Herein, high-temperature corrosion studies of (La1−xGdx)2(Zr0.7Ce0.3)2O7 (L-GZC) (x = 0, 0.3, 0.5, 0.7) ceramic TBC were conducted using CMAS glass at 1250 °C. The results indicate that CMAS rapidly dissolves L-GZC and separates the (La, Gd)8Ca2(SiO4)6O2 apatite phase, ZrO2, and other crystalline phases. These products form a crystalline layer at the contact boundary, which can inhibit further CMAS reactions. Among the coatings examined, the L-GZC ceramic (x = 0.7) exhibits better corrosion resistance, and the penetration depth is <200 μm after high-temperature corrosion at 1250 °C for 5, 10, and 20 h. The failure mechanism and potential risk of CMAS were also analyzed and discussed. The L-GZC ceramic material has good thermal corrosion resistance and is expected to replace the traditional YSZ to better meet the high-temperature working requirements of gas turbines and aircraft engines.
Open AccessStudy of Gd2O3-Doped La2(Zr0.7Ce0.3)2O7 Thermal Barriers for Coating Ceramic Materials for CMAS Resistance
The stability of thermal barrier coating (TBC) materials during service is a prerequisite for the normal operation of aircraft engines. The high-temperature corrosion of CaO–MgO–Al2O3–SiO2 (CMAS) is an important factor that affects the stability of TBCs on turbine blades and causes premature engine failure. For traditional 6-8 YSZ, at temperatures of more than 1200 °C, the thermal insulation performance is significantly reduced, which makes it necessary to find new, alternative materials. La2Zr2O7 has good thermal physical properties; the addition of Ce4+ improves its mechanical properties, while adding Gd2O3 affects its corrosion resistance. Herein, high-temperature corrosion studies of (La1−xGdx)2(Zr0.7Ce0.3)2O7 (L-GZC) (x = 0, 0.3, 0.5, 0.7) ceramic TBC were conducted using CMAS glass at 1250 °C. The results indicate that CMAS rapidly dissolves L-GZC and separates the (La, Gd)8Ca2(SiO4)6O2 apatite phase, ZrO2, and other crystalline phases. These products form a crystalline layer at the contact boundary, which can inhibit further CMAS reactions. Among the coatings examined, the L-GZC ceramic (x = 0.7) exhibits better corrosion resistance, and the penetration depth is <200 μm after high-temperature corrosion at 1250 °C for 5, 10, and 20 h. The failure mechanism and potential risk of CMAS were also analyzed and discussed. The L-GZC ceramic material has good thermal corrosion resistance and is expected to replace the traditional YSZ to better meet the high-temperature working requirements of gas turbines and aircraft engines.
- Open Access
Nanocrystalline Alumina-Zirconia-Based Eutectic Ceramics Fabricated with High-Energy Beams: Principle, Solidification Techniques, Microstructure and Mechanical Properties
Nanocrystalline alumina-zirconia-based eutectic ceramics fabricated with high-energy beams and composed of ultrafine, three-dimensionally entangled, single-crystal domains are a special category of eutectic oxides that exhibit exceptionally high-temperature mechanical properties, such as strength and toughness as well as creep resistance. This paper aims to provide a comprehensive review on the basic principles, advanced solidification processes, microstructure and mechanical properties of alumina-zirconia-based eutectic ceramics, with particular attention to the status of the art on a nanocrystalline scale. Some basic principles of coupled eutectic growth are first introduced based on previously reported models, followed by concise introduction of solidification techniques and the control strategy of solidification behavior from the processing variables. Then, the microstructural formation of nanoeutectic structure is elucidated with regard to different hierarchical scales, and mechanical properties such as hardness, flexural and tensile strength, fracture toughness and wear resistance are discussed in detail for a comparative study. Nanocrystalline alumina-zirconia-based eutectic ceramics with unique microstructural and compositional characteristics have been produced with high-energy beam-based processes, and in many cases, promising improvements in mechanical performance have been reported as contrasting with conventional eutectic ceramics.
Open AccessNanocrystalline Alumina-Zirconia-Based Eutectic Ceramics Fabricated with High-Energy Beams: Principle, Solidification Techniques, Microstructure and Mechanical Properties
Nanocrystalline alumina-zirconia-based eutectic ceramics fabricated with high-energy beams and composed of ultrafine, three-dimensionally entangled, single-crystal domains are a special category of eutectic oxides that exhibit exceptionally high-temperature mechanical properties, such as strength and toughness as well as creep resistance. This paper aims to provide a comprehensive review on the basic principles, advanced solidification processes, microstructure and mechanical properties of alumina-zirconia-based eutectic ceramics, with particular attention to the status of the art on a nanocrystalline scale. Some basic principles of coupled eutectic growth are first introduced based on previously reported models, followed by concise introduction of solidification techniques and the control strategy of solidification behavior from the processing variables. Then, the microstructural formation of nanoeutectic structure is elucidated with regard to different hierarchical scales, and mechanical properties such as hardness, flexural and tensile strength, fracture toughness and wear resistance are discussed in detail for a comparative study. Nanocrystalline alumina-zirconia-based eutectic ceramics with unique microstructural and compositional characteristics have been produced with high-energy beam-based processes, and in many cases, promising improvements in mechanical performance have been reported as contrasting with conventional eutectic ceramics.