Mustafa Taha Aslan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mustafa Taha Aslan has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Erol İskender
Department of Civil Engineering, Faculty of Technology, Karadeniz Technical University, Trabzon 61830, Türkiye
7 shared publications - Atakan Aksoy
Karadeniz Technical University
5 shared publications Ataturk University
1 shared publication- Canan Aksoy
Karadeniz Teknik Üniversitesi
1 shared publication - Cansu İskender
Avrasya University
1 shared publication - Celaleddin Ensar Şengül
DEVLET SU İŞLERİ GENEL MÜDÜRLÜĞÜ
1 shared publication
Latest Publications
- Open Access
Physicochemical Characterization, Binder Rheology, and Engineering Performance of Diatomite–Microfiber Hybrid Asphalt Systems
Diatomite and microfibers have been investigated as asphalt modifiers, but limited attention has been given to how differences between diatomite sources and microfiber formulations are reflected across binder- and mixture-scale performance. This study investigated two diatomites (D1 and D2) and three microfibers—polyacrylonitrile (PAN), polyethylene terephthalate (PET), and basalt—using a multiscale experimental approach. The diatomites were characterized by particle-size analysis, SEM–EDS, XRF, and XRD, while the fibers were examined using SEM–EDS, XRD, and binder-retention testing. Diatomite-modified binders containing 10% and 15% modifier were evaluated for conventional, rheological, and aging properties. At the mixture scale, selected 15%D1 and 10%D2 systems were combined with the three fibers and compared with unmodified and 5% SBS-modified references. D1 was finer and had a slightly higher SiO2 content than D2, while both showed silica-rich porous structures. Diatomite generally increased binder consistency and viscosity and improved the high-temperature rheological response without changing the BBR critical temperature. The 10%D2-PAN mixture achieved the highest indirect tensile strength (4.29 MPa), while the tensile strength ratios of 10%D2-PAN and 10%D2-PET were 82–83%. The 10%D2 formulations showed Cantabro losses of 5.5–6.7% and permanent deformations of 0.247–0.255 mm. In the adapted 100 mm SCB test, 10%D2-PAN also produced the highest flexibility index (10.6) and fracture energy (7.3 kJ/m2). Overall, the results indicate that diatomite source characteristics and microfiber formulation should be considered together, with 10%D2-PAN exhibiting a favorable combination of strength, moisture-resistance, particle-loss, permanent-deformation, and fracture-related responses under the investigated conditions.
Open AccessPhysicochemical Characterization, Binder Rheology, and Engineering Performance of Diatomite–Microfiber Hybrid Asphalt Systems
Diatomite and microfibers have been investigated as asphalt modifiers, but limited attention has been given to how differences between diatomite sources and microfiber formulations are reflected across binder- and mixture-scale performance. This study investigated two diatomites (D1 and D2) and three microfibers—polyacrylonitrile (PAN), polyethylene terephthalate (PET), and basalt—using a multiscale experimental approach. The diatomites were characterized by particle-size analysis, SEM–EDS, XRF, and XRD, while the fibers were examined using SEM–EDS, XRD, and binder-retention testing. Diatomite-modified binders containing 10% and 15% modifier were evaluated for conventional, rheological, and aging properties. At the mixture scale, selected 15%D1 and 10%D2 systems were combined with the three fibers and compared with unmodified and 5% SBS-modified references. D1 was finer and had a slightly higher SiO2 content than D2, while both showed silica-rich porous structures. Diatomite generally increased binder consistency and viscosity and improved the high-temperature rheological response without changing the BBR critical temperature. The 10%D2-PAN mixture achieved the highest indirect tensile strength (4.29 MPa), while the tensile strength ratios of 10%D2-PAN and 10%D2-PET were 82–83%. The 10%D2 formulations showed Cantabro losses of 5.5–6.7% and permanent deformations of 0.247–0.255 mm. In the adapted 100 mm SCB test, 10%D2-PAN also produced the highest flexibility index (10.6) and fracture energy (7.3 kJ/m2). Overall, the results indicate that diatomite source characteristics and microfiber formulation should be considered together, with 10%D2-PAN exhibiting a favorable combination of strength, moisture-resistance, particle-loss, permanent-deformation, and fracture-related responses under the investigated conditions.
- Open Access
Performance of Asphalt Mixtures Hybrid-Modified with Industrial Diatomite By-Products and Different Microfibres
This study evaluated asphalt mixtures incorporating two diatomite types (D1 and D2) at contents of 10% and 15% by binder weight and three fibre treatments added by aggregate weight: polyacrylonitrile (PAN) (0.065%), polyethylene terephthalate (PET) (0.10%), and basalt fibre (0.30%). An unmodified mixture and a mixture containing 5% styrene–butadiene–styrene (SBS) by binder weight were included as references. Performance was assessed using indirect tensile strength (ITS), tensile strength ratio (TSR), Cantabro loss, repeated load creep, and semi-circular bending (SCB) tests. Factorial analysis of variance indicated that diatomite type and content significantly affected ITS, diatomite content governed permanent deformation, and diatomite type was the principal factor affecting Cantabro loss. Significant interaction effects for the SCB parameters showed that fracture performance depended on the specific combination of diatomite and fibre treatments. Among the tested formulations, D1%10-PAN exhibited the highest ITS of 4712.36 kPa, representing numerical increases of 43.8% and 22.4% over the control and SBS-modified mixtures, respectively. D1%10-PET achieved the highest TSR (95.58%), whereas D2%10-PAN exhibited the lowest Cantabro loss (6.76%). Mixtures containing 15% diatomite generally showed lower permanent deformation, while D2%10-PAN achieved the highest flexibility index (14.003). The different performance trends observed for D1 and D2 are likely associated with differences in their physical characteristics, such as particle morphology and binder absorption behaviour, which may influence their interaction with the asphalt mastic and fibre reinforcement. No single formulation provided the best performance for every response. Overall, D2-based treatments improved resistance to particle loss, a higher diatomite content enhanced permanent deformation resistance, and 10% diatomite combined with PAN or PET treatment provided a more favourable balance of tensile, moisture, and fracture performance.
Open AccessPerformance of Asphalt Mixtures Hybrid-Modified with Industrial Diatomite By-Products and Different Microfibres
This study evaluated asphalt mixtures incorporating two diatomite types (D1 and D2) at contents of 10% and 15% by binder weight and three fibre treatments added by aggregate weight: polyacrylonitrile (PAN) (0.065%), polyethylene terephthalate (PET) (0.10%), and basalt fibre (0.30%). An unmodified mixture and a mixture containing 5% styrene–butadiene–styrene (SBS) by binder weight were included as references. Performance was assessed using indirect tensile strength (ITS), tensile strength ratio (TSR), Cantabro loss, repeated load creep, and semi-circular bending (SCB) tests. Factorial analysis of variance indicated that diatomite type and content significantly affected ITS, diatomite content governed permanent deformation, and diatomite type was the principal factor affecting Cantabro loss. Significant interaction effects for the SCB parameters showed that fracture performance depended on the specific combination of diatomite and fibre treatments. Among the tested formulations, D1%10-PAN exhibited the highest ITS of 4712.36 kPa, representing numerical increases of 43.8% and 22.4% over the control and SBS-modified mixtures, respectively. D1%10-PET achieved the highest TSR (95.58%), whereas D2%10-PAN exhibited the lowest Cantabro loss (6.76%). Mixtures containing 15% diatomite generally showed lower permanent deformation, while D2%10-PAN achieved the highest flexibility index (14.003). The different performance trends observed for D1 and D2 are likely associated with differences in their physical characteristics, such as particle morphology and binder absorption behaviour, which may influence their interaction with the asphalt mastic and fibre reinforcement. No single formulation provided the best performance for every response. Overall, D2-based treatments improved resistance to particle loss, a higher diatomite content enhanced permanent deformation resistance, and 10% diatomite combined with PAN or PET treatment provided a more favourable balance of tensile, moisture, and fracture performance.
- 9 March 2026
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 114 (6) , 475-485
Impact of polymer, nanomaterial, and rubber modification on the radioactivity and radiation shielding performance of bitumen
Natural radiation levels of bitumen are vital in understanding the potential health risks associated with exposure. The presence of radioactive elements in bitumens can impact environmental and human health. For this reason, in the current study, the natural radiation levels ( 238 U, 232 Th and 40 K radionuclides) of bitumen samples used in various modified materials were determined. It has been determined that the available samples do not carry any risk to human health in terms of radioactivity. Besides, polymer modified bitumen (PMB) has shown promise as a potential radiation shielding material due to its inherent properties and the flexibility it offers in engineering applications. Therefore, if the modified bitumens are to be used as a shielding material, it is necessary to determine their radiation shielding properties such as linear attenuation coefficients (LAC), mass attenuation coefficients (MAC), half value layer (HVL) and tenth value layer (TVL). In the present study, these values were calculated using 241 Am gamma ray source in a radiation absorption experimental setup. It was found that the samples have shown good shielding properties for low-energy gamma radiation.
- 9 March 2026
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 114 (6) , 475-485
Impact of polymer, nanomaterial, and rubber modification on the radioactivity and radiation shielding performance of bitumen
Natural radiation levels of bitumen are vital in understanding the potential health risks associated with exposure. The presence of radioactive elements in bitumens can impact environmental and human health. For this reason, in the current study, the natural radiation levels ( 238 U, 232 Th and 40 K radionuclides) of bitumen samples used in various modified materials were determined. It has been determined that the available samples do not carry any risk to human health in terms of radioactivity. Besides, polymer modified bitumen (PMB) has shown promise as a potential radiation shielding material due to its inherent properties and the flexibility it offers in engineering applications. Therefore, if the modified bitumens are to be used as a shielding material, it is necessary to determine their radiation shielding properties such as linear attenuation coefficients (LAC), mass attenuation coefficients (MAC), half value layer (HVL) and tenth value layer (TVL). In the present study, these values were calculated using 241 Am gamma ray source in a radiation absorption experimental setup. It was found that the samples have shown good shielding properties for low-energy gamma radiation.
- Open Access
- 1 November 2024
- Published by Teknik Dergi in Turkish Journal of Civil Engineering
- Vol. 35 (6) , 107-137
Performance Investigation of Diatomite Modified Asphalt Mixtures for Different Diatomite Ratios and Grinding Sizes
Modification of asphalt mixtures has become almost mandatory today due to increased stresses in pavements, shortening of load cycle times, and decreases in binder quality. For this reason, many additives can be added to bitumen or asphalt mixture. Industrial material wastes can also be among these additives. When diatomite material is used as a performance enhancer in asphalt mixtures, it significantly improves the main performance indicators of the asphalt mixture. However, low temperature cracking of diatomite-modified asphalt mixtures is still controversial in the literature. This study evaluated the asphalt mixture in terms of low-temperature cracking, water damage, and rutting, depending on the diatomite grinding size (gradation) and addition ratio. Three different sizes of diatomite additives (106, 212 and 300-micron maximum diameter) were used at three addition ratios (5, 10 and 15% by weight of bitumen). According to the test results, it was seen that the mechanical properties of asphalt mixtures were significantly affected by the addition ratios and diatomite sizes, and the use of 300-micron maximum diameter diatomite at the rate of 10% and 15% was more effective. However, according to the BBR test results, the use of diatomite additives with a maximum size of 106 µm at 5% slightly increased the low temperature cracking resistance.
- 1 November 2024
- Published by Teknik Dergi in Turkish Journal of Civil Engineering
- Vol. 35 (6) , 107-137
Open AccessPerformance Investigation of Diatomite Modified Asphalt Mixtures for Different Diatomite Ratios and Grinding Sizes
Modification of asphalt mixtures has become almost mandatory today due to increased stresses in pavements, shortening of load cycle times, and decreases in binder quality. For this reason, many additives can be added to bitumen or asphalt mixture. Industrial material wastes can also be among these additives. When diatomite material is used as a performance enhancer in asphalt mixtures, it significantly improves the main performance indicators of the asphalt mixture. However, low temperature cracking of diatomite-modified asphalt mixtures is still controversial in the literature. This study evaluated the asphalt mixture in terms of low-temperature cracking, water damage, and rutting, depending on the diatomite grinding size (gradation) and addition ratio. Three different sizes of diatomite additives (106, 212 and 300-micron maximum diameter) were used at three addition ratios (5, 10 and 15% by weight of bitumen). According to the test results, it was seen that the mechanical properties of asphalt mixtures were significantly affected by the addition ratios and diatomite sizes, and the use of 300-micron maximum diameter diatomite at the rate of 10% and 15% was more effective. However, according to the BBR test results, the use of diatomite additives with a maximum size of 106 µm at 5% slightly increased the low temperature cracking resistance.
- 31 March 2024
- Published by Golden Light Publishing in Journal of Construction Engineering, Management & Innovation
- Vol. 7 (1) , 34-55
Disaster waste management process: The case of February 6 earthquake
- 31 March 2024
- Published by Golden Light Publishing in Journal of Construction Engineering, Management & Innovation
- Vol. 7 (1) , 34-55
Disaster waste management process: The case of February 6 earthquake
- 5 March 2024
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 18 (5) , 1314-1326
A Method for Conditioning the Asphalt Mixtures
- 5 March 2024
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 18 (5) , 1314-1326
A Method for Conditioning the Asphalt Mixtures
- 16 December 2023
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 31 (3) , 893-904
FARKLI DİATOMİT İÇERİĞİ İÇİN ASFALT KAPLAMA PERFORMANSININ DEĞERLENDİRİLMESİ
The majority of steel and reinforced concrete bridges are produced with asphalt pavement. The reason for this is to protect steel and concrete structures from the effects of water and degrading salt additives and to increase their durability. Asphalt bridge superstructures are mostly manufactured with four layers. These layers are the primer bonding layer, waterproofing layer, protection layer and surface asphalt wearing layers. The superstructure must protect the supporting substructure. It should protect the life of the structure and ensure the integrity of the structure against permanent deformation, aging, raveling, water damage and chemical effects. Diatomite additive is used as a performance enhancer in various aspects. It is generally preferred in the region of 5%-15% according to the bitumen mass. The granulometric size and chemical properties of the diatomite additive are other effective factors. In this study, the rutting resistance of conventional and diatomite-modified asphalt pavement for 5% and 10% ratios for selected diatomite additive gradation is investigated. The rutting resistance of the pavements is investigated by repeated creep tests for two different additive ratios on water-damaged and control mixtures. In unconditioned samples, 5% diatomite-modified mixtures; in conditioned samples, 10% diatomite-modified mixtures showed the greatest deformation resistance.
- 16 December 2023
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 31 (3) , 893-904
FARKLI DİATOMİT İÇERİĞİ İÇİN ASFALT KAPLAMA PERFORMANSININ DEĞERLENDİRİLMESİ
The majority of steel and reinforced concrete bridges are produced with asphalt pavement. The reason for this is to protect steel and concrete structures from the effects of water and degrading salt additives and to increase their durability. Asphalt bridge superstructures are mostly manufactured with four layers. These layers are the primer bonding layer, waterproofing layer, protection layer and surface asphalt wearing layers. The superstructure must protect the supporting substructure. It should protect the life of the structure and ensure the integrity of the structure against permanent deformation, aging, raveling, water damage and chemical effects. Diatomite additive is used as a performance enhancer in various aspects. It is generally preferred in the region of 5%-15% according to the bitumen mass. The granulometric size and chemical properties of the diatomite additive are other effective factors. In this study, the rutting resistance of conventional and diatomite-modified asphalt pavement for 5% and 10% ratios for selected diatomite additive gradation is investigated. The rutting resistance of the pavements is investigated by repeated creep tests for two different additive ratios on water-damaged and control mixtures. In unconditioned samples, 5% diatomite-modified mixtures; in conditioned samples, 10% diatomite-modified mixtures showed the greatest deformation resistance.
- 30 June 2023
- Published by Recep Tayyip Erdogan Universitesi in Recep Tayyip Erdoğan Üniversitesi Fen ve Mühendislik Bilimleri Dergisi
- Vol. 4 (1) , 39-50
Asfalt Kaplamalarda Bitüm Oranına Bağlı Olarak Sıkıştırma Sıcaklığının Etkisinin Marshall Deneyi Parametreleri ile İncelenmesi
Asfalt kaplamaların sıkıştırma sıcaklığının kontrol altına alınması kaplamadan beklenen performansın sağlanması açısından en önemli konulardan birisidir. Tasarım ve üretim aşamalarında ne kadar dikkat edilse de serme ve sıkıştırma aşamalarında karışım sıcaklığında bir miktar homojensizlikler ortaya çıkabilmektedir. Bu çalışmada aşınma tabakası tip 1A’ya göre dizayn edilmiş yoğun gradasyonlu asfalt kaplamalar için optimum bitüm içeriği %5,1 olarak hesaplanmış, bu değerinin altında ve üstünde (4,8; 4,9; 5,0; 5,0; 5,2; 5,3; 5,4) bitüm oranlarında hazırlanan asfalt karışımlar 143 °C ve 137 °C sıkıştırma sıcaklığında imal edilmiştir. Asfalt karışım örnekleri pratik yoğunluk, akma, stabilite ve Marshall oranı parametreleri ile değerlendirilmiştir. Çalışma sonucunda, 143 °C sıkıştırma sıcaklığında 137 °C’ye göre daha yüksek Marshall stabilite değerlerinin elde edilebildiği, optimum bitüm oranından daha yüksek artan değerlerde bitüm oranının artmasıyla akma değerlerinin artmakta olduğu ve 143 °C sıkıştırma sıcaklığında 137 °C değerine göre daha düşük akma değerleri oluştuğu gözlemlenmiştir. Stabilite değerlerindeki standart hatanın 143 °C sıcaklıkta daha düşük olduğu, sıkıştırma işlemi yapılırken, homojenlik anlamında, düşük sıcaklıklarda daha çok dikkat edilmesi gerektiği anlaşılmıştır.
- 30 June 2023
- Published by Recep Tayyip Erdogan Universitesi in Recep Tayyip Erdoğan Üniversitesi Fen ve Mühendislik Bilimleri Dergisi
- Vol. 4 (1) , 39-50
Asfalt Kaplamalarda Bitüm Oranına Bağlı Olarak Sıkıştırma Sıcaklığının Etkisinin Marshall Deneyi Parametreleri ile İncelenmesi
Asfalt kaplamaların sıkıştırma sıcaklığının kontrol altına alınması kaplamadan beklenen performansın sağlanması açısından en önemli konulardan birisidir. Tasarım ve üretim aşamalarında ne kadar dikkat edilse de serme ve sıkıştırma aşamalarında karışım sıcaklığında bir miktar homojensizlikler ortaya çıkabilmektedir. Bu çalışmada aşınma tabakası tip 1A’ya göre dizayn edilmiş yoğun gradasyonlu asfalt kaplamalar için optimum bitüm içeriği %5,1 olarak hesaplanmış, bu değerinin altında ve üstünde (4,8; 4,9; 5,0; 5,0; 5,2; 5,3; 5,4) bitüm oranlarında hazırlanan asfalt karışımlar 143 °C ve 137 °C sıkıştırma sıcaklığında imal edilmiştir. Asfalt karışım örnekleri pratik yoğunluk, akma, stabilite ve Marshall oranı parametreleri ile değerlendirilmiştir. Çalışma sonucunda, 143 °C sıkıştırma sıcaklığında 137 °C’ye göre daha yüksek Marshall stabilite değerlerinin elde edilebildiği, optimum bitüm oranından daha yüksek artan değerlerde bitüm oranının artmasıyla akma değerlerinin artmakta olduğu ve 143 °C sıkıştırma sıcaklığında 137 °C değerine göre daha düşük akma değerleri oluştuğu gözlemlenmiştir. Stabilite değerlerindeki standart hatanın 143 °C sıcaklıkta daha düşük olduğu, sıkıştırma işlemi yapılırken, homojenlik anlamında, düşük sıcaklıklarda daha çok dikkat edilmesi gerektiği anlaşılmıştır.