Hans Joakim Skadsem
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hans Joakim Skadsem has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Knut Erik Teigen Giljarhus
Department of Mechanical and Structural Engineering and Materials Science, University of Stavanger, Stavanger, Norway
3 shared publications - Maryam Ghorbani
University of Stavanger
2 shared publications - Victor Nogueira Lima
Department of Energy and Petroleum Engineering, University of Stavanger, Stavanger, Norway
2 shared publications - Amir Taheri
NTNU
1 shared publication - Arild Saasen
University of Stavanger
1 shared publication - Eric Cayeux
NORCE
1 shared publication
Latest Publications
- Open Access
- 26 August 2026
- Published by Stavanger University Library in Annual Transactions of the Nordic Rheology Society
- Vol. 34, 105-112
The Effect of Pre-Shear Protocol for a Thixotropic Fluid
Recent studies have proposed pre-shear protocols that aim to negate directional bias and improve repeatability using a reset step: a short duration rotation in the opposite direction of the final step in the pre-shear. This should leave the sample in a directionally unbiased state, with little or no residual stress. Using a highly thixotropic fluid, we have tested four different pre-shear protocols: one-directional rotation, rotation with reset as suggested by Choi and Rogers (2020), large-amplitude oscillations with reset proposed by Donley et al. (2026) and a synthesis of the two latter. For the present material, a low-concentration aqueous solution of Laponite® -RD, our results do not indicate that either one of these protocols is better suited than the others, nor, in fact, that they perform better than using no pre-shear protocol at all.
- 26 August 2026
- Published by Stavanger University Library in Annual Transactions of the Nordic Rheology Society
- Vol. 34, 105-112
Open AccessThe Effect of Pre-Shear Protocol for a Thixotropic Fluid
Recent studies have proposed pre-shear protocols that aim to negate directional bias and improve repeatability using a reset step: a short duration rotation in the opposite direction of the final step in the pre-shear. This should leave the sample in a directionally unbiased state, with little or no residual stress. Using a highly thixotropic fluid, we have tested four different pre-shear protocols: one-directional rotation, rotation with reset as suggested by Choi and Rogers (2020), large-amplitude oscillations with reset proposed by Donley et al. (2026) and a synthesis of the two latter. For the present material, a low-concentration aqueous solution of Laponite® -RD, our results do not indicate that either one of these protocols is better suited than the others, nor, in fact, that they perform better than using no pre-shear protocol at all.
- 1 April 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (4)
Fluid forces in eccentric annular geometries with rotating and orbiting inner cylinder
This study investigates fluid forces and viscous torque on an inner cylinder that simultaneously rotates about its own axis and orbits within an outer cylinder. This problem is particularly relevant for industrial applications such as drill string dynamics and journal bearings, where understanding fluid-structure interactions is crucial for predicting and controlling system behavior. We combine analytical solutions valid in the weakly inertial regime with computational fluid dynamics simulations to examine how these forces depend on the annulus geometry, eccentricity, and the relative magnitudes of rotational and orbital motion. Our results show that available analytical solutions provide fair predictions of the radial and tangential force components, as well as the viscous torque when inertial effects are weak. For stronger inertial effects, we develop approximate expressions that extend beyond the weakly inertial regime. We identify a geometry-dependent orbital speed at which the tangential force component vanishes, and show that the stability of orbital motion depends on the aspect ratio. High aspect ratios (narrow annulus) lead to significant pressure build-up and net centralizing forces, while lower aspect ratios (wider annulus) may permit stable orbital configurations. The developed expressions are particularly relevant for vibration modeling of drill strings or journal bearings where the structure is coupled with the fluid forces.
- 1 April 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (4)
Fluid forces in eccentric annular geometries with rotating and orbiting inner cylinder
This study investigates fluid forces and viscous torque on an inner cylinder that simultaneously rotates about its own axis and orbits within an outer cylinder. This problem is particularly relevant for industrial applications such as drill string dynamics and journal bearings, where understanding fluid-structure interactions is crucial for predicting and controlling system behavior. We combine analytical solutions valid in the weakly inertial regime with computational fluid dynamics simulations to examine how these forces depend on the annulus geometry, eccentricity, and the relative magnitudes of rotational and orbital motion. Our results show that available analytical solutions provide fair predictions of the radial and tangential force components, as well as the viscous torque when inertial effects are weak. For stronger inertial effects, we develop approximate expressions that extend beyond the weakly inertial regime. We identify a geometry-dependent orbital speed at which the tangential force component vanishes, and show that the stability of orbital motion depends on the aspect ratio. High aspect ratios (narrow annulus) lead to significant pressure build-up and net centralizing forces, while lower aspect ratios (wider annulus) may permit stable orbital configurations. The developed expressions are particularly relevant for vibration modeling of drill strings or journal bearings where the structure is coupled with the fluid forces.
- 1 July 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (7)
Density unstable fluid displacement in vertical annuli
We study displacement flows involving pairs of Newtonian and shear-thinning fluids in vertical annular geometries using experimental and computational methods. This investigation is motivated by the primary cementing of casing strings, which is part of the well construction operation. In displacement scenarios that involve density-unstable fluid pairs, it is well-known that buoyancy can increase the inter-mixing between fluids and hence contaminate cementing fluids due to gravity-driven instabilities. Our study seeks to investigate how the imposed flow rate, the degree of inner pipe centralization, and the viscosity of the fluids affect the displacement efficiency in such cases. The study complements our recent paper [R. Zhang et al., “Vertical cementing displacement flows of shear-thinning fluids,” Phys. Fluids 35, 113110 (2023)], which focused on density-stable configurations, and here we consider the more challenging, density-unstable displacement flows. Our experiments and three-dimensional computational results are in general agreement. The results show that displacements improve for viscosity-stable conditions, i.e., when the displacing fluid is the more viscous fluid. Characteristic fingering patterns occur in the interface region of the fluids for viscosity-unstable conditions. The eccentricity of the inner pipe is seen to promote the channeling of fluids, and viscosity-unstable conditions can exacerbate this effect further. A degree of stabilization of density unstable displacements can be achieved by increasing the imposed flow rate and the viscosity of the fluids while maintaining a stable viscosity ratio.
- 1 July 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (7)
Density unstable fluid displacement in vertical annuli
We study displacement flows involving pairs of Newtonian and shear-thinning fluids in vertical annular geometries using experimental and computational methods. This investigation is motivated by the primary cementing of casing strings, which is part of the well construction operation. In displacement scenarios that involve density-unstable fluid pairs, it is well-known that buoyancy can increase the inter-mixing between fluids and hence contaminate cementing fluids due to gravity-driven instabilities. Our study seeks to investigate how the imposed flow rate, the degree of inner pipe centralization, and the viscosity of the fluids affect the displacement efficiency in such cases. The study complements our recent paper [R. Zhang et al., “Vertical cementing displacement flows of shear-thinning fluids,” Phys. Fluids 35, 113110 (2023)], which focused on density-stable configurations, and here we consider the more challenging, density-unstable displacement flows. Our experiments and three-dimensional computational results are in general agreement. The results show that displacements improve for viscosity-stable conditions, i.e., when the displacing fluid is the more viscous fluid. Characteristic fingering patterns occur in the interface region of the fluids for viscosity-unstable conditions. The eccentricity of the inner pipe is seen to promote the channeling of fluids, and viscosity-unstable conditions can exacerbate this effect further. A degree of stabilization of density unstable displacements can be achieved by increasing the imposed flow rate and the viscosity of the fluids while maintaining a stable viscosity ratio.
- 10 April 2024
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 29 (07) , 3516-3530
Effects of Noncrosslinked Polyvinyl Alcohol Fluid Loss Additive on the Compressive Strength and Viscosity of Class G Cement Slurries
Summary: Limiting the fluid loss from the cement slurry to the adjacent formation by using additives is essential for maintaining the slurry’s water/cement ratio. The present work focuses on the effect of noncrosslinked polyvinyl alcohol additive (PVOH), a widely used fluid loss additive (FLA), on the compression strength and rheological behavior of Class G cement pastes. Results of the current study show that the PVOH surfactant characteristic and its absorptive mechanism interfere not only with the hydration process but also with the physical properties and compressive strength of cement pastes, such as porosity, permeability, and early age strength, which revealed the importance of using a defoamer when PVOH is present in the mixture. In the absence of a defoamer, the PVOH additive generates foam in the mixed cement paste samples, which results in increased porosity and reduced compressive strength of the hardened cement paste. Moreover, regarding rheology, increasing the PVOH concentration increased the effective viscosity when evaluating flow curves. Therefore, this study demonstrates a systematic method for assessing the possible effects of cement paste additives, such as PVOH and defoamer, providing a physical and mechanical approach rather than just chemical to evaluate additives’ influence on the mixtures. This method should consider different additives in combination with PVOH to test cement paste stability and to obtain specific working recipes.
- 10 April 2024
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 29 (07) , 3516-3530
Effects of Noncrosslinked Polyvinyl Alcohol Fluid Loss Additive on the Compressive Strength and Viscosity of Class G Cement Slurries
Summary: Limiting the fluid loss from the cement slurry to the adjacent formation by using additives is essential for maintaining the slurry’s water/cement ratio. The present work focuses on the effect of noncrosslinked polyvinyl alcohol additive (PVOH), a widely used fluid loss additive (FLA), on the compression strength and rheological behavior of Class G cement pastes. Results of the current study show that the PVOH surfactant characteristic and its absorptive mechanism interfere not only with the hydration process but also with the physical properties and compressive strength of cement pastes, such as porosity, permeability, and early age strength, which revealed the importance of using a defoamer when PVOH is present in the mixture. In the absence of a defoamer, the PVOH additive generates foam in the mixed cement paste samples, which results in increased porosity and reduced compressive strength of the hardened cement paste. Moreover, regarding rheology, increasing the PVOH concentration increased the effective viscosity when evaluating flow curves. Therefore, this study demonstrates a systematic method for assessing the possible effects of cement paste additives, such as PVOH and defoamer, providing a physical and mechanical approach rather than just chemical to evaluate additives’ influence on the mixtures. This method should consider different additives in combination with PVOH to test cement paste stability and to obtain specific working recipes.
- 9 February 2024
- Published by Springer Nature
- p. 280-297
Influence of Viscosity on Density-Unstable Fluid-Fluid Displacement in Inclined Eccentric Annuli
- 9 February 2024
- Published by Springer Nature
- p. 280-297
Influence of Viscosity on Density-Unstable Fluid-Fluid Displacement in Inclined Eccentric Annuli
- Open Access
- 21 June 2023
- Published by Society of Petroleum Engineers (SPE) in SPE Drilling & Completion
- Vol. 38 (04) , 682-695
Pipe Viscometer for Continuous Viscosity and Density Measurement of Oil Well Barrier Materials
Summary: The barrier material is a crucial component for wells, as it provides mechanical support to the casing and prevents the uncontrolled flow of formation fluids, ensuring zonal isolation. One of the essential prerequisites for the success of cementing an oil and gas well is the efficient removal of in-situ fluids and their adequate replacement by the barrier material. The quality of the mud displacement is affected by both the density and the viscosity hierarchy among subsequent fluids. Consequently, accurate and reliable measurement of fluid properties can help ensure consistent large-scale mixing of cementing fluids and verification that the properties of the mixed fluid are according to plan. In this paper, we investigate the implementation of a pipe viscometer for future automated measurements of density and viscosity of materials for zonal isolation and perform a sequential validation of the viscometer that starts with small-scale batch mixing and characterization of particle-free calibration liquids, followed by conventional Class G cement and selected new barrier materials. Finally, a larger-scale validation of the pipe viscometer was performed by integrating it into a yard-scale batch mixer for in-line characterization of expanding Class G oilwell cement mixing. In all cases, flow curves derived from pipe viscosity measurements were compared with offline measurements using a rheometer and a conventional oilfield viscometer. After a series of measurements and comparisons, the investigated in-line measurement system proved adequate for viscosity estimation. The flow curve of the barrier materials showed results similar to measurements using a conventional viscometer, validating the proposed test configuration to continuously measure the rheological behavior of the barrier material. The pipe viscometer flow curves are generally found to be in good quantitative agreement with independent viscometer characterization of the fluids, although some of the pipe viscometer measurements likely exhibited entrance length effects. Future improvements to the pipe viscometer design involve the assessment of even longer pipe sections to allow full flow development at the highest shear rate range and possibly different pipe diameters to improve the measurement resolution of low-shear rate viscosity.
- 21 June 2023
- Published by Society of Petroleum Engineers (SPE) in SPE Drilling & Completion
- Vol. 38 (04) , 682-695
Open AccessPipe Viscometer for Continuous Viscosity and Density Measurement of Oil Well Barrier Materials
Summary: The barrier material is a crucial component for wells, as it provides mechanical support to the casing and prevents the uncontrolled flow of formation fluids, ensuring zonal isolation. One of the essential prerequisites for the success of cementing an oil and gas well is the efficient removal of in-situ fluids and their adequate replacement by the barrier material. The quality of the mud displacement is affected by both the density and the viscosity hierarchy among subsequent fluids. Consequently, accurate and reliable measurement of fluid properties can help ensure consistent large-scale mixing of cementing fluids and verification that the properties of the mixed fluid are according to plan. In this paper, we investigate the implementation of a pipe viscometer for future automated measurements of density and viscosity of materials for zonal isolation and perform a sequential validation of the viscometer that starts with small-scale batch mixing and characterization of particle-free calibration liquids, followed by conventional Class G cement and selected new barrier materials. Finally, a larger-scale validation of the pipe viscometer was performed by integrating it into a yard-scale batch mixer for in-line characterization of expanding Class G oilwell cement mixing. In all cases, flow curves derived from pipe viscosity measurements were compared with offline measurements using a rheometer and a conventional oilfield viscometer. After a series of measurements and comparisons, the investigated in-line measurement system proved adequate for viscosity estimation. The flow curve of the barrier materials showed results similar to measurements using a conventional viscometer, validating the proposed test configuration to continuously measure the rheological behavior of the barrier material. The pipe viscometer flow curves are generally found to be in good quantitative agreement with independent viscometer characterization of the fluids, although some of the pipe viscometer measurements likely exhibited entrance length effects. Future improvements to the pipe viscometer design involve the assessment of even longer pipe sections to allow full flow development at the highest shear rate range and possibly different pipe diameters to improve the measurement resolution of low-shear rate viscosity.
- Open Access
- 1 January 2019
- Published by Walter de Gruyter GmbH in Applied Rheology
- Vol. 29 (1) , 173-181
Concentric cylinder viscometer flows of Herschel-Bulkley fluids
Drilling fluids and well cements are example non-Newtonian fluids that are used for geothermal and petroleum well construction. Measurement of the non-Newtonian fluid viscosities are normally performed using a concentric cylinder Couette geometry, where one of the cylinders rotates at a controlled speed or under a controlled torque. In this paper we address Couette flow of yield stress shear thinning fluids in concentric cylinder geometries.We focus on typical oilfield viscometers and discuss effects of yield stress and shear thinning on fluid yielding at low viscometer rotational speeds and errors caused by the Newtonian shear rate assumption. We relate these errors to possible implications for typical wellbore flows.
- 1 January 2019
- Published by Walter de Gruyter GmbH in Applied Rheology
- Vol. 29 (1) , 173-181
Open AccessConcentric cylinder viscometer flows of Herschel-Bulkley fluids
Drilling fluids and well cements are example non-Newtonian fluids that are used for geothermal and petroleum well construction. Measurement of the non-Newtonian fluid viscosities are normally performed using a concentric cylinder Couette geometry, where one of the cylinders rotates at a controlled speed or under a controlled torque. In this paper we address Couette flow of yield stress shear thinning fluids in concentric cylinder geometries.We focus on typical oilfield viscometers and discuss effects of yield stress and shear thinning on fluid yielding at low viscometer rotational speeds and errors caused by the Newtonian shear rate assumption. We relate these errors to possible implications for typical wellbore flows.
- 8 June 2014
- Published by ASME International
Estimation of Weight and Torque on Bit: Assessment of Uncertainties, Correction and Calibration Methods
The efficiency of a drilling operation is to a great extent governed by how well one is able to optimize the rate of penetration (ROP) throughout each stage of the operation. ROP optimization normally involves balancing drilling speed on the one hand with acceptable wear to the drill bit on the other. The bit lifetime is largely determined by the mechanical conditions at the bit-formation rock interface and the weight on bit (WOB) and torque on bit (TOB) provide important information related to the working condition of the bit. The accuracy of WOB and TOB measurements can thus become a determining factor for the overall drilling efficiency. Due to the low bandwidth of downhole mud pulse-based telemetry systems, the WOB and the TOB are generally derived from surface measurements, i.e. from the hook load and the top-drive torque. Field experience indicates that a WOB derived from surface measurements can be of limited accuracy, such as when surface measurements suggest a negative WOB even though the ROP is positive, or when high sampling rate and high precision downhole measurements confirm a large discrepancy between the memory recorded downhole data and the estimated values based on the measurements made at the level of the hoisting equipment and the top-drive. The reason for these inconsistencies is simply that there are numerous physical processes taking place between the bit and the surface measurements that are normally not accounted for when WOB and TOB are estimated. This paper reviews and analyses the sources of these deviations and models the physical processes in order to quantify the precision for which the WOB and the TOB can be ascertained using solely surface measurements. Methods are also proposed that compensate for certain side effects by utilizing real-time torque and drag and hydraulic calculations.
- 8 June 2014
- Published by ASME International
Estimation of Weight and Torque on Bit: Assessment of Uncertainties, Correction and Calibration Methods
The efficiency of a drilling operation is to a great extent governed by how well one is able to optimize the rate of penetration (ROP) throughout each stage of the operation. ROP optimization normally involves balancing drilling speed on the one hand with acceptable wear to the drill bit on the other. The bit lifetime is largely determined by the mechanical conditions at the bit-formation rock interface and the weight on bit (WOB) and torque on bit (TOB) provide important information related to the working condition of the bit. The accuracy of WOB and TOB measurements can thus become a determining factor for the overall drilling efficiency. Due to the low bandwidth of downhole mud pulse-based telemetry systems, the WOB and the TOB are generally derived from surface measurements, i.e. from the hook load and the top-drive torque. Field experience indicates that a WOB derived from surface measurements can be of limited accuracy, such as when surface measurements suggest a negative WOB even though the ROP is positive, or when high sampling rate and high precision downhole measurements confirm a large discrepancy between the memory recorded downhole data and the estimated values based on the measurements made at the level of the hoisting equipment and the top-drive. The reason for these inconsistencies is simply that there are numerous physical processes taking place between the bit and the surface measurements that are normally not accounted for when WOB and TOB are estimated. This paper reviews and analyses the sources of these deviations and models the physical processes in order to quantify the precision for which the WOB and the TOB can be ascertained using solely surface measurements. Methods are also proposed that compensate for certain side effects by utilizing real-time torque and drag and hydraulic calculations.