Randall F. Lind
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Randall F. Lind has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Brian Post
Manufacturing Science Division, Oak Ridge National Laboratory, Knoxville, TN 37932, USA
2 shared publications - Brett Gibson Compton
Mechanical, Aerospace, and Biomedical Engineering Department University of Tennessee Knoxville Tennessee USA
1 shared publication - Chad Duty
Bredesen Center for Interdisciplinary Research and Graduate Education, The University of Tennessee, Knoxville, TN 37996, USA
1 shared publication - Donald Erdman
Manufacturing Demonstration Facility, Oak Ridge National Laboratory, Oak Ridge, Tennessee, USA
1 shared publication - Joshua E. Vaughan
Manufacturing Science Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831, USA
1 shared publication - Lonnie Love
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
1 shared publication
Latest Publications
- 23 September 2021
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 14 (2) , 1-17
Kinematics of a Cable-Driven Robotic Platform for Large-Scale Additive Manufacturing
Concrete additive manufacturing (AM) is a growing field of research. However, on-site, large-scale concrete additive manufacturing requires motion platforms that are difficult to implement with conventional rigid-link robotic systems. This article presents a new kinematic arrangement for a deployable cable-driven robot intended for on-site AM. The kinematics of this robot are examined to determine if they meet the requirements for this application, the wrench feasible workspace (WFW) is examined, and the physical implementation of a prototype is also presented. Data collected from the physical implementation of the proposed system are analyzed, and the results support its suitability for the intended application. The success of this system demonstrates that this kinematic arrangement is promising for future deployable AM systems.
- 23 September 2021
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 14 (2) , 1-17
Kinematics of a Cable-Driven Robotic Platform for Large-Scale Additive Manufacturing
Concrete additive manufacturing (AM) is a growing field of research. However, on-site, large-scale concrete additive manufacturing requires motion platforms that are difficult to implement with conventional rigid-link robotic systems. This article presents a new kinematic arrangement for a deployable cable-driven robot intended for on-site AM. The kinematics of this robot are examined to determine if they meet the requirements for this application, the wrench feasible workspace (WFW) is examined, and the physical implementation of a prototype is also presented. Data collected from the physical implementation of the proposed system are analyzed, and the results support its suitability for the intended application. The success of this system demonstrates that this kinematic arrangement is promising for future deployable AM systems.
- Top Cited Papers
- 16 January 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (1) , 181-189
Structure and mechanical behavior of Big Area Additive Manufacturing (BAAM) materials
Purpose: This paper aims to investigate the deposited structure and mechanical performance of printed materials obtained during initial development of the Big Area Additive Manufacturing (BAAM) system at Oak Ridge National Laboratory. Issues unique to large-scale polymer deposition are identified and presented to reduce the learning curve for the development of similar systems. Design/methodology/approach: Although the BAAM’s individual extruded bead is 10-20× larger (∼9 mm) than the typical small-scale systems, the overall characteristics of the deposited material are very similar. This study relates the structure of BAAM materials to the material composition, deposition parameters and resulting mechanical performance. Findings: Materials investigated during initial trials are suitable for stiffness-limited applications. The strength of printed materials can be significantly reduced by voids and imperfect fusion between layers. Deposited material was found to have voids between adjacent beads and micro-porosity within a given bead. Failure generally occurs at interfaces between adjacent beads and successive layers, indicating imperfect contact area and polymer fusion. Practical implications: The incorporation of second-phase reinforcement in printed materials can significantly improve stiffness but can result in notable anisotropy that needs to be accounted for in the design of BAAM-printed structures. Originality/value: This initial evaluation of BAAM-deposited structures and mechanical performance will guide the current research effort for improving interlaminar strength and process control.
- 16 January 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (1) , 181-189
Top Cited PapersStructure and mechanical behavior of Big Area Additive Manufacturing (BAAM) materials
Purpose: This paper aims to investigate the deposited structure and mechanical performance of printed materials obtained during initial development of the Big Area Additive Manufacturing (BAAM) system at Oak Ridge National Laboratory. Issues unique to large-scale polymer deposition are identified and presented to reduce the learning curve for the development of similar systems. Design/methodology/approach: Although the BAAM’s individual extruded bead is 10-20× larger (∼9 mm) than the typical small-scale systems, the overall characteristics of the deposited material are very similar. This study relates the structure of BAAM materials to the material composition, deposition parameters and resulting mechanical performance. Findings: Materials investigated during initial trials are suitable for stiffness-limited applications. The strength of printed materials can be significantly reduced by voids and imperfect fusion between layers. Deposited material was found to have voids between adjacent beads and micro-porosity within a given bead. Failure generally occurs at interfaces between adjacent beads and successive layers, indicating imperfect contact area and polymer fusion. Practical implications: The incorporation of second-phase reinforcement in printed materials can significantly improve stiffness but can result in notable anisotropy that needs to be accounted for in the design of BAAM-printed structures. Originality/value: This initial evaluation of BAAM-deposited structures and mechanical performance will guide the current research effort for improving interlaminar strength and process control.