Taj-Dine Lamcharfi
Research Subjects
Research Interests
Taj-Dine Lamcharfi has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Farid Abdi
Signals, Systems and Components Laboratory, Faculty of Sciences and Technologies, Sidi Mohamed Ben Abdellah University, Fes 30000, Morocco
5 shared publications - Najwa Gouitaa
Signals, Systems and Components Laboratory (LSSC), Electrical Engineering Department, University Sidi Mohamed Ben Abdellah USMBA, FST. Fez, Imouzzer Road B.P. 2202, Morocco
4 shared publications - Fatima Zahra Ahjyaje
Signals, Systems and Components Laboratory, Faculty of Science and Technology of Fez, University Sidi Mohammed Ben Abdellah USMBA, Route d’Imouzzer, Fez P.O. Box 2202, Morocco
2 shared publications M. Haddad
Materials and Archaeomaterials Spectrometry Laboratory (LASMAR), Research Unit Associated with CNRST (URAC11), Moulay-Ismail University, Faculty of Sciences, 50000 Meknès, Morocco
2 shared publications- Najiba El Amrani El Idrissi
Signal, Systems and Components Laboratory, Faculty of Sciences & Technologies, Sidi Mohamed Ben Abdellah University, Fez 30000, Morocco
2 shared publications A. Harrach
Condensed Matter Chemistry Laboratory, Sidi Mohammed Ben Abdellah University, BP 2202, Route d'Imouzzer, Faculty of Science and Technology of Fez, BP 2202, Fez, Morocco
1 shared publication
Latest Publications
- Open Access
Enhancing Dielectric, Electrical, and Gas Sensing Properties of CaFeO3−δ Through Sintering Temperature Optimization
This research aims to investigate the modifications of the structural, dielectric, and sensing properties of CaFeO3−δ ceramics produced by solid-state reaction induced by varying sintering temperatures in the range of 1000–1200 °C. A single crystallographic orthorhombic (Pcmn) structure was revealed by X-ray diffraction with Rietveld analysis, both for the powders and sintered ceramics, irrespective of the sintering temperature. The increase in the sintering temperature induces better densification and a larger grain size. Dielectric measurements reveal a pronounced enhancement of the relative permittivity, reaching 2 × 105 at 1 kHz and 330 °C for the sample sintered at 1200 °C/4 h. This composition also displays the highest electrical conductivity, 0.4 S/m at 1 MHz. Cole–Cole analysis indicates a clear deviation from ideal Debye behavior, while the relaxational features of the dielectric permittivity suggest a strong correlation between the dielectric response and Fe-related conduction mechanisms. Gas sensing tests show that the ferrite ceramics exhibit consistent ethanol response trends. The ceramic sintered at 1200 °C/4 h achieved the highest sensitivity, of 56.28%, which can be attributed to its higher density, larger ceramic grains, and reduced low-frequency conductivity. The CaFeO3−δ ceramic sintered at 1200 °C/4 h shows a combination of high permittivity, enhanced conductivity, and strong ethanol sensitivity, making it a promising material for dielectric components, capacitive devices, and gas sensing applications.
Open AccessEnhancing Dielectric, Electrical, and Gas Sensing Properties of CaFeO3−δ Through Sintering Temperature Optimization
This research aims to investigate the modifications of the structural, dielectric, and sensing properties of CaFeO3−δ ceramics produced by solid-state reaction induced by varying sintering temperatures in the range of 1000–1200 °C. A single crystallographic orthorhombic (Pcmn) structure was revealed by X-ray diffraction with Rietveld analysis, both for the powders and sintered ceramics, irrespective of the sintering temperature. The increase in the sintering temperature induces better densification and a larger grain size. Dielectric measurements reveal a pronounced enhancement of the relative permittivity, reaching 2 × 105 at 1 kHz and 330 °C for the sample sintered at 1200 °C/4 h. This composition also displays the highest electrical conductivity, 0.4 S/m at 1 MHz. Cole–Cole analysis indicates a clear deviation from ideal Debye behavior, while the relaxational features of the dielectric permittivity suggest a strong correlation between the dielectric response and Fe-related conduction mechanisms. Gas sensing tests show that the ferrite ceramics exhibit consistent ethanol response trends. The ceramic sintered at 1200 °C/4 h achieved the highest sensitivity, of 56.28%, which can be attributed to its higher density, larger ceramic grains, and reduced low-frequency conductivity. The CaFeO3−δ ceramic sintered at 1200 °C/4 h shows a combination of high permittivity, enhanced conductivity, and strong ethanol sensitivity, making it a promising material for dielectric components, capacitive devices, and gas sensing applications.
- Open Access
- 1 March 2026
- Published by UAB Sustainability for Regions in Insights into Regional Development
- Vol. 8 (1) , 43-54
Turning the sun into power: the NOUR model for boosting solar energy in Northern Europe
- 1 March 2026
- Published by UAB Sustainability for Regions in Insights into Regional Development
- Vol. 8 (1) , 43-54
Open AccessTurning the sun into power: the NOUR model for boosting solar energy in Northern Europe
- Open Access
- 1 March 2025
- Published by UAB Sustainability for Regions in Insights into Regional Development
- Vol. 7 (1) , 10-23
Renewable energy landscapes: a comparative analysis of Lithuania's, Europe's, and Africa's green strategies
- 1 March 2025
- Published by UAB Sustainability for Regions in Insights into Regional Development
- Vol. 7 (1) , 10-23
Open AccessRenewable energy landscapes: a comparative analysis of Lithuania's, Europe's, and Africa's green strategies
- Open Access
- 25 January 2025
- Published by Universitas Gadjah Mada in Indonesian Journal of Chemistry
- Vol. 25 (1) , 13-23
Study of Structural, Dielectric, and Phase Transition of Strontium Doped BaTiO3
In this paper, we studied the effect of strontium doping on the structural, microstructural, dielectric, and electrical properties of Ba1-xSrxTiO3 (BSxT) ceramics prepared via the sol-gel method, with x = 0.00 to 0.15. The results obtained from the X-ray diffraction spectrum confirmed the creation of the pure perovskite structure, with the diffraction peaks of the BSxT shifting toward the bigger 2θ with increasing Sr content. Scanning electron microscopy images show that the grain size of the BSxT ceramics decreases with increasing Sr content. An increase in Sr content appears to lower the activation energy by the factor of 0.16 meV/mol% and to decrease Curie temperature by the factor of 3.34 °C/mol%. Furthermore, in case of 15 mol% of Sr addition, the dielectric constant value is increased about twice. Moreover, the relationship between grain sizes and dielectric properties was also investigated. Using the frequency measurement method (up to 2 MHz in a step of 1 kHz), we are able to determine the temperature of transition without using the conventional method.
- 25 January 2025
- Published by Universitas Gadjah Mada in Indonesian Journal of Chemistry
- Vol. 25 (1) , 13-23
Open AccessStudy of Structural, Dielectric, and Phase Transition of Strontium Doped BaTiO3
In this paper, we studied the effect of strontium doping on the structural, microstructural, dielectric, and electrical properties of Ba1-xSrxTiO3 (BSxT) ceramics prepared via the sol-gel method, with x = 0.00 to 0.15. The results obtained from the X-ray diffraction spectrum confirmed the creation of the pure perovskite structure, with the diffraction peaks of the BSxT shifting toward the bigger 2θ with increasing Sr content. Scanning electron microscopy images show that the grain size of the BSxT ceramics decreases with increasing Sr content. An increase in Sr content appears to lower the activation energy by the factor of 0.16 meV/mol% and to decrease Curie temperature by the factor of 3.34 °C/mol%. Furthermore, in case of 15 mol% of Sr addition, the dielectric constant value is increased about twice. Moreover, the relationship between grain sizes and dielectric properties was also investigated. Using the frequency measurement method (up to 2 MHz in a step of 1 kHz), we are able to determine the temperature of transition without using the conventional method.
- Open Access
- 20 August 2021
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 33 (9) , 2000-2006
Effect of Zinc Doping on the Electrical and Dielectric Properties of CCTO Compound Synthesized by Solid-State Method
In this work, the influence of zinc doping on structural and dielectric properties of CaCu(3-x)ZnxTi4O12 (CCZxTO with x = 0, 2.5, 5, 7.5, 10, 12.5 and 15%) ceramics sintered at 1000 ºC for 8 h was studied. The ceramic samples were prepared by the conventional solid-state and calcined at 1050 ºC for 4 h. The X-ray diffraction (XRD) analysis of pure and Zn-doped CCTO were analyzed by using Rietveld refinement with cubic CCTO phase with no trace impurity phase. The scanning electron microscopy (SEM) investigation showed that for Zn-doped CCTO, the grains distributions were homogenous with average sizes which decreased with increasing of Zn concentration. The dielectric permittivity as function of temperature showed two dielectric anomalies (weakly and strong) and the dielectric constant value largely decreased for x = 2.5%, which is about tree magnitude smaller than the pure ceramic. Then it increased and reached a maximum at x = 10%, which is larger than the value of pure ceramic. And for x > 10%, the dielectric constant decreased for about two magnitude smaller than the ceramic at x = 10%. The cole-cole diagramm for all the samples showed existence of two semi-arcs attributed to the grains and grains boundaries. It was found that the Rg values were much smaller than the Rgb value. This give an evidance on the formation of interior barrier layer capacity (IBLC).
- 20 August 2021
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 33 (9) , 2000-2006
Open AccessEffect of Zinc Doping on the Electrical and Dielectric Properties of CCTO Compound Synthesized by Solid-State Method
In this work, the influence of zinc doping on structural and dielectric properties of CaCu(3-x)ZnxTi4O12 (CCZxTO with x = 0, 2.5, 5, 7.5, 10, 12.5 and 15%) ceramics sintered at 1000 ºC for 8 h was studied. The ceramic samples were prepared by the conventional solid-state and calcined at 1050 ºC for 4 h. The X-ray diffraction (XRD) analysis of pure and Zn-doped CCTO were analyzed by using Rietveld refinement with cubic CCTO phase with no trace impurity phase. The scanning electron microscopy (SEM) investigation showed that for Zn-doped CCTO, the grains distributions were homogenous with average sizes which decreased with increasing of Zn concentration. The dielectric permittivity as function of temperature showed two dielectric anomalies (weakly and strong) and the dielectric constant value largely decreased for x = 2.5%, which is about tree magnitude smaller than the pure ceramic. Then it increased and reached a maximum at x = 10%, which is larger than the value of pure ceramic. And for x > 10%, the dielectric constant decreased for about two magnitude smaller than the ceramic at x = 10%. The cole-cole diagramm for all the samples showed existence of two semi-arcs attributed to the grains and grains boundaries. It was found that the Rg values were much smaller than the Rgb value. This give an evidance on the formation of interior barrier layer capacity (IBLC).
- Open Access
- 16 February 2021
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 33 (3) , 665-670
Effect of Cu Doping on Structural and Dielectric Properties of Pb1-xCux(Zr0.52Ti0.48)O3(PCxZT) (0 ≤ x ≤ 0.2) Ceramics Prepared by Sol-Gel Method
In present work, the structural and dielectric properties of Pb1-xCuxZr0.52Ti0.48O3 (PCxZT) ceramics where x = 0. 0.025, 0.05, 0.075, 0.10, 0.15 and 0.20 were studied. Powder of the compositions (PCxZT) was obtained by sol-gel route, the powders were calcined at 700 ºC for 4 h and sintered at 1100 ºC for 4 h. X-ray diffraction analysis and Raman spectroscopy suggest the formation of mixed-phase of tetragonal and rhombohedral structure which was confirmed by Rietveld refinement. Dielectric measurements of the compounds were studied as a function of temperature (from room temperature to 420 ºC at different frequencies) and as a function of frequency (from 100 Hz to 2 MHz at different temperatures). The temperature variation of the real permittivity gives evidence of the ferroelectric phase transition as well as of the resonance behaviour also observed in the dielectric permittivity frequency-dependent variation.
- 16 February 2021
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 33 (3) , 665-670
Open AccessEffect of Cu Doping on Structural and Dielectric Properties of Pb1-xCux(Zr0.52Ti0.48)O3(PCxZT) (0 ≤ x ≤ 0.2) Ceramics Prepared by Sol-Gel Method
In present work, the structural and dielectric properties of Pb1-xCuxZr0.52Ti0.48O3 (PCxZT) ceramics where x = 0. 0.025, 0.05, 0.075, 0.10, 0.15 and 0.20 were studied. Powder of the compositions (PCxZT) was obtained by sol-gel route, the powders were calcined at 700 ºC for 4 h and sintered at 1100 ºC for 4 h. X-ray diffraction analysis and Raman spectroscopy suggest the formation of mixed-phase of tetragonal and rhombohedral structure which was confirmed by Rietveld refinement. Dielectric measurements of the compounds were studied as a function of temperature (from room temperature to 420 ºC at different frequencies) and as a function of frequency (from 100 Hz to 2 MHz at different temperatures). The temperature variation of the real permittivity gives evidence of the ferroelectric phase transition as well as of the resonance behaviour also observed in the dielectric permittivity frequency-dependent variation.
- 18 March 2011
- Published by Wiley in Crystal Research and Technology
- Vol. 46 (4) , 368-372
Synthesis and characterization of magnesium doped lead titanate
Magnesium (Mg) doped lead titanate powders (PT: Mg) ceramics, with various Mg contents (0, 2.5, 5, 7.5, 10, 12.5, 15, 17.5, 20, and 30 mole %), are prepared by the sol‐gel method and characterized by X‐Ray diffraction (XRD), scanning electron microscopy (SEM) and Raman spectroscopy. XRD results show that the magnesium diminishes the lattice tetragonality of PT:Mg. The average particle size and morphology were studied by SEM. The investigations done by Raman spectroscopy allow the analyzis of the substitution mechanism behavior related to the Mg incorporation into PT structure. A concentration threshold appears around 10% of Mg corresponding in a change of the compensation process with Mg2+ ions replacing Pb2+ ions below and both Pb2+ and Ti4+ above.
- 18 March 2011
- Published by Wiley in Crystal Research and Technology
- Vol. 46 (4) , 368-372
Synthesis and characterization of magnesium doped lead titanate
Magnesium (Mg) doped lead titanate powders (PT: Mg) ceramics, with various Mg contents (0, 2.5, 5, 7.5, 10, 12.5, 15, 17.5, 20, and 30 mole %), are prepared by the sol‐gel method and characterized by X‐Ray diffraction (XRD), scanning electron microscopy (SEM) and Raman spectroscopy. XRD results show that the magnesium diminishes the lattice tetragonality of PT:Mg. The average particle size and morphology were studied by SEM. The investigations done by Raman spectroscopy allow the analyzis of the substitution mechanism behavior related to the Mg incorporation into PT structure. A concentration threshold appears around 10% of Mg corresponding in a change of the compensation process with Mg2+ ions replacing Pb2+ ions below and both Pb2+ and Ti4+ above.