Zhigang Liu
Research Subjects
Zhigang Liu has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Guoliang Xiong
State Key Laboratory of Performance Monitoring Protecting of Rail Transit Infrastructure, East China Jiaotong University, Nanchang 330013, China
2 shared publications - Long Zhang
The Department of Electrical and Electronic Engineering, The University of Manchester, Manchester M13 9PL, UK
2 shared publications - Fengxia Han
Beijing Information Science & Technology University
1 shared publication - Hao Huang
Key Laboratory of Modern Transportation and Logistics of Jiangxi Province, Jiangxi Vocational and Technical College of Communications, Nanchang 330013, China
1 shared publication Honglin Fan
Beijing Information Science and Technology University
1 shared publication- Qian Xiao
Key Laboratory of Intelligent Operation and Maintenance Technology and Equipment in Transportation, Ministry of Education, East China Jiaotong University, Nanchang 330000, China
1 shared publication
Latest Publications
- Open Access
- 1 September 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (18) , 185512
Siamese ordinal prototypical network with S-transform for few-shot damage severity assessment of high-speed train bearings
Axle box bearings are critical rotating components in the running gear of high-speed trains, and their damage condition directly affects the operational safety of trains. To address the problems of non-stationary vibration signals, limited fault samples, and the ordinal degradation characteristics of bearing damage levels, this paper proposes a bearing damage severity assessment method based on S-transform (ST) and a Siamese ordinal prototypical network (ProtoNet). First, the ST is used to convert one-dimensional vibration signals into two-dimensional time–frequency images to enhance fault feature representation. Then, a Swin Transformer is employed to extract features from the time–frequency images, and a Siamese network is constructed to optimize the feature space distribution through contrastive loss. On this basis, an ordinal ProtoNet combined with the Wasserstein distance loss is introduced to impose ordinal constraints on different damage levels, enabling effective identification of bearing damage severity. Experiments are conducted on a high-speed train bearing vibration dataset under a few-shot setting, and comparisons are made with convolutional neural network (CNN), ProtoNet, Siamese CNN, ResNet18, Swin Transformer, and convolutional block attention module-residual network-Siamese models. The results show that the proposed method achieves a classification accuracy of 93.8% in a four-class bearing condition recognition task, outperforming the compared models and demonstrating its effectiveness in small-sample bearing damage severity assessment.
- 1 September 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (18) , 185512
Open AccessSiamese ordinal prototypical network with S-transform for few-shot damage severity assessment of high-speed train bearings
Axle box bearings are critical rotating components in the running gear of high-speed trains, and their damage condition directly affects the operational safety of trains. To address the problems of non-stationary vibration signals, limited fault samples, and the ordinal degradation characteristics of bearing damage levels, this paper proposes a bearing damage severity assessment method based on S-transform (ST) and a Siamese ordinal prototypical network (ProtoNet). First, the ST is used to convert one-dimensional vibration signals into two-dimensional time–frequency images to enhance fault feature representation. Then, a Swin Transformer is employed to extract features from the time–frequency images, and a Siamese network is constructed to optimize the feature space distribution through contrastive loss. On this basis, an ordinal ProtoNet combined with the Wasserstein distance loss is introduced to impose ordinal constraints on different damage levels, enabling effective identification of bearing damage severity. Experiments are conducted on a high-speed train bearing vibration dataset under a few-shot setting, and comparisons are made with convolutional neural network (CNN), ProtoNet, Siamese CNN, ResNet18, Swin Transformer, and convolutional block attention module-residual network-Siamese models. The results show that the proposed method achieves a classification accuracy of 93.8% in a four-class bearing condition recognition task, outperforming the compared models and demonstrating its effectiveness in small-sample bearing damage severity assessment.
- Open Access
- 7 August 2023
- Published by Wiley in Shock and Vibration
- Vol. 2023, 1-14
Multilevel Feature Extraction Method for Adaptive Fault Diagnosis of Railway Axle Box Bearing
Railway axle box bearing fault signal contains high Q-factor resonance and low Q-factor transient shock components with periodic transient shock features that can characterize bearing faults. However, extracting fault features is usually difficult due to noise, transmission paths, and high-amplitude accidental shocks. Therefore, to address the abovementioned problems, the multilevel feature extraction method for adaptive fault diagnosis of railway axle box bearing was proposed. This paper used the maximum second-order cyclostationary blind convolution (CYCBD) to weaken the influence of disturbances, enhancing weak transient shock components. Resonant sparse decomposition(RSSD) is used for the selection of quality factor Q due to its excellent fault feature separation property. Considering the strict fault frequency component periodicity in the envelope spectrum, the envelope spectrum multipoint kurtosis (ESMK) is proposed as a metric. The Q factor is optimized using the gray wolf optimization algorithm (GWO) to obtain an adaptive sparse decomposition method (GWO-RSSD) for extracting bearing transient fault shocks to eliminate the signal effects of high-amplitude disturbance shocks and background noise. The simulation results and measured signal analysis of railway axle box bearing show that ESMK can effectively measure periodic transient shocks under strong shock interference compared with the MED-RSSD method. Thus, GWO-RSSD can adaptively separate the optimal low-Q resonance components, verifying the methods effectiveness and superiority.
- 7 August 2023
- Published by Wiley in Shock and Vibration
- Vol. 2023, 1-14
Open AccessMultilevel Feature Extraction Method for Adaptive Fault Diagnosis of Railway Axle Box Bearing
Railway axle box bearing fault signal contains high Q-factor resonance and low Q-factor transient shock components with periodic transient shock features that can characterize bearing faults. However, extracting fault features is usually difficult due to noise, transmission paths, and high-amplitude accidental shocks. Therefore, to address the abovementioned problems, the multilevel feature extraction method for adaptive fault diagnosis of railway axle box bearing was proposed. This paper used the maximum second-order cyclostationary blind convolution (CYCBD) to weaken the influence of disturbances, enhancing weak transient shock components. Resonant sparse decomposition(RSSD) is used for the selection of quality factor Q due to its excellent fault feature separation property. Considering the strict fault frequency component periodicity in the envelope spectrum, the envelope spectrum multipoint kurtosis (ESMK) is proposed as a metric. The Q factor is optimized using the gray wolf optimization algorithm (GWO) to obtain an adaptive sparse decomposition method (GWO-RSSD) for extracting bearing transient fault shocks to eliminate the signal effects of high-amplitude disturbance shocks and background noise. The simulation results and measured signal analysis of railway axle box bearing show that ESMK can effectively measure periodic transient shocks under strong shock interference compared with the MED-RSSD method. Thus, GWO-RSSD can adaptively separate the optimal low-Q resonance components, verifying the methods effectiveness and superiority.
- Open Access
Performance Degradation Assessment of Railway Axle Box Bearing Based on Combination of Denoising Features and Time Series Information
In the existing rolling bearing performance degradation assessment methods, the input signal is usually mixed with a large amount of noise and is easily disturbed by the transfer path. The time information is usually ignored when the model processes the input signal, which affects the effect of bearing performance degradation assessment. To solve the above problems, an end-to-end performance degradation assessment model of railway axle box bearing based on a deep residual shrinkage network and a deep long short-term memory network (DRSN-LSTM) is proposed. The proposed model uses DRSN to extract local abstract features from the signal and denoises the signal to obtain the denoised feature vector, then uses deep LSTM to extract the time-series information of the signal. The healthy time-series signal of the rolling bearing is input into the DRSN-LSTM reconstruction model for training. Time-domain, frequency-domain, and time–frequency-domain features are extracted from the signal both before and after reconstruction to form a multi-domain features vector. The mean square error of the two feature vectors is used as the degradation indicator to implement the performance degradation assessment. Artificially induced defects and rolling bearings life accelerated fatigue test data verify that the proposed model is more sensitive to early failures than mathematical models, shallow networks or other deep learning models. The result is similar to the development trend of bearing failures.
Open AccessPerformance Degradation Assessment of Railway Axle Box Bearing Based on Combination of Denoising Features and Time Series Information
In the existing rolling bearing performance degradation assessment methods, the input signal is usually mixed with a large amount of noise and is easily disturbed by the transfer path. The time information is usually ignored when the model processes the input signal, which affects the effect of bearing performance degradation assessment. To solve the above problems, an end-to-end performance degradation assessment model of railway axle box bearing based on a deep residual shrinkage network and a deep long short-term memory network (DRSN-LSTM) is proposed. The proposed model uses DRSN to extract local abstract features from the signal and denoises the signal to obtain the denoised feature vector, then uses deep LSTM to extract the time-series information of the signal. The healthy time-series signal of the rolling bearing is input into the DRSN-LSTM reconstruction model for training. Time-domain, frequency-domain, and time–frequency-domain features are extracted from the signal both before and after reconstruction to form a multi-domain features vector. The mean square error of the two feature vectors is used as the degradation indicator to implement the performance degradation assessment. Artificially induced defects and rolling bearings life accelerated fatigue test data verify that the proposed model is more sensitive to early failures than mathematical models, shallow networks or other deep learning models. The result is similar to the development trend of bearing failures.