Sayed Alireza Ataie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sayed Alireza Ataie has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
A. Alizadeh Samiyan
Department of Ceramic, Materials and Energy Research Center, Karaj, Iran
1 shared publication- Fábio Ferreira
CEMMPRE, ARISE, Department of Mechanical Engineering, University of Coimbra, Rua Luís Reis Santos, 3030-788 Coimbra, Portugal
1 shared publication H. S. Kim
Graduate Institute of Ferrous and Energy Material Technology, Pohang University of Science and Technology, Pohang, Republic of Korea
1 shared publicationM. Ghanbariha
Department of Ceramic, Materials and Energy Research Center, Karaj, Iran
1 shared publication- Mohammad Farvizi
Department of Materials Engineering, Faculty of Mechanical Engineering, University of Tabriz, Tabriz, Iran
1 shared publication - Mohammad-Reza Zamani-Meymian
Department of Physics, Iran University of Science and Technology, P.O. Box 16846-13114, Tehran, Iran
1 shared publication
Latest Publications
- 29 March 2024
- Published by Springer Nature in Metals and Materials International
- Vol. 30 (9) , 2523-2539
Effect of YSZ Particle Size and Content on Microstructure, Mechanical and Tribological Properties of (CoCrFeNiAl)1−x(YSZ)x High Entropy Alloy Composites
- 29 March 2024
- Published by Springer Nature in Metals and Materials International
- Vol. 30 (9) , 2523-2539
Effect of YSZ Particle Size and Content on Microstructure, Mechanical and Tribological Properties of (CoCrFeNiAl)1−x(YSZ)x High Entropy Alloy Composites
- Open Access
Effect of Substrate Bias Voltage on Microstructure and Mechanical Properties of Cr-Nb-Ti-Zr-N-O Ceramic Thin Films Produced by Reactive Sputtering
Hard coatings are applied in various applications to protect substrates from wear and corrosion. In the present study, multi-element ceramic films are deposited by reactive sputtering. The level of substrate bias voltage (−50, −125 and −200 V) is changed to investigate the structural and mechanical properties of Cr-Nb-Ti-Zr-N thin films. Chemical analysis (using EDS, XRD and Raman spectroscopy) reveals that these thin films (with a high amount of oxygen) are composed of a nanocomposite phase structure (amorphous and nano-crystalline phases). CrO2 and NbxN crystalline phases exist in an amorphous matrix in the coatings. By increasing the substrate voltage (from −50 to −200 V), the nitrogen content (from 30 to 40 at. %) increases, and CrxN crystalline phases are generated in S125 and S200. Morphological, topological and image analysis (employing FESEM and AFM) data show that the intermediate level of substrate bias voltage (sample S125) can produce a uniform surface with minimum defect density (15%). In addition, S125 has the minimum level of roughness (16.6 nm), skewness (0.2) and kurtosis (2.8). Therefore, the hardness, toughness and wear resistance (extracted from indentation and scratch tests) of this sample is maximum (H is 24.5 GPa and H/E is 0.107), while sample S50 shows complete fracture and delamination.
Open AccessEffect of Substrate Bias Voltage on Microstructure and Mechanical Properties of Cr-Nb-Ti-Zr-N-O Ceramic Thin Films Produced by Reactive Sputtering
Hard coatings are applied in various applications to protect substrates from wear and corrosion. In the present study, multi-element ceramic films are deposited by reactive sputtering. The level of substrate bias voltage (−50, −125 and −200 V) is changed to investigate the structural and mechanical properties of Cr-Nb-Ti-Zr-N thin films. Chemical analysis (using EDS, XRD and Raman spectroscopy) reveals that these thin films (with a high amount of oxygen) are composed of a nanocomposite phase structure (amorphous and nano-crystalline phases). CrO2 and NbxN crystalline phases exist in an amorphous matrix in the coatings. By increasing the substrate voltage (from −50 to −200 V), the nitrogen content (from 30 to 40 at. %) increases, and CrxN crystalline phases are generated in S125 and S200. Morphological, topological and image analysis (employing FESEM and AFM) data show that the intermediate level of substrate bias voltage (sample S125) can produce a uniform surface with minimum defect density (15%). In addition, S125 has the minimum level of roughness (16.6 nm), skewness (0.2) and kurtosis (2.8). Therefore, the hardness, toughness and wear resistance (extracted from indentation and scratch tests) of this sample is maximum (H is 24.5 GPa and H/E is 0.107), while sample S50 shows complete fracture and delamination.