AWAnbo Wang

Anbo Wang

*This is an algorithmically generated author record based on publicly available information.

Anbo Wang has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Natural mineral fibers: conducting inhalation toxicology studies – part A: Libby Amphibole aerosol generation and characterization method development

    by Anbo Wang, Amit Gupta, Michael D. Grimm, David T. Pressburger, Barney R. Sparrow, Jamie S. Richey, John R. Shaw, Karen E. Elsass, Georgia K. Roberts, Pei-Li Yao, et al.

    Background Asbestos has been classified as a human carcinogen, and exposure may increase the risk of diseases associated with impaired respiratory function. As the range of health effects and airborne concentrations that result in health effects across asbestos-related natural mineral fiber types are not fully understood, the National Institute of Environmental Health Sciences has established a series of research studies to characterize hazards of natural mineral fibers after inhalation exposure. This paper presents the method development work of this research project. Results A prototype nose-only exposure system was fabricated to explore the feasibility of generating natural mineral fiber aerosol for in vivo inhalation toxicity studies. The prototype system consisted of a slide bar aerosol generator, a distribution/delivery system and an exposure carousel. Characterization tests conducted using Libby Amphibole 2007 (LA 2007) demonstrated the prototype system delivered stable and controllable aerosol concentration to the exposure carousel. Transmission electron microscopy (TEM) analysis of aerosol samples collected at the exposure port showed the average fiber length and width were comparable to the bulk LA 2007. TEM coupled with energy dispersive spectrometry (EDS) and selected area electron diffraction (SAED) analysis further confirmed fibers from the aerosol samples were consistent with the bulk LA 2007 chemically and physically. Conclusions Characterization of the prototype system demonstrated feasibility of generating LA 2007 fiber aerosols appropriate for in vivo inhalation toxicity studies. The methods developed in this study are suitable to apply to a multiple-carousel exposure system for a rat inhalation toxicity testing using LA 2007.


  • Open Access

    Natural mineral fibers: conducting inhalation toxicology studies—part B: development of a nose-only exposure system for repeat-exposure in vivo study of Libby amphibole aerosol

    by Anbo Wang, Amit Gupta, Michael D. Grimm, David T. Pressburger, Barney R. Sparrow, Jamie S. Richey, John R. Shaw, Karen E. Elsass, Georgia K. Roberts, Pei-Li Yao, et al.

    Background Exposure to asbestos is associated with malignant and nonmalignant respiratory disease. To strengthen the scientific basis for risk assessment on fibers, the National Institute of Environmental Health Sciences (NIEHS) has initiated a series of studies to address fundamental questions on the toxicology of naturally occurring asbestos and related mineral fibers after inhalation exposure. A prototype nose-only exposure system was previously developed and validated. The prototype system was expanded to a large-scale exposure system in this study for conducting subsequent in vivo rodent inhalation studies of Libby amphibole (LA) 2007, selected as a model fiber. Results The exposure system consisting of six exposure carousels was able to independently deliver stable LA 2007 aerosol to individual carousels at target concentrations of 0 (control group), 0.1, 0.3, 1, 3, or 10 mg/m(3). A single aerosol generator was used to provide aerosol to all carousels to ensure that exposure atmospheres were chemically and physically similar, with aerosol concentration as the only major variable among the carousels. Transmission electron microscopy (TEM) coupled with energy dispersive spectrometry (EDS) and selected area electron diffraction (SAED) analysis of aerosol samples collected at the exposure ports indicated the fiber dimensions, chemical composition, and mineralogy were equivalent across exposure carousels and were comparable to the bulk LA 2007 material. Conclusion The exposure system developed is ready for use in conducting nose-only inhalation toxicity studies of LA 2007 in rats. The exposure system is anticipated to have applicability for the inhalation toxicity evaluation of other natural mineral fibers of concern.


  • Liquid-Surface-Level Sensing Based on Transverse Pulse Train Technique

    by Bo Liu, Dorothy Yunjing Wang, Anbo Wang

    A novel technique of liquid-surface-level sensing using a transverse pulse train is reported. Liquid level was detected by the reflection time of pulse train propagation on vertical, straight hollow wire partially immersed in liquid using two kinds of reflections. One is the echo from the liquid surface and the other is from the end of the sensing wire in which propagation speed is influenced by the liquid. Both the signals can be detected in a single measurement. In this paper, the standard deviation of the interface echo method and the end echo method is 26 and 199 μm, respectively. To the best of our knowledge, the error of the interface echo method is the lowest among all acoustic-based liquid-surface-level sensors in the current market. The attenuation coefficient of the interface echo method and the end echo method in water is 0.19 and 3.77 dB/m, respectively. The combination of the end echo and the interface echo techniques and low attenuation make it suitable for long distance and highly accurate liquid-surface-level sensing.


  • Open Access

    Temperature dependence of sapphire fiber Raman scattering

    by Bo Liu, Zhihao Yu, Zhipeng Tian, Daniel Homa, Cary Hill, Anbo Wang, Gary Pickrell

    Anti-Stokes Raman scattering in sapphire fiber has been observed for the first time. Temperature dependence of Raman peaks’ intensity, frequency shift, and linewidth were also measured. Three anti-Stokes Raman peaks were observed at temperatures higher than 300°C in a 0.72-m-long sapphire fiber excited by a second-harmonic Nd YAG laser. The intensity of anti-Stokes peaks are comparable to that of Stokes peaks when the temperature increases to 1033°C. We foresee the combination of sapphire fiber Stokes and anti-Stokes measurement in use as a mechanism for ultrahigh temperature sensing.


  • Intrinsic Fabry-Pérot interferometric (IFPI) fiber pressure sensor

    by Cheng Ma, Ning Wang, Evan M. Lally, Anbo Wang

    An optical fiber Single/Multi-/Single-mode Intrinsic Fabry-Pérot Interferometer (SMS-IFPI) pressure sensor has been demonstrated using a silica tube-based pressure transducer hermetically sealed by thermal fusion bonding. The sensor, made entirely of fused silica, contains an IFPI strain sensor enclosed by a CO2 laser-bonded outer tube. A sensor prototype is constructed and demonstrated for single point pressure sensing at high temperature (600°C), with temperature compensation achieved through co-location of an SMS-IFPI temperature sensor. The inline geometry and low transmission loss of the SMS-IFPI sensor makes it suitable for frequency division multiplexing (FDM) in a single fiber branch. In future work, we envision multiplexing of up to eight such IFPI pressure sensors along a single fiber branch for quasi-distributed pressure measurement.


  • Open Access

    OPTICAL FIBER SENSOR TECHNOLOGIES FOR EFFICIENT AND ECONOMICAL OIL RECOVERY

    by Kristie Cooper, Gary Pickrell, Anbo Wang

    This report summarizes technical progress over the fourth year of the ''Optical Fiber Sensor Technologies for Efficient and Economical Oil Recovery'' program, funded by the Federal Energy Technology Center of the U.S. Department of Energy, and performed by the Center for Photonics Technology of the Bradley Department of Electrical and Computer Engineering at Virginia Tech. During the reporting period, research efforts under the program were focused on the development and evaluation of the fiber optic flow sensor system, and field testing in Tulsa, OK and the second field test of the pressure and temperature sensors in Coalinga, CA. The feasibility of a self-compensating fiber optic flow sensor based on a cantilever beam and interferometer for real-time flow rate measurements in the fluid filled pipes of oil field was clearly demonstrated. In addition, field testing of the pressure and temperature sensors deployed downhole continued. These accomplishments are summarized here: (1) Theoretical analysis and simulations were performed to ensure performance of the design. (2) The sensor fabrication and packaging techniques were investigated and improved. (3) Prototype flow sensors were fabricated based on the fabrication experience of hundreds of test sensors. (4) A lab-scale flow testing system was constructed and used for sensormore » evaluation. (5) Field-testing was performed in both the indoor and outdoor flow testing facility at the University of Tulsa, OK. (6) Testing of a multimode white light pressure and temperature sensor system continued at the oil site of Chevron/Texaco Company (Coalinga CA). « less

  • Self-calibrated interferometric/intensity-based (SCIIB) optical fiber pressure sensor

    by Jun Wang, Hai Xiao, Jiangdong Deng, Russell G. May, Anbo Wang

    A novel self-calibrated interferometer/industry-based (SCIIB) fiber optic sensor is described in this paper. The novel sensing scheme combines the advantages of both fiber interferometry senors and intensity-based sensors. The sensor operates on a single fiber Fabry-Perot interferometric cavity with a white light source. The interference signal of the sensor is coherent-sliced into two channels. Which allow fully real-time compensation for the source power drifting and fiber los variation. Temperature and pressure sensors with various dynamic ranges were designed and fabricated based on the SCIIB technology. Experimental result show that the SCIIB sensor scheme achieves excellent resolution and accuracy with the self- calibration function.


  • Two-mode elliptical-core fiber sensors for measurement of strain and temperature

    by Anbo Wang, Zhiguang Wang, Ashish M Vengsarkar, R Claus

    Properties of a two-mode, elliptical-core (e-core) fiber sensor and (i) a bimetallic strip or (ii) refractive- index changes in a liquid-filled hollow-core fiber. The output from a conventional two-mode, e-core fiber sensor is (i) projected upon a multimode fiber attached to a bimetallic strip or (ii) projected from an angular endface on a multimode fiber. The multimode fiber acts as a spatial filter and picks up part of the two-lobe pattern incident upon its core. A measurement of the differential phase variation gives an indication of the strain. The modulation depth of the output signal is shown to be a faithful indication of the temperature in both cases. Strain sensitivities typical of two-mode fiber sensors (0.033 degree(s) phase shift per microsecond(s) train-cm, minimum detectable strains of 0.17 micrometers /m for one meter sensing length) have been obtained with a temperature compensation accuracy of +/- 1 degree(s)C over a 75 degree(s)C range.