Mallory Parker
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mallory Parker has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Eleftheria Roumeli
University of Washington
3 shared publications - Andrew Matthew Jimenez
Materials Science and Engineering Department University of Washington Seattle Washington USA
1 shared publication - Anuscheh Nawaz1 shared publication
Bichlien Nguyen
Microsoft Corporation 1 Microsoft Way Redmond, WA 98052 USA
1 shared publication- Brandon Lou
Department of Materials Science and Engineering, University of Washington, Box 352120, Seattle, WA, USA 98195-21120
1 shared publication - David C. Burnett
Department of Electrical and Computer Engineering, Portland State University, Portland, OR, USA
1 shared publication
Latest Publications
- Open Access
- 30 May 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 37, 231-241
A novel filament design for improving fused filament fabrication of continuous fiber composites
- 30 May 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 37, 231-241
Open AccessA novel filament design for improving fused filament fabrication of continuous fiber composites
- 1 February 2025
- Published by BioResources in BioResources
- Vol. 20 (2)
Effects of pyrolysis temperature of macroalgal biomass on the structure and mechanical properties of produced biochar
Biochars, produced via pyrolysis, are gaining attention in applications ranging from soil amendments to energy storage and environmental remediation. While lignocellulosic biochars from woody biomass are well studied, algal biochars remain comparatively overlooked despite offering diverse organic and inorganic content that may broaden their applications. This study investigates how pyrolysis temperature and oxidative pretreatment affect the structure and properties of biochars derived from two macroalgae, Ulva expansa and Sargassum sp., under various pyrolysis conditions (500 to 900 °C). Using Raman spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, scanning electron microscopy, and nanoindentation, it was found that the C-O and C-N surface functional groups decreased in Ulva but the C=O and C-O-C groups increased in Sargassum upon pyrolysis. The reduced modulus ranged between 2.6 to 7.9 GPa and was governed by pyrolytic carbon content and inorganic composition. Of these two factors, the amount and type of pyrolytic carbon were determined by the heating conditions, with oxidation at 200 °C generally preserving more carbon than oxidation at 300 °C. Meanwhile, the final pyrolysis temperature dictated residual carbon content, salt formation, and carbonation. These findings highlight the potential for tailored pyrolysis to produce algal biochars with customizable structures and properties, enabling environmental and industrial applications such as carbon sequestration, filtration, and energy storage.
- 1 February 2025
- Published by BioResources in BioResources
- Vol. 20 (2)
Effects of pyrolysis temperature of macroalgal biomass on the structure and mechanical properties of produced biochar
Biochars, produced via pyrolysis, are gaining attention in applications ranging from soil amendments to energy storage and environmental remediation. While lignocellulosic biochars from woody biomass are well studied, algal biochars remain comparatively overlooked despite offering diverse organic and inorganic content that may broaden their applications. This study investigates how pyrolysis temperature and oxidative pretreatment affect the structure and properties of biochars derived from two macroalgae, Ulva expansa and Sargassum sp., under various pyrolysis conditions (500 to 900 °C). Using Raman spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, scanning electron microscopy, and nanoindentation, it was found that the C-O and C-N surface functional groups decreased in Ulva but the C=O and C-O-C groups increased in Sargassum upon pyrolysis. The reduced modulus ranged between 2.6 to 7.9 GPa and was governed by pyrolytic carbon content and inorganic composition. Of these two factors, the amount and type of pyrolytic carbon were determined by the heating conditions, with oxidation at 200 °C generally preserving more carbon than oxidation at 300 °C. Meanwhile, the final pyrolysis temperature dictated residual carbon content, salt formation, and carbonation. These findings highlight the potential for tailored pyrolysis to produce algal biochars with customizable structures and properties, enabling environmental and industrial applications such as carbon sequestration, filtration, and energy storage.
- 24 January 2025
- Published by Marine Technology Society in Marine Technology Society Journal
- Vol. 59 (1) , 36-50
Ecobuoys for Scalable Oceanography
An approach to scalable surface-drifting buoys is needed to enable the high spatial and temporal resolution of oceanographic data that the science and meteorological communities are asking for. With the number of active buoys predicted to increase by a factor of 100 or more, the impact on the environment becomes even more important. Here, we present a pathway to a scalable and sustainable generation of buoys. We identify the main criteria to be used when developing such buoys to be low cost, with reliable data and neutral or even positive environmental impact. For each buoy subsystem—hull, electronics, energy generation and storage, sensors, and communication system—cutting-edge technological solutions are presented, many of them from emerging research in marine or other disciplines. We then assess the potential solutions against the design criteria and plot a path toward small, environmentally friendly, low-cost, and low-power buoys.
- 24 January 2025
- Published by Marine Technology Society in Marine Technology Society Journal
- Vol. 59 (1) , 36-50
Ecobuoys for Scalable Oceanography
An approach to scalable surface-drifting buoys is needed to enable the high spatial and temporal resolution of oceanographic data that the science and meteorological communities are asking for. With the number of active buoys predicted to increase by a factor of 100 or more, the impact on the environment becomes even more important. Here, we present a pathway to a scalable and sustainable generation of buoys. We identify the main criteria to be used when developing such buoys to be low cost, with reliable data and neutral or even positive environmental impact. For each buoy subsystem—hull, electronics, energy generation and storage, sensors, and communication system—cutting-edge technological solutions are presented, many of them from emerging research in marine or other disciplines. We then assess the potential solutions against the design criteria and plot a path toward small, environmentally friendly, low-cost, and low-power buoys.
- 20 June 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (40)
Fabricating Strong and Stiff Bioplastics from Whole Spirulina Cells
Since the 1950s, 8.3 billion tonnes (Bt) of virgin plastics have been produced, of which around 5 Bt have accumulated as waste in oceans and other natural environments, posing severe threats to entire ecosystems. The need for sustainable bio‐based alternatives to traditional petroleum‐derived plastics is evident. Bioplastics produced from unprocessed biological materials have thus far suffered from heterogeneous and non‐cohesive morphologies, which lead to weak mechanical properties and lack of processability, hindering their industrial integration. Here, a fast, simple, and scalable process is presented to transform raw microalgae into a self‐bonded, recyclable, and backyard‐compostable bioplastic with attractive mechanical properties surpassing those of other biobased plastics such as thermoplastic starch. Upon hot‐pressing, the abundant and photosynthetic algae spirulina forms cohesive bioplastics with flexural modulus and strength in the range 3–5 GPa and 25.5–57 MPa, respectively, depending on pre‐processing conditions and the addition of nanofillers. The machinability of these bioplastics, along with self‐extinguishing properties, make them promising candidates for consumer plastics. Mechanical recycling and fast biodegradation in soil are demonstrated as end‐of‐life options. Finally, the environmental impacts are discussed in terms of global warming potential, highlighting the benefits of using a carbon‐negative feedstock such as spirulina to fabricate plastics.
- 20 June 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (40)
Fabricating Strong and Stiff Bioplastics from Whole Spirulina Cells
Since the 1950s, 8.3 billion tonnes (Bt) of virgin plastics have been produced, of which around 5 Bt have accumulated as waste in oceans and other natural environments, posing severe threats to entire ecosystems. The need for sustainable bio‐based alternatives to traditional petroleum‐derived plastics is evident. Bioplastics produced from unprocessed biological materials have thus far suffered from heterogeneous and non‐cohesive morphologies, which lead to weak mechanical properties and lack of processability, hindering their industrial integration. Here, a fast, simple, and scalable process is presented to transform raw microalgae into a self‐bonded, recyclable, and backyard‐compostable bioplastic with attractive mechanical properties surpassing those of other biobased plastics such as thermoplastic starch. Upon hot‐pressing, the abundant and photosynthetic algae spirulina forms cohesive bioplastics with flexural modulus and strength in the range 3–5 GPa and 25.5–57 MPa, respectively, depending on pre‐processing conditions and the addition of nanofillers. The machinability of these bioplastics, along with self‐extinguishing properties, make them promising candidates for consumer plastics. Mechanical recycling and fast biodegradation in soil are demonstrated as end‐of‐life options. Finally, the environmental impacts are discussed in terms of global warming potential, highlighting the benefits of using a carbon‐negative feedstock such as spirulina to fabricate plastics.