Yanzhou Jin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yanzhou Jin has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Yaonan Zhu
School of Engineering, The University of Tokyo, Tokyo, Japan
2 shared publications - Yusuke Iwasawa
The University of Tokyo
2 shared publications Adam J. Spiers
Department of Electrical and Electronic Engineering Imperial College London London UK
1 shared publication- Chang Li
State Key Laboratory of Intelligent Vehicle Safety Technology, Chongqing, China
1 shared publication - Chang Liu
The University of Tokyo
1 shared publication - Fei Suo
The University of Tokyo
1 shared publication
Latest Publications
- Open Access
- 16 September 2026
- Published by Wiley in Advanced Intelligent Systems
- p. e70542
Reinforcement Learning With a Low‐Cost Parallel Linkage Gripper for Static and Dynamic Planar In‐Hand Manipulation
Parallel linkage grippers provide a low‐cost and compact alternative to anthropomorphic hands for planar manipulation tasks. However, their closed‐chain kinematics introduce actuator coupling, singularity‐related constraints, and position‐dependent manipulation capability, making closed‐loop control challenging. This work presents D‐PALI‐E (Dual PArallel LInkage Enhanced), an open‐source, predominantly 3D‐printed parallel linkage gripper developed through hardware‐learning co‐design and equipped with passive‐joint limiters inspired by the overextension‐limiting function of the human finger volar plate. During contact, the limiters serve as motion constraints and part of the load‐bearing structure, modifying the gripper’s mechanical operating characteristics. They exclude mechanically undesirable configurations, participate in load transmission during pinch grasping, and reshape the operating region for policy learning. Reinforcement learning is used for quasi‐static pose adjustment (reorientation, repositioning, and full pose rearrangement) and dynamic pinch grasping (catching rolling balls of various sizes and directions and capturing slow or stationary objects). Sim‐to‐real transfer is achieved using system identification and domain randomization. Experiments demonstrate pose adjustment for regular geometric objects (within 5 mm and 5°), and a 72.5% average success rate in pinch grasping of rolling balls. These results show that the combined mechanical redesign and learning framework support both quasi‐static planar pose adjustment and dynamic pinch grasping on low‐cost hardware.
- 16 September 2026
- Published by Wiley in Advanced Intelligent Systems
- p. e70542
Open AccessReinforcement Learning With a Low‐Cost Parallel Linkage Gripper for Static and Dynamic Planar In‐Hand Manipulation
Parallel linkage grippers provide a low‐cost and compact alternative to anthropomorphic hands for planar manipulation tasks. However, their closed‐chain kinematics introduce actuator coupling, singularity‐related constraints, and position‐dependent manipulation capability, making closed‐loop control challenging. This work presents D‐PALI‐E (Dual PArallel LInkage Enhanced), an open‐source, predominantly 3D‐printed parallel linkage gripper developed through hardware‐learning co‐design and equipped with passive‐joint limiters inspired by the overextension‐limiting function of the human finger volar plate. During contact, the limiters serve as motion constraints and part of the load‐bearing structure, modifying the gripper’s mechanical operating characteristics. They exclude mechanically undesirable configurations, participate in load transmission during pinch grasping, and reshape the operating region for policy learning. Reinforcement learning is used for quasi‐static pose adjustment (reorientation, repositioning, and full pose rearrangement) and dynamic pinch grasping (catching rolling balls of various sizes and directions and capturing slow or stationary objects). Sim‐to‐real transfer is achieved using system identification and domain randomization. Experiments demonstrate pose adjustment for regular geometric objects (within 5 mm and 5°), and a 72.5% average success rate in pinch grasping of rolling balls. These results show that the combined mechanical redesign and learning framework support both quasi‐static planar pose adjustment and dynamic pinch grasping on low‐cost hardware.
- 27 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 8 (8) , 4673-4680
Design and Optimization of a Miniature Locust-Inspired Stable Jumping Robot
Jumping is a key locomotion for miniature robots, but it is difficult for a robot to jump a long distance without flipping. To solve this problem, we develop a miniature locust-inspired jumping robot, which has a body length of 10 cm and weight of 60 g. On the basis of the extracted skeletal muscle movement of a locust, we make full use of the Stephenson six-bar mechanism in designing a jumping leg to achieve power amplification. Moreover, we carry out a two-step optimization of the mechanism parameters to achieve high jumping energy (first step) through optimizing the storage and dissipation of energy and then high jumping stability (second step) through optimizing the force characteristics. A series of experimental tests show that the robot can jump to a height three times its body length and a distance seven times its body length. Remarkably, the jumping height and distance relative to the body length of our jumper exceeds that of other robots with stable mechanisms by 30% and 33%, respectively. Meanwhile, our robot has a high degree of stability, which allows it to maintain a proper aerial orientation without flipping.
- 27 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 8 (8) , 4673-4680
Design and Optimization of a Miniature Locust-Inspired Stable Jumping Robot
Jumping is a key locomotion for miniature robots, but it is difficult for a robot to jump a long distance without flipping. To solve this problem, we develop a miniature locust-inspired jumping robot, which has a body length of 10 cm and weight of 60 g. On the basis of the extracted skeletal muscle movement of a locust, we make full use of the Stephenson six-bar mechanism in designing a jumping leg to achieve power amplification. Moreover, we carry out a two-step optimization of the mechanism parameters to achieve high jumping energy (first step) through optimizing the storage and dissipation of energy and then high jumping stability (second step) through optimizing the force characteristics. A series of experimental tests show that the robot can jump to a height three times its body length and a distance seven times its body length. Remarkably, the jumping height and distance relative to the body length of our jumper exceeds that of other robots with stable mechanisms by 30% and 33%, respectively. Meanwhile, our robot has a high degree of stability, which allows it to maintain a proper aerial orientation without flipping.