Rifat Hasan Rupom
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rifat Hasan Rupom has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Wonbong Choi
Department of Materials Science and Engineering University of North Texas Denton Texas USA
6 shared publications H. Felix Wu
Vehicle Technologies Office, U.S. Department of Energy, 1000 Independence Avenue Southwest, Washington, District of Columbia 20585, United States
2 shared publicationsNurul Islam
School of Aerospace & Mechanical Engineering
2 shared publicationsOliver Chyan
Department of Chemistry University of North Texas Denton Texas USA
2 shared publicationsRigoberto C. Advincula
Center for Nanophase Materials and Sciences
2 shared publications- Yijie Jiang
School of Aerospace and Mechanical Engineering, University of Oklahoma, Norman, USA
2 shared publications
Latest Publications
- Open Access
- 7 October 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (91) , e78824
Contact Engineering Toward High‐Performance MoS 2 Neuromorphic Devices
Two‐dimensional transition metal dichalcogenides (2D TMDs) offer atomically thin, phase‐tunable platforms to obtain energy‐efficient neuromorphic devices. However, high contact resistance severely limits device performance by narrowing the memory window, increasing power consumption, and compromising long‐term reliability. To address these challenges, semi‐metallic bismuth (Bi) is employed as a metal electrode. The Bi‐contact configuration shows significantly reduced contact resistance, arising from electron doping at the MoS 2 –Bi interface, as confirmed by systematic I–V characterization, Raman, and XPS analysis. After lithiation, the Bi‐contact MoS 2 device demonstrates pronounced synaptic performance enhancement, achieving enhanced linearity and symmetry in synaptic weight modulation along with a high I on /I off ratio. Such synaptic memory modulation is attributed to ion‐induced localized phase change in the MoS 2 structure. Moreover, our Bi‐contact device achieves nanosecond switching speed with ultra‐low power consumption of 5.4 fJ/µm per event, along with 97% pattern recognition accuracy, outperforming the performance of conventional metal contacts. Localized phase modulation driven by efficient Li‐ion migration in an ohmic contact MoS 2 enables high‐accuracy synaptic memory operation with ultra‐low power consumption, demonstrating the viability of this approach for neuromorphic computing applications.
- 7 October 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (91) , e78824
Open AccessContact Engineering Toward High‐Performance MoS 2 Neuromorphic Devices
Two‐dimensional transition metal dichalcogenides (2D TMDs) offer atomically thin, phase‐tunable platforms to obtain energy‐efficient neuromorphic devices. However, high contact resistance severely limits device performance by narrowing the memory window, increasing power consumption, and compromising long‐term reliability. To address these challenges, semi‐metallic bismuth (Bi) is employed as a metal electrode. The Bi‐contact configuration shows significantly reduced contact resistance, arising from electron doping at the MoS 2 –Bi interface, as confirmed by systematic I–V characterization, Raman, and XPS analysis. After lithiation, the Bi‐contact MoS 2 device demonstrates pronounced synaptic performance enhancement, achieving enhanced linearity and symmetry in synaptic weight modulation along with a high I on /I off ratio. Such synaptic memory modulation is attributed to ion‐induced localized phase change in the MoS 2 structure. Moreover, our Bi‐contact device achieves nanosecond switching speed with ultra‐low power consumption of 5.4 fJ/µm per event, along with 97% pattern recognition accuracy, outperforming the performance of conventional metal contacts. Localized phase modulation driven by efficient Li‐ion migration in an ohmic contact MoS 2 enables high‐accuracy synaptic memory operation with ultra‐low power consumption, demonstrating the viability of this approach for neuromorphic computing applications.
- 27 April 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (20) , 28708-28716
Zn–CO 2 Batteries with 2D MoS 2 Catalysts for Sustainable Energy Storage
The rising levels of atmospheric CO2 demand urgent action toward carbon-neutral energy solutions. Metal–CO2 batteries uniquely combine the CO2 reduction (CO2RR) with energy storage, enabling the dual function of carbon capture and electricity generation within a single system. Among these, Zn–CO2 batteries stand out due to the abundance, low cost, safety, and environmental compatibility of zinc. This work presents a novel Zn–CO2 battery architecture that enables spontaneous electrochemical discharge in an aqueous NaCl electrolyte, eliminating the need for complex and high-cost components. It employs two-dimensional (2D) MoS2 as a bifunctional electrocatalyst to facilitate the CO2RR and battery rechargeability. The MoS2@carbon cathode exhibited a superior discharge capacity of approximately 50% higher than the bare carbon cathode and a lower overpotential (0.25 V), delivering a notably high energy density of ∼1200 Wh kg–1 based on the total mass of the cathode. Unlike conventional Zn–CO2 systems restricted to nonaqueous media, this design achieves stable cycling under ambient conditions through reversible Zn carbonate chemistry, while MoS2 catalysis lowers overpotential and boosts capacity and durability, yielding a highly efficient, cost-effective platform for carbon-neutral energy storage.
- 27 April 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (20) , 28708-28716
Zn–CO 2 Batteries with 2D MoS 2 Catalysts for Sustainable Energy Storage
The rising levels of atmospheric CO2 demand urgent action toward carbon-neutral energy solutions. Metal–CO2 batteries uniquely combine the CO2 reduction (CO2RR) with energy storage, enabling the dual function of carbon capture and electricity generation within a single system. Among these, Zn–CO2 batteries stand out due to the abundance, low cost, safety, and environmental compatibility of zinc. This work presents a novel Zn–CO2 battery architecture that enables spontaneous electrochemical discharge in an aqueous NaCl electrolyte, eliminating the need for complex and high-cost components. It employs two-dimensional (2D) MoS2 as a bifunctional electrocatalyst to facilitate the CO2RR and battery rechargeability. The MoS2@carbon cathode exhibited a superior discharge capacity of approximately 50% higher than the bare carbon cathode and a lower overpotential (0.25 V), delivering a notably high energy density of ∼1200 Wh kg–1 based on the total mass of the cathode. Unlike conventional Zn–CO2 systems restricted to nonaqueous media, this design achieves stable cycling under ambient conditions through reversible Zn carbonate chemistry, while MoS2 catalysis lowers overpotential and boosts capacity and durability, yielding a highly efficient, cost-effective platform for carbon-neutral energy storage.
- 3 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (24) , 36026-36033
Self-Sensing Composites via an Embedded 3D-Printed PVDF-MoS2 Nanosensor for Structural Health Monitoring
Carbon fiber (CF)-reinforced epoxy composites are widely used in vehicle applications, where early damage detection is crucial for reliability and safety. To address this need, we developed a self-sensing epoxy/CF composite by embedding a PVDF-MoS2 nanosensor via an embedded 3D printing method. By harnessing the intrinsic curing kinetics of epoxy, we tailored its rheological properties to optimize the embedded printing process, enabling precise and reliable support for sensor filaments without compromising the composite's structural and functional integrity. Through comprehensive rheological and kinetic analysis, we established a quantitative relationship among curing temperature, conversion rate, and resulting yield modulus─defining a narrow processing window essential for successful sensor integration. Specifically, we identified that an epoxy yield modulus range of 180-294 Pa and a conversion rate below 10% are critical to support the PVDF-MoS2 filament architecture. This embedded 3D printing method produces complex and multimaterial PVDF-MoS2 sensors within an epoxy matrix with minimal deformation and reduced postprocessing, which is scalable and adaptable for industrial applications. Under cyclic loading, the embedded sensors exhibited stable signals under constant loads and increased voltage signals in response to crack formation (17-35% higher) and catastrophic failure (1 order of magnitude higher), effectively capturing structural changes in real time. This study demonstrates the potential of PVDF-MoS2 nanocomposite sensor materials for real-time structural health monitoring in epoxy-CF composite systems, enabling early detection of defects and stress anomalies, significantly reducing the risk of unexpected failures, and enhancing structural reliability.
- 3 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (24) , 36026-36033
Self-Sensing Composites via an Embedded 3D-Printed PVDF-MoS2 Nanosensor for Structural Health Monitoring
Carbon fiber (CF)-reinforced epoxy composites are widely used in vehicle applications, where early damage detection is crucial for reliability and safety. To address this need, we developed a self-sensing epoxy/CF composite by embedding a PVDF-MoS2 nanosensor via an embedded 3D printing method. By harnessing the intrinsic curing kinetics of epoxy, we tailored its rheological properties to optimize the embedded printing process, enabling precise and reliable support for sensor filaments without compromising the composite's structural and functional integrity. Through comprehensive rheological and kinetic analysis, we established a quantitative relationship among curing temperature, conversion rate, and resulting yield modulus─defining a narrow processing window essential for successful sensor integration. Specifically, we identified that an epoxy yield modulus range of 180-294 Pa and a conversion rate below 10% are critical to support the PVDF-MoS2 filament architecture. This embedded 3D printing method produces complex and multimaterial PVDF-MoS2 sensors within an epoxy matrix with minimal deformation and reduced postprocessing, which is scalable and adaptable for industrial applications. Under cyclic loading, the embedded sensors exhibited stable signals under constant loads and increased voltage signals in response to crack formation (17-35% higher) and catastrophic failure (1 order of magnitude higher), effectively capturing structural changes in real time. This study demonstrates the potential of PVDF-MoS2 nanocomposite sensor materials for real-time structural health monitoring in epoxy-CF composite systems, enabling early detection of defects and stress anomalies, significantly reducing the risk of unexpected failures, and enhancing structural reliability.
- 6 January 2025
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 19 (2) , 2529-2539
Ion-Induced Phase Changes in 2D MoTe2 Films for Neuromorphic Synaptic Device Applications
Two-dimensional molybdenum ditelluride (2D MoTe2) is an interesting material for artificial synapses due to its unique electronic properties and phase tunability in different polymorphs 2H/1T'. However, the growth of stable and large-scale 2D MoTe2 on a CMOS-compatible Si/SiO2 substrate remains challenging because of the high growth temperature and impurity-involved transfer process. We developed a large-scale MoTe2 film on a Si/SiO2 wafer by simple sputtering followed by lithium-ion intercalation and applied it to artificial synaptic devices. The Al2O3 passivation layer allows us to develop a stable 1T'-MoTe2 phase by preventing Te segregation caused by the weak bonding between Mo and Te atoms during lithiation. The lithiated MoTe2 film exhibits excellent synaptic behavior such as long-term potentiation/depression, a high Ion/Ioff ratio (≈103) at lower sweep voltage, and long-term retention. The in situ Raman analysis along with a systematic microstructural analysis reveals that the intercalated Li ion can provide an efficient pathway for conducting filament formation.
- 6 January 2025
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 19 (2) , 2529-2539
Ion-Induced Phase Changes in 2D MoTe2 Films for Neuromorphic Synaptic Device Applications
Two-dimensional molybdenum ditelluride (2D MoTe2) is an interesting material for artificial synapses due to its unique electronic properties and phase tunability in different polymorphs 2H/1T'. However, the growth of stable and large-scale 2D MoTe2 on a CMOS-compatible Si/SiO2 substrate remains challenging because of the high growth temperature and impurity-involved transfer process. We developed a large-scale MoTe2 film on a Si/SiO2 wafer by simple sputtering followed by lithium-ion intercalation and applied it to artificial synaptic devices. The Al2O3 passivation layer allows us to develop a stable 1T'-MoTe2 phase by preventing Te segregation caused by the weak bonding between Mo and Te atoms during lithiation. The lithiated MoTe2 film exhibits excellent synaptic behavior such as long-term potentiation/depression, a high Ion/Ioff ratio (≈103) at lower sweep voltage, and long-term retention. The in situ Raman analysis along with a systematic microstructural analysis reveals that the intercalated Li ion can provide an efficient pathway for conducting filament formation.
- 19 September 2024
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 7 (19) , 22714-22722
Tailoring Piezoelectricity of 3D Printing PVDF-MoS2 Nanocomposite via In Situ Induced Shear Stress
- 19 September 2024
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 7 (19) , 22714-22722
Tailoring Piezoelectricity of 3D Printing PVDF-MoS2 Nanocomposite via In Situ Induced Shear Stress
- Top Cited PapersOpen Access
- 21 June 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (42)
Boosting Piezoelectricity by 3D Printing PVDF‐MoS2 Composite as a Conformal and High‐Sensitivity Piezoelectric Sensor
Additively manufactured flexible and high‐performance piezoelectric devices are highly desirable for sensing and energy harvesting of 3D conformal structures. Herein, the study reports a significantly enhanced piezoelectricity in polyvinylidene fluoride (PVDF) achieved through the in situ dipole alignment of PVDF within PVDF‐2D molybdenum disulfide (2D MoS2) composite by 3D printing. The shear stress‐induced dipole poling of PVDF and 2D MoS2 alignment are harnessed during 3D printing to boost piezoelectricity without requiring a post‐poling process. The results show a remarkable, more than the eight‐fold increment in the piezoelectric coefficient (d33) for 3D printed PVDF‐8wt.% MoS2 composite over cast neat PVDF. The underlying mechanism of piezoelectric property enhancement is attributed to the increased volume fraction of β phase in PVDF, filler fraction, heterogeneous strain distribution around PVDF‐MoS2 interfaces, and strain transfer to the nanofillers as confirmed by microstructural analysis and finite element simulation. These results provide a promising route to design and fabricate high‐performance 3D piezoelectric devices via 3D printing for next‐generation sensors and mechanical–electronic conformal devices.
- 21 June 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (42)
Top Cited PapersOpen AccessBoosting Piezoelectricity by 3D Printing PVDF‐MoS2 Composite as a Conformal and High‐Sensitivity Piezoelectric Sensor
Additively manufactured flexible and high‐performance piezoelectric devices are highly desirable for sensing and energy harvesting of 3D conformal structures. Herein, the study reports a significantly enhanced piezoelectricity in polyvinylidene fluoride (PVDF) achieved through the in situ dipole alignment of PVDF within PVDF‐2D molybdenum disulfide (2D MoS2) composite by 3D printing. The shear stress‐induced dipole poling of PVDF and 2D MoS2 alignment are harnessed during 3D printing to boost piezoelectricity without requiring a post‐poling process. The results show a remarkable, more than the eight‐fold increment in the piezoelectric coefficient (d33) for 3D printed PVDF‐8wt.% MoS2 composite over cast neat PVDF. The underlying mechanism of piezoelectric property enhancement is attributed to the increased volume fraction of β phase in PVDF, filler fraction, heterogeneous strain distribution around PVDF‐MoS2 interfaces, and strain transfer to the nanofillers as confirmed by microstructural analysis and finite element simulation. These results provide a promising route to design and fabricate high‐performance 3D piezoelectric devices via 3D printing for next‐generation sensors and mechanical–electronic conformal devices.