Alicia M. Polo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alicia M. Polo has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Angel Fernandez Mohedano
Chemical Engineering Department, Universidad Autonoma de Madrid, Campus de Cantoblanco, 28049 Madrid, Spain
10 shared publications - Juan Jose Rodriguez
Chemical Engineering Department, Universidad Autónoma de Madrid, 28049 Madrid, Spain
10 shared publications - Montserrat Tobajas
Universidad Autónoma de Madrid
7 shared publications A. Pardo
6 shared publicationsJ.J. Camacho
6 shared publicationsJ.M.L. Poyato
6 shared publications
Latest Publications
- 1 March 2019
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 365, 289-296
Removal of imidazolium-based ionic liquid by coupling Fenton and biological oxidation
- 1 March 2019
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 365, 289-296
Removal of imidazolium-based ionic liquid by coupling Fenton and biological oxidation
- 9 January 2018
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 25 (35) , 34930-34937
Removal of imidazolium- and pyridinium-based ionic liquids by Fenton oxidation
Abstract The oxidation of imidazolium (1-hexyl-3-methylimidazolium chloride, HmimCl) and pyridinium (1-butyl-4-methylpyridinium chloride, BmpyrCl) ionic liquids (ILs) by Fenton’s reagent has been studied. Complete conversion was achieved for both ILs using the stoichiometric H2O2 dose at 70 °C, reaching final TOC conversion values around 45 and 55% for HmimCl and BmpyrCl, respectively. The decrease in hydrogen peroxide dose to substoichiometric concentrations (20–80% stoichiometric dose) caused a decrease in TOC conversion and COD removal and the appearance of hydroxylated oxidation by-products. Working at these substoichiometric H2O2 doses allowed the depiction of a possible degradation pathway for the oxidation of both imidazolium and pyridinium ILs. The first step of the oxidation process consisted in the hydroxylation of the ionic liquid by the attack of the ·OH radicals, followed by the ring-opening and the formation of short-chain organic acids, which could be partially oxidized up to CO2 and H2O. At H2O2 doses near stoichiometric values (80%), the resulting effluents showed non-ecotoxic behaviour and more biodegradable character (BOD5/COD ratio around 0.38 and 0.58 for HmimCl and BmpyrCl, respectively) due to the formation of short-chain organic acids. ᅟ
- 9 January 2018
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 25 (35) , 34930-34937
Removal of imidazolium- and pyridinium-based ionic liquids by Fenton oxidation
Abstract The oxidation of imidazolium (1-hexyl-3-methylimidazolium chloride, HmimCl) and pyridinium (1-butyl-4-methylpyridinium chloride, BmpyrCl) ionic liquids (ILs) by Fenton’s reagent has been studied. Complete conversion was achieved for both ILs using the stoichiometric H2O2 dose at 70 °C, reaching final TOC conversion values around 45 and 55% for HmimCl and BmpyrCl, respectively. The decrease in hydrogen peroxide dose to substoichiometric concentrations (20–80% stoichiometric dose) caused a decrease in TOC conversion and COD removal and the appearance of hydroxylated oxidation by-products. Working at these substoichiometric H2O2 doses allowed the depiction of a possible degradation pathway for the oxidation of both imidazolium and pyridinium ILs. The first step of the oxidation process consisted in the hydroxylation of the ionic liquid by the attack of the ·OH radicals, followed by the ring-opening and the formation of short-chain organic acids, which could be partially oxidized up to CO2 and H2O. At H2O2 doses near stoichiometric values (80%), the resulting effluents showed non-ecotoxic behaviour and more biodegradable character (BOD5/COD ratio around 0.38 and 0.58 for HmimCl and BmpyrCl, respectively) due to the formation of short-chain organic acids. ᅟ
- 11 September 2015
- Published by Taylor & Francis in Environmental Technology
- Vol. 37 (6) , 713-721
Assessment of toxicity and biodegradability on activated sludge of priority and emerging pollutants
Several methods for evaluating the toxicity and biodegradability of hazardous pollutants (chlorinated compounds, chemical additives and pharmaceuticals) have been studied in this work. Different bioassays using representative bacteria of marine and terrestrial ecosystems such as Vibrio fischeri and Pseudomonas putida have been used to assess the ecotoxicity. Activated sludge was used to analyse the effect of those pollutants in a biological reactor of a sewage treatment plant (STP). The results demonstrate that none of the compounds is toxic to activated sludge, except ofloxacin to P. putida. The additives tested can be considered moderately toxic according to the more sensitive V. fischeri assays, whereas the EC50 values of the pharmaceuticals depend on the specific microorganism used in each test. Regarding the biodegradability, respirometric measurements were carried out for fast biodegradability assessment and the Zahn–Wellens test for inherent biodegradability. The evolution of the specific oxygen uptake rate (SOUR) showed that only diethyl phthalate was easily biodegradable and acetylsalicylic acid was partially biodegradable (98% and 65% degradation, respectively). The persistence of dichloromethane, ofloxacin and hidrochlorothiazide was confirmed along the 28 days of the Zahn-Wellens test whereas 1,1,1-trichloroethane showed inherent biodegradability (74% removal). Most of the chlorinated compounds, pharmaceuticals, bisphenol A and ethylenediaminetetraacetic acid were partially degraded in 28 d with total organic carbon (TOC) reduction ranging from 21% to 51%. Sulphamethoxazole showed certain biodegradation (50% removal) with TOC decrease around 31%, which indicates the formation of non-biodegradable by-products.
- 11 September 2015
- Published by Taylor & Francis in Environmental Technology
- Vol. 37 (6) , 713-721
Assessment of toxicity and biodegradability on activated sludge of priority and emerging pollutants
Several methods for evaluating the toxicity and biodegradability of hazardous pollutants (chlorinated compounds, chemical additives and pharmaceuticals) have been studied in this work. Different bioassays using representative bacteria of marine and terrestrial ecosystems such as Vibrio fischeri and Pseudomonas putida have been used to assess the ecotoxicity. Activated sludge was used to analyse the effect of those pollutants in a biological reactor of a sewage treatment plant (STP). The results demonstrate that none of the compounds is toxic to activated sludge, except ofloxacin to P. putida. The additives tested can be considered moderately toxic according to the more sensitive V. fischeri assays, whereas the EC50 values of the pharmaceuticals depend on the specific microorganism used in each test. Regarding the biodegradability, respirometric measurements were carried out for fast biodegradability assessment and the Zahn–Wellens test for inherent biodegradability. The evolution of the specific oxygen uptake rate (SOUR) showed that only diethyl phthalate was easily biodegradable and acetylsalicylic acid was partially biodegradable (98% and 65% degradation, respectively). The persistence of dichloromethane, ofloxacin and hidrochlorothiazide was confirmed along the 28 days of the Zahn-Wellens test whereas 1,1,1-trichloroethane showed inherent biodegradability (74% removal). Most of the chlorinated compounds, pharmaceuticals, bisphenol A and ethylenediaminetetraacetic acid were partially degraded in 28 d with total organic carbon (TOC) reduction ranging from 21% to 51%. Sulphamethoxazole showed certain biodegradation (50% removal) with TOC decrease around 31%, which indicates the formation of non-biodegradable by-products.
- 1 February 2014
- Published by Elsevier in Water Research
- Vol. 49, 197-206
Coupling Fenton and biological oxidation for the removal of nitrochlorinated herbicides from water
- 1 February 2014
- Published by Elsevier in Water Research
- Vol. 49, 197-206
Coupling Fenton and biological oxidation for the removal of nitrochlorinated herbicides from water
- 13 September 2013
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 21 (16) , 9445-9452
Strategies to evaluate biodegradability: application to chlorinated herbicides
The biodegradability of nitrochlorinated (diuron and atrazine) and chlorophenoxy herbicides (2,4-D and MCPA) has been studied through several bioassays using different testing times and biomass/substrate ratios. A fast biodegradability test using unacclimated activated sludge yielded no biodegradation of the herbicides in 24 h. The inherent biodegradability test gave degradation percentages of around 20–30 % for the nitrochlorinated herbicides and almost complete removal of the chlorophenoxy compounds. Long-term biodegradability assays were performed using sequencing batch reactor (SBR) and sequencing batch membrane bioreactor (SB-MBR). Fixed concentrations of each herbicide below the corresponding EC50 value for activated sludge were used (30 mg L−1 for diuron and atrazine and 50 mg L−1 for 2,4-D and MCPA). No signs of herbicide degradation appeared before 35 days in the case of diuron and atrazine and 21 days for 2,4-D, whereas MCPA was partially degraded since the early stages. Around 25–36 % degradation of the nitrochlorinated herbicides and 53–77 % of the chlorophenoxy ones was achieved after 180 and 135 days, respectively, in SBR, whereas complete disappearance of 2,4-D was reached after 80 days in SB-MBR.
- 13 September 2013
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 21 (16) , 9445-9452
Strategies to evaluate biodegradability: application to chlorinated herbicides
The biodegradability of nitrochlorinated (diuron and atrazine) and chlorophenoxy herbicides (2,4-D and MCPA) has been studied through several bioassays using different testing times and biomass/substrate ratios. A fast biodegradability test using unacclimated activated sludge yielded no biodegradation of the herbicides in 24 h. The inherent biodegradability test gave degradation percentages of around 20–30 % for the nitrochlorinated herbicides and almost complete removal of the chlorophenoxy compounds. Long-term biodegradability assays were performed using sequencing batch reactor (SBR) and sequencing batch membrane bioreactor (SB-MBR). Fixed concentrations of each herbicide below the corresponding EC50 value for activated sludge were used (30 mg L−1 for diuron and atrazine and 50 mg L−1 for 2,4-D and MCPA). No signs of herbicide degradation appeared before 35 days in the case of diuron and atrazine and 21 days for 2,4-D, whereas MCPA was partially degraded since the early stages. Around 25–36 % degradation of the nitrochlorinated herbicides and 53–77 % of the chlorophenoxy ones was achieved after 180 and 135 days, respectively, in SBR, whereas complete disappearance of 2,4-D was reached after 80 days in SB-MBR.
- 1 September 2013
- Published by Elsevier in Chemosphere
- Vol. 93 (1) , 115-122
Degradation of chlorophenoxy herbicides by coupled Fenton and biological oxidation
- 1 September 2013
- Published by Elsevier in Chemosphere
- Vol. 93 (1) , 115-122
Degradation of chlorophenoxy herbicides by coupled Fenton and biological oxidation
- 1 May 2013
- Published by Elsevier in Chemosphere
- Vol. 91 (9) , 1317-1323
Identification of by-products and toxicity assessment in aqueous-phase hydrodechlorination of diuron with palladium on activated carbon catalysts
- 1 May 2013
- Published by Elsevier in Chemosphere
- Vol. 91 (9) , 1317-1323
Identification of by-products and toxicity assessment in aqueous-phase hydrodechlorination of diuron with palladium on activated carbon catalysts
- 11 April 2012
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 87 (9) , 1263-1269
On the biodegradability of nitrophenols and their reaction products by catalytic hydrogenation*
BACKGROUND: Catalytic hydrogenation is gaining interest as an emerging technology for the detoxification of industrial effluents containing pollutants such as nitrophenols. This technique achieves high conversion levels under ambient‐like conditions of temperature and pressure, leading to less harmful products than the starting compounds.RESULTS: Complete conversion of 2‐nitrophenol, 4‐nitrophenol and 2,4‐dinitrophenol was achieved in short reaction times at 25 °C and 1 atm, using Pd/Al2O3 and Rh/Al2O3 catalysts. The rates of disappearance followed the sequence: 2,4‐dinitrophenol > 2‐nitrophenol > 4‐nitrophenol, the Pd catalyst being more active than the Rh one. The corresponding amino‐compounds were identified as the only reaction products. From a Microtox test the reaction products appeared more toxic than the starting compounds. Nevertheless, respirometric tests with conventional activated sludge yielded EC50 values for the aminophenols about double those of the nitrophenols. Biodegradability tests showed that the monoaminophenols can be degraded by non‐acclimated sludge, whereas no degradation was observed for the nitrophenols and 2‐amino‐4‐nitrophenol, the reaction product from 2,4‐dinitrophenol hydrogenation.CONCLUSION: Catalytic hydrogenation of wastewater containing nitrophenols gives rise to byproducts less toxic and more easily biodegradable by an activated sludge. Copyright © 2012 Society of Chemical Industry
- 11 April 2012
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 87 (9) , 1263-1269
On the biodegradability of nitrophenols and their reaction products by catalytic hydrogenation*
BACKGROUND: Catalytic hydrogenation is gaining interest as an emerging technology for the detoxification of industrial effluents containing pollutants such as nitrophenols. This technique achieves high conversion levels under ambient‐like conditions of temperature and pressure, leading to less harmful products than the starting compounds.RESULTS: Complete conversion of 2‐nitrophenol, 4‐nitrophenol and 2,4‐dinitrophenol was achieved in short reaction times at 25 °C and 1 atm, using Pd/Al2O3 and Rh/Al2O3 catalysts. The rates of disappearance followed the sequence: 2,4‐dinitrophenol > 2‐nitrophenol > 4‐nitrophenol, the Pd catalyst being more active than the Rh one. The corresponding amino‐compounds were identified as the only reaction products. From a Microtox test the reaction products appeared more toxic than the starting compounds. Nevertheless, respirometric tests with conventional activated sludge yielded EC50 values for the aminophenols about double those of the nitrophenols. Biodegradability tests showed that the monoaminophenols can be degraded by non‐acclimated sludge, whereas no degradation was observed for the nitrophenols and 2‐amino‐4‐nitrophenol, the reaction product from 2,4‐dinitrophenol hydrogenation.CONCLUSION: Catalytic hydrogenation of wastewater containing nitrophenols gives rise to byproducts less toxic and more easily biodegradable by an activated sludge. Copyright © 2012 Society of Chemical Industry
- 15 February 2011
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 50 (6) , 3452-3463
Understanding the Physical Absorption of CO2 in Ionic Liquids Using the COSMO-RS Method
- 15 February 2011
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 50 (6) , 3452-3463
Understanding the Physical Absorption of CO2 in Ionic Liquids Using the COSMO-RS Method
- 9 January 2011
- Published by Springer Nature in Biodegradation
- Vol. 22 (4) , 751-761
Comparison of experimental methods for determination of toxicity and biodegradability of xenobiotic compounds
Different methods for determining the toxicity and biodegradability of hazardous compounds evaluating their susceptibility to biological treatment were studied. Several compounds including chlorophenols and herbicides have been evaluated. Toxicity was analyzed in terms of EC50 and by a simple respirometric procedure based on the OECD Method 209 and by the Microtox® bioassay. The values of EC50 obtained from respirometry were in all the cases higher than those from the Microtox® test. The respirometric inhibition values of chlorophenols were related well with the number of chlorine atoms and their position in the aromatic ring. In general, herbicides showed lower inhibition, being alachlor the less toxic from this criterion. For determination of biodegradability an easier and faster alternative to the OECD Method 301, with a higher biomass to substrate ratio is proposed. When this test was negative, the Zahn-Wellens one was performed in order to evaluate the inherent biodegradability. In the fast test of biodegradability, 4-chlorocatechol and 4-chlorophenol showed a complete biodegradation by an unacclimated sludge upon 48 h. These results together with their low respirometric inhibition, allow concluding that these compounds could be conveniently removed in a WWTP. Alachlor, 2,4-dichlorophenol, 2,4,6-trichlorophenol and MCPA showed a partial biodegradation upon 28 days by the Zahn-Wellens inherent biodegradability test.
- 9 January 2011
- Published by Springer Nature in Biodegradation
- Vol. 22 (4) , 751-761
Comparison of experimental methods for determination of toxicity and biodegradability of xenobiotic compounds
Different methods for determining the toxicity and biodegradability of hazardous compounds evaluating their susceptibility to biological treatment were studied. Several compounds including chlorophenols and herbicides have been evaluated. Toxicity was analyzed in terms of EC50 and by a simple respirometric procedure based on the OECD Method 209 and by the Microtox® bioassay. The values of EC50 obtained from respirometry were in all the cases higher than those from the Microtox® test. The respirometric inhibition values of chlorophenols were related well with the number of chlorine atoms and their position in the aromatic ring. In general, herbicides showed lower inhibition, being alachlor the less toxic from this criterion. For determination of biodegradability an easier and faster alternative to the OECD Method 301, with a higher biomass to substrate ratio is proposed. When this test was negative, the Zahn-Wellens one was performed in order to evaluate the inherent biodegradability. In the fast test of biodegradability, 4-chlorocatechol and 4-chlorophenol showed a complete biodegradation by an unacclimated sludge upon 48 h. These results together with their low respirometric inhibition, allow concluding that these compounds could be conveniently removed in a WWTP. Alachlor, 2,4-dichlorophenol, 2,4,6-trichlorophenol and MCPA showed a partial biodegradation upon 28 days by the Zahn-Wellens inherent biodegradability test.