Hao Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hao Chen has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Yiqiang Pei
Tianjin University, Tianjin 300072, China
2 shared publications - Zhihao Ma
School of Vehicle and Traffic Engineering, Henan University of Science and Technology, Luoyang 471003, China
2 shared publications - Chenxi Wang
State Key Laboratory of Engines, Tianjin University, Tianjin 300072, China
1 shared publication - Kai Zhao
CATARC Automotive Test Center (Changzhou) Co., Ltd., Changzhou 213164, China
1 shared publication - Linlei Luo
College of Vehicle and Traffic Engineering, Henan University of Science and Technology, Luoyang 471003, China
1 shared publication - Miao Zhang
Tsinghua University
1 shared publication
Latest Publications
- Open Access
- 4 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (23) , 11317
A Numerical Simulation of Mixture Formation in a Hydrogen Direct-Injection Internal Combustion Engine
Direct-injection technology applied in hydrogen internal combustion engines can effectively prevent backfire, thereby improving the engine performance. Nonetheless, optimizing the injection strategy is highly intricate, requiring a comprehensive understanding of the hydrogen–air mixture formation process inside the cylinder. In this study, a simulation of hydrogen–air mixture formation was systematically conducted in a hydrogen direct-injection internal combustion engine using three-dimensional computational fluid dynamics (CFD) software. Under rated conditions, the influence of the nozzle hole number, injection direction, injection timing, and combustion chamber geometry on the mixture formation was analyzed from the perspectives of flow state and mass transfer. The results indicate that more nozzle holes would lead to more significant non-uniformity of the mixture, mainly due to the Coanda effect. The normalized standard deviation (NSD) of a six-hole nozzle design is 0.3495, which is higher than the NSD of all the single-hole nozzle conditions. By changing the hydrogen injection timing from −144 °CA to −136 °CA, the non-uniformity coefficient of the mixture is little affected, while notable differences in the distribution of the mixture are observed. The appropriate injection directions and optimized combustion chamber geometries could also help to effectively organize the in-cylinder flow, significantly improving the uniformity of the in-cylinder mixture and reducing the likelihood of abnormal combustion events.
- 4 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (23) , 11317
Open AccessA Numerical Simulation of Mixture Formation in a Hydrogen Direct-Injection Internal Combustion Engine
Direct-injection technology applied in hydrogen internal combustion engines can effectively prevent backfire, thereby improving the engine performance. Nonetheless, optimizing the injection strategy is highly intricate, requiring a comprehensive understanding of the hydrogen–air mixture formation process inside the cylinder. In this study, a simulation of hydrogen–air mixture formation was systematically conducted in a hydrogen direct-injection internal combustion engine using three-dimensional computational fluid dynamics (CFD) software. Under rated conditions, the influence of the nozzle hole number, injection direction, injection timing, and combustion chamber geometry on the mixture formation was analyzed from the perspectives of flow state and mass transfer. The results indicate that more nozzle holes would lead to more significant non-uniformity of the mixture, mainly due to the Coanda effect. The normalized standard deviation (NSD) of a six-hole nozzle design is 0.3495, which is higher than the NSD of all the single-hole nozzle conditions. By changing the hydrogen injection timing from −144 °CA to −136 °CA, the non-uniformity coefficient of the mixture is little affected, while notable differences in the distribution of the mixture are observed. The appropriate injection directions and optimized combustion chamber geometries could also help to effectively organize the in-cylinder flow, significantly improving the uniformity of the in-cylinder mixture and reducing the likelihood of abnormal combustion events.
- Open Access
- 29 June 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (13) , 10290
Quantitative Analysis of Water Injection Mass and Timing Effects on Oxy-Fuel Combustion Characteristics in a GDI Engine Fuelled with E10
The climate change issue has become a growing concern due to the increasing greenhouse gas emissions. To achieve carbon neutrality for mitigating the climate problem, the oxy-fuel combustion (OFC) technique on internal combustion engines (ICEs) has attracted much attention. Furthermore, the water injection (WI) strategy was proven effective in improving the combustion process and thermal efficiency in engines under OFC mode. However, WI strategy effects on gasoline direct injection (GDI) engines fuelled with gasoline–alcohol blends have not been reported. This study quantitatively analysed WI mass and timing effects on oxy-fuel combustion performance from a GDI engine fuelled with E10 (10% ethanol and 90% gasoline in mass) by simulation. The results show that equivalent brake-specific fuel consumption (BSFCE) shows a monotonically decreasing trend with the increase in the water–fuel mass ratio () from 0 to 0.2. However, further increasing would cause a deterioration in BSFCE due to the enhanced cooling effects of water vaporisation. Moreover, an appropriate water injection timing () could be explored for improving OFC performance, especially for large conditions. The difference in BSFCE between = −100°CA and = −60°CA can be up to around 6.3 g/kWh by increasing to 0.6.- 29 June 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (13) , 10290
Open AccessQuantitative Analysis of Water Injection Mass and Timing Effects on Oxy-Fuel Combustion Characteristics in a GDI Engine Fuelled with E10
The climate change issue has become a growing concern due to the increasing greenhouse gas emissions. To achieve carbon neutrality for mitigating the climate problem, the oxy-fuel combustion (OFC) technique on internal combustion engines (ICEs) has attracted much attention. Furthermore, the water injection (WI) strategy was proven effective in improving the combustion process and thermal efficiency in engines under OFC mode. However, WI strategy effects on gasoline direct injection (GDI) engines fuelled with gasoline–alcohol blends have not been reported. This study quantitatively analysed WI mass and timing effects on oxy-fuel combustion performance from a GDI engine fuelled with E10 (10% ethanol and 90% gasoline in mass) by simulation. The results show that equivalent brake-specific fuel consumption (BSFCE) shows a monotonically decreasing trend with the increase in the water–fuel mass ratio () from 0 to 0.2. However, further increasing would cause a deterioration in BSFCE due to the enhanced cooling effects of water vaporisation. Moreover, an appropriate water injection timing () could be explored for improving OFC performance, especially for large conditions. The difference in BSFCE between = −100°CA and = −60°CA can be up to around 6.3 g/kWh by increasing to 0.6.