Toshiro Sato
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Toshiro Sato has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Makoto Sonehara
Shinshu University
4 shared publications - Akekachai Pannawan
School of Renewable Energy and Smart Grid Technology (SGtech), Naresuan University, Phitsanulok 65000, Thailand
1 shared publication - Fu Namai
Food and Feed Immunology Group, Laboratory of Animal Food Function, Graduate School of Agricultural Science, Tohoku University, Sendai 980-8572, Japan
1 shared publication Hideharu Otsu
Department of Physics , Nagoya University , Nagoya, 464-01, Japan
1 shared publication- Hideki Oyama
Ajinomoto Fine-Techno Company Inc., Kawasaki, Japan
1 shared publication - Hiroshi Komatsu
Department of Psychiatry, Tohoku University Hospital, Miyagi, Japan
1 shared publication
Latest Publications
- 5 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-6
Development of an Optical Probe Current Sensor for Local and Narrow Area Measurement Using Magnetic Domain Reversal in Bismuth-Substituted Rare-Earth Iron Garnet Crystal
The authors have developed an optical probe electric current sensor using a Faraday effect of granular magnetic film as a new current sensor to replace a current transformer and a Rogowski coil. However, the sensitivity for small current fields in the previously developed sensor was low, and the signal was buried in the floor noise, making accurate measurement impossible. In this study, we investigated a sensor using magnetic domain reversal of Bi:RIG crystal for Faraday element to solve the previous problem and succeeded in developing a sensor with excellent linearity and a high signal-to-noise ratio by optimizing the Bi:RIG crystal thickness and the light-beam diameter to be irradiated.
- 5 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-6
Development of an Optical Probe Current Sensor for Local and Narrow Area Measurement Using Magnetic Domain Reversal in Bismuth-Substituted Rare-Earth Iron Garnet Crystal
The authors have developed an optical probe electric current sensor using a Faraday effect of granular magnetic film as a new current sensor to replace a current transformer and a Rogowski coil. However, the sensitivity for small current fields in the previously developed sensor was low, and the signal was buried in the floor noise, making accurate measurement impossible. In this study, we investigated a sensor using magnetic domain reversal of Bi:RIG crystal for Faraday element to solve the previous problem and succeeded in developing a sensor with excellent linearity and a high signal-to-noise ratio by optimizing the Bi:RIG crystal thickness and the light-beam diameter to be irradiated.
- 30 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-5
Magnetic Properties of Soft Magnetic Powder/Epoxy Composite Sheet
This paper describes the development of a composite resin magnetic sheet of soft magnetic powder and epoxy resin used in the beyond 10MHz band magnetic devices. Magnetic powder and epoxy resin were mixed, dispersed and formed into a sheet shape by the bar coating method. Fe-Si based polycrystalline fine powder, Fe-Si-Cr based amorphous fine powder and Fe-Si-Nb-Cu-B based nanocrystalline fine powder with an average particle were used as the starting soft magnetic powder. In addition, submicron Fe-Si-Cr based powder was used to further increase the packing density of the magnetic powder in the composite sheet. As the evaluation of the magnetic sheet, saturation magnetization, coercivity, relative magnetic permeability and loss-tangent in 10MHz - hundreds MHz were measured. A magnetic sheet using the nanocrystalline powder and submicron powder showed high relative permeability of 13 and low loss-tangent of 0.05 at 100MHz.
- 30 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-5
Magnetic Properties of Soft Magnetic Powder/Epoxy Composite Sheet
This paper describes the development of a composite resin magnetic sheet of soft magnetic powder and epoxy resin used in the beyond 10MHz band magnetic devices. Magnetic powder and epoxy resin were mixed, dispersed and formed into a sheet shape by the bar coating method. Fe-Si based polycrystalline fine powder, Fe-Si-Cr based amorphous fine powder and Fe-Si-Nb-Cu-B based nanocrystalline fine powder with an average particle were used as the starting soft magnetic powder. In addition, submicron Fe-Si-Cr based powder was used to further increase the packing density of the magnetic powder in the composite sheet. As the evaluation of the magnetic sheet, saturation magnetization, coercivity, relative magnetic permeability and loss-tangent in 10MHz - hundreds MHz were measured. A magnetic sheet using the nanocrystalline powder and submicron powder showed high relative permeability of 13 and low loss-tangent of 0.05 at 100MHz.
- 28 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-5
Crossed Anisotropy Multilayered Nanogranular Films Combining High Permeability, Ferromagnetic Resonance Frequency, and Resistivity
In-plane isotropic crossed anisotropy multilayer for high-frequency magnetics was fabricated using in-plane uniaxial anisotropic nanogranular film owing to its high permeability, ferromagnetic resonance (FMR) frequency, and electrical DC resistivity. The multilayer exhibited in-plane isotropy, and enabled us to combine permeability of approximately 100, FMR frequency of approximately 3 GHz, and resistivity of approximately 5 μΩ·m. Moreover, a low damping factor of 0.0148 was obtained; hence the multilayer is available for a low loss up to 1 GHz. Meanwhile, underlayer and cap layer were necessary for improving the isotropy of the multilayer. The results can be attributed to the interfacial stress.
- 28 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-5
Crossed Anisotropy Multilayered Nanogranular Films Combining High Permeability, Ferromagnetic Resonance Frequency, and Resistivity
In-plane isotropic crossed anisotropy multilayer for high-frequency magnetics was fabricated using in-plane uniaxial anisotropic nanogranular film owing to its high permeability, ferromagnetic resonance (FMR) frequency, and electrical DC resistivity. The multilayer exhibited in-plane isotropy, and enabled us to combine permeability of approximately 100, FMR frequency of approximately 3 GHz, and resistivity of approximately 5 μΩ·m. Moreover, a low damping factor of 0.0148 was obtained; hence the multilayer is available for a low loss up to 1 GHz. Meanwhile, underlayer and cap layer were necessary for improving the isotropy of the multilayer. The results can be attributed to the interfacial stress.
- 14 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-6
Fabrication of Fe-Based Nanocrystalline Powder-Pressed Magnetic Core and Application to Planar Reactor for Hundreds of kHz or Beyond
In this study, to decrease coercivity and iron loss for the Fe-Si-B-Nb-Cu-C nanocrystalline powder-pressed magnetic core for hundreds kHz or beyond, a post annealing after pressing the Fe-Si-B-Nb-Cu-C amorphous powder was executed for nanocrytallization and release of the residual strain induced through the pressing the powder. In addition, novel fabrication procedure for obtaining the small coercivity powdered magnetic core was proposed. It was found that the fabricated Fe-Si-B-Nb-Cu-C nanocrystalline powdered magnetic core exhibited a saturation magnetization of 0.91 T, coercvity of 123 A/m, relative permeability of 32.5 and iron losses of 105 kW/m 3 at 100kHz, 50mT and 2194 kW/m 3 at 1MHz, 50mT. From the iron loss break-down for the fabricated Fe-Si-B-Nb-Cu-C nanocrystalline powdered magnetic core, its hysteresis and eddy current losses were smaller than those of Fe-Si-B-C-Cr powder-pressed magnetic core. In addition, a planar reactor was fabricated using the powder-pressed magnetic core, which had a size of 47×44×16 mm, DC coil resistance of 7.3mΩ, inductance of 12.1 μH, Q -factor of about 127 at 1MHz and inductance drop of 4.1% at a superimposed DC current of 30A.
- 14 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-6
Fabrication of Fe-Based Nanocrystalline Powder-Pressed Magnetic Core and Application to Planar Reactor for Hundreds of kHz or Beyond
In this study, to decrease coercivity and iron loss for the Fe-Si-B-Nb-Cu-C nanocrystalline powder-pressed magnetic core for hundreds kHz or beyond, a post annealing after pressing the Fe-Si-B-Nb-Cu-C amorphous powder was executed for nanocrytallization and release of the residual strain induced through the pressing the powder. In addition, novel fabrication procedure for obtaining the small coercivity powdered magnetic core was proposed. It was found that the fabricated Fe-Si-B-Nb-Cu-C nanocrystalline powdered magnetic core exhibited a saturation magnetization of 0.91 T, coercvity of 123 A/m, relative permeability of 32.5 and iron losses of 105 kW/m 3 at 100kHz, 50mT and 2194 kW/m 3 at 1MHz, 50mT. From the iron loss break-down for the fabricated Fe-Si-B-Nb-Cu-C nanocrystalline powdered magnetic core, its hysteresis and eddy current losses were smaller than those of Fe-Si-B-C-Cr powder-pressed magnetic core. In addition, a planar reactor was fabricated using the powder-pressed magnetic core, which had a size of 47×44×16 mm, DC coil resistance of 7.3mΩ, inductance of 12.1 μH, Q -factor of about 127 at 1MHz and inductance drop of 4.1% at a superimposed DC current of 30A.
- Open Access
Performance Comparison of Ferrite and Nanocrystalline Cores for Medium-Frequency Transformer of Dual Active Bridge DC-DC Converter
This article reports an investigation into ferrite and nanocrystalline materials for the medium-frequency transformer of a dual active bridge DC-DC converter, which plays a key role in the converter’s efficiency and power density. E65 MnZn ferrite cores and toroidal and cut nanocrystalline cores are selected for the construction of 20-kHz transformers. Transformer performance is evaluated with a 1.1-kW (42–54 V)/400 V dual active bridge DC-DC converter with single-phase shift and extended phase shift modulations. The experimental results indicate that the toroidal nanocrystalline transformer had the best performance with an efficiency range of 98.5–99.2% and power density of 12 W/cm3, whereas the cut-core nanocrystalline transformer had an efficiency range of 98.4–99.1% with a power density of 9 W/cm3, and the ferrite transformer had an efficiency range of 97.6–98.8% with a power density of 6 W/cm3. A small mismatch in the circuit parameters is found to cause saturation in the nanocrystalline toroidal core, due to its high permeability. The analytical and experimental results suggest that cut nanocrystalline cores are suitable for the dual active bridge DC-DC converter transformers with switching frequencies up to 100 kHz.
Open AccessPerformance Comparison of Ferrite and Nanocrystalline Cores for Medium-Frequency Transformer of Dual Active Bridge DC-DC Converter
This article reports an investigation into ferrite and nanocrystalline materials for the medium-frequency transformer of a dual active bridge DC-DC converter, which plays a key role in the converter’s efficiency and power density. E65 MnZn ferrite cores and toroidal and cut nanocrystalline cores are selected for the construction of 20-kHz transformers. Transformer performance is evaluated with a 1.1-kW (42–54 V)/400 V dual active bridge DC-DC converter with single-phase shift and extended phase shift modulations. The experimental results indicate that the toroidal nanocrystalline transformer had the best performance with an efficiency range of 98.5–99.2% and power density of 12 W/cm3, whereas the cut-core nanocrystalline transformer had an efficiency range of 98.4–99.1% with a power density of 9 W/cm3, and the ferrite transformer had an efficiency range of 97.6–98.8% with a power density of 6 W/cm3. A small mismatch in the circuit parameters is found to cause saturation in the nanocrystalline toroidal core, due to its high permeability. The analytical and experimental results suggest that cut nanocrystalline cores are suitable for the dual active bridge DC-DC converter transformers with switching frequencies up to 100 kHz.
- Open Access
- 1 January 2019
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Journal of Industry Applications
- Vol. 8 (1) , 51-56
Loss Reduction of LLC Resonant Converter using Magnetocoated Wire
- 1 January 2019
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Journal of Industry Applications
- Vol. 8 (1) , 51-56
Open AccessLoss Reduction of LLC Resonant Converter using Magnetocoated Wire
- Open Access
Relative Estimation of Water Content for Flat-Type Inductive-Based Oil Palm Fruit Maturity Sensor
The paper aims to study the sensor that identifies the maturity of oil palm fruit bunches by using a flat-type inductive concept based on a resonant frequency technique. Conventionally, a human grader is used to inspect the ripeness of the oil palm fresh fruit bunch (FFB) which can be inconsistent and inaccurate. There are various new methods that are proposed with the intention to grade the ripeness of the oil palm FFB, but none has taken the inductive concept. In this study, the resonance frequency of the air coil is investigated. Samples of oil palm FFB are tested with frequencies ranging from 20 Hz to 10 MHz and the results obtained show a linear relationship between the graph of the resonance frequency (MHz) against time (Weeks). It is observed that the resonance frequencies obtained for Week 10 (pre-mature) and Week 18 (mature) are around 8.5 MHz and 9.8 MHz, respectively. These results are compared with the percentage of the moisture content. Hence, the inductive method of the oil palm fruit maturity sensor can be used to detect the change in water content for ripeness detection of the oil palm FFB.
Open AccessRelative Estimation of Water Content for Flat-Type Inductive-Based Oil Palm Fruit Maturity Sensor
The paper aims to study the sensor that identifies the maturity of oil palm fruit bunches by using a flat-type inductive concept based on a resonant frequency technique. Conventionally, a human grader is used to inspect the ripeness of the oil palm fresh fruit bunch (FFB) which can be inconsistent and inaccurate. There are various new methods that are proposed with the intention to grade the ripeness of the oil palm FFB, but none has taken the inductive concept. In this study, the resonance frequency of the air coil is investigated. Samples of oil palm FFB are tested with frequencies ranging from 20 Hz to 10 MHz and the results obtained show a linear relationship between the graph of the resonance frequency (MHz) against time (Weeks). It is observed that the resonance frequencies obtained for Week 10 (pre-mature) and Week 18 (mature) are around 8.5 MHz and 9.8 MHz, respectively. These results are compared with the percentage of the moisture content. Hence, the inductive method of the oil palm fruit maturity sensor can be used to detect the change in water content for ripeness detection of the oil palm FFB.
- 1 January 2012
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Sensors and Micromachines
- Vol. 132 (2) , 25-30
Wideband Visible Wavelength Range MEMS Fabry-Perot Tunable Filter with Ag Alloy Mirror
- 1 January 2012
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Sensors and Micromachines
- Vol. 132 (2) , 25-30
Wideband Visible Wavelength Range MEMS Fabry-Perot Tunable Filter with Ag Alloy Mirror
- Open Access
- 1 January 2000
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Industry Applications
- Vol. 120 (11) , 1376-1381
Measurement of the Source Impedance of Conducted Emission Using Mode Separable LISN
- 1 January 2000
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Industry Applications
- Vol. 120 (11) , 1376-1381
Open AccessMeasurement of the Source Impedance of Conducted Emission Using Mode Separable LISN