Joel Winiger
Joel Winiger has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Juerg Leuthold
ETH Zurich
5 shared publications - Daniel Chelladurai
Institute of Electromagnetic Fields ETH Zurich Zurich Switzerland
3 shared publications - Ueli Koch
ETH Zurich, Institute of Electromagnetic Fields, Zurich, Switzerland
3 shared publications - Andreas Messner
Institute of Electromagnetic Fields (IEF), ETH Zurich, 8092 Zurich, Switzerland
2 shared publications - David Moor
ETH Zurich
2 shared publications Killian Keller
Institute of Electromagnetic Fields
2 shared publications
Latest Publications
- Open Access
- 29 May 2025
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 15 (6) , 1356
Synthetic materials with high pockels coefficient for plasmonic modulators
We present simulations of Pockels materials based on nonlinearities arising from intersubband transitions (ISBT). To elevate the Pockels coefficient to the order of nm/V, the ISBT resonance is tuned close to the operation point. This comes at the expense of increased material losses due to quasi-resonant operation. Such Pockels materials are of high interest for implementation in plasmonic modulators. In these modulators the higher material losses do not significantly impact the device performance, as overall losses are dominated by plasmonic waveguide losses. With this approach, voltage-loss-length (VπLα) products on the order of ∼15 V dB may be achieved with plasmonic losses. Such efficiencies are comparable to those with photonic modulators. The Pockels effect coefficient calculations have been performed using self-consistent Schrödinger-Poisson simulations with consideration of many-body effects. Furthermore, we investigated the influence of RF field screening and surface roughness on the efficiency of the ISB transition-mediated Pockels materials.
- 29 May 2025
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 15 (6) , 1356
Open AccessSynthetic materials with high pockels coefficient for plasmonic modulators
We present simulations of Pockels materials based on nonlinearities arising from intersubband transitions (ISBT). To elevate the Pockels coefficient to the order of nm/V, the ISBT resonance is tuned close to the operation point. This comes at the expense of increased material losses due to quasi-resonant operation. Such Pockels materials are of high interest for implementation in plasmonic modulators. In these modulators the higher material losses do not significantly impact the device performance, as overall losses are dominated by plasmonic waveguide losses. With this approach, voltage-loss-length (VπLα) products on the order of ∼15 V dB may be achieved with plasmonic losses. Such efficiencies are comparable to those with photonic modulators. The Pockels effect coefficient calculations have been performed using self-consistent Schrödinger-Poisson simulations with consideration of many-body effects. Furthermore, we investigated the influence of RF field screening and surface roughness on the efficiency of the ISB transition-mediated Pockels materials.
- 25 January 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (3) , 4511-4524
Measuring dielectric and electro-optic responses of thin films using plasmonic devices
This paper introduces a simple method for the measurement of the relative permittivity and the Pockels coefficient of electro-optic (EO) materials in a waveguide up to sub-THz frequencies. By miniaturizing the device and making use of plasmonics, the complexities of traditional methods are mitigated. This work elaborates the fabrication tolerance and simplicity of the method, and highlights its applicability to various materials, substrates and configurations. The method is showcased using drop-casted perovskite barium titanate (BaTiO3, BTO) nano-particle thin-films and it has previously been used to measure epitaxial thin film BTO. In this work we show the effective relative permittivity of drop casted BTO to be εeff ∼ 30 at 200 MHz, dropping to ∼ 18 at 67 GHz and similarly, the effective Pockels coefficient was found to be reff ∼ 16 at 350 MHz and ∼ 8 at 70 GHz. These values are a factor > 50 below the values found for thin film BTO. Yet, the fact that the method can be applied to such different samples and Pockels strengths gives testimony to its versatility and sensitivity.
- 25 January 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (3) , 4511-4524
Measuring dielectric and electro-optic responses of thin films using plasmonic devices
This paper introduces a simple method for the measurement of the relative permittivity and the Pockels coefficient of electro-optic (EO) materials in a waveguide up to sub-THz frequencies. By miniaturizing the device and making use of plasmonics, the complexities of traditional methods are mitigated. This work elaborates the fabrication tolerance and simplicity of the method, and highlights its applicability to various materials, substrates and configurations. The method is showcased using drop-casted perovskite barium titanate (BaTiO3, BTO) nano-particle thin-films and it has previously been used to measure epitaxial thin film BTO. In this work we show the effective relative permittivity of drop casted BTO to be εeff ∼ 30 at 200 MHz, dropping to ∼ 18 at 67 GHz and similarly, the effective Pockels coefficient was found to be reff ∼ 16 at 350 MHz and ∼ 8 at 70 GHz. These values are a factor > 50 below the values found for thin film BTO. Yet, the fact that the method can be applied to such different samples and Pockels strengths gives testimony to its versatility and sensitivity.
- Open Access
- 17 October 2023
- Published by Wiley in Advanced Materials Interfaces
- Vol. 11 (1)
PLD Epitaxial Thin‐Film BaTiO3 on MgO − Dielectric and Electro‐Optic Properties
The study demonstrates high‐quality pulsed‐laser‐deposited (PLD) barium titanate (BTO) thin‐films on a magnesium oxide substrate. The frequency response of the relative permittivity (dielectric constant) and the linear electro‐optical coefficient (Pockels coefficient) are measured. At 0.2 GHz, the Pockels coefficient is fitted to be r42 ≈ 1030 pm V−1. It decreases to ≈390 pm V−1 at 10 GHz after which it remains constant up to 70 GHz. The unbiased BTO permittivity is measured to be εa ≈ 7600 at 0.2 GHz, dropping to ≈1100 at 67 GHz, while the biased BTO had a permittivity εa ≈ 2000 at 0.2 GHz, dropping to ≈500 at 67 GHz. These results fill an important experimental characterization gap for high‐speed BTO applications and show the high quality of PLD‐grown BTO films. Lastly, the material's crystalline quality is characterized and the domain distribution is imaged. The findings enable the design and fabrication of a new generation of BTO‐based components for sensing and communications.
- 17 October 2023
- Published by Wiley in Advanced Materials Interfaces
- Vol. 11 (1)
Open AccessPLD Epitaxial Thin‐Film BaTiO3 on MgO − Dielectric and Electro‐Optic Properties
The study demonstrates high‐quality pulsed‐laser‐deposited (PLD) barium titanate (BTO) thin‐films on a magnesium oxide substrate. The frequency response of the relative permittivity (dielectric constant) and the linear electro‐optical coefficient (Pockels coefficient) are measured. At 0.2 GHz, the Pockels coefficient is fitted to be r42 ≈ 1030 pm V−1. It decreases to ≈390 pm V−1 at 10 GHz after which it remains constant up to 70 GHz. The unbiased BTO permittivity is measured to be εa ≈ 7600 at 0.2 GHz, dropping to ≈1100 at 67 GHz, while the biased BTO had a permittivity εa ≈ 2000 at 0.2 GHz, dropping to ≈500 at 67 GHz. These results fill an important experimental characterization gap for high‐speed BTO applications and show the high quality of PLD‐grown BTO films. Lastly, the material's crystalline quality is characterized and the domain distribution is imaged. The findings enable the design and fabrication of a new generation of BTO‐based components for sensing and communications.
- Open Access
Sol–Gel Barium Titanate Nanohole Array as a Nonlinear Metasurface and a Photonic Crystal
The quest of a nonlinear optical material that can be easily nanostructured over a large surface area is still ongoing. Here, we demonstrate a nanoimprinted nonlinear barium titanate 2D nanohole array that shows the optical properties of a 2D photonic crystal and a metasurface, depending on the direction of the optical axis. The challenge of nanostructuring the inert metal‐oxide is resolved by direct soft nanoimprint lithography with sol–gel derived barium titanate enabling critical dimensions of 120 nm with aspect ratios of five. The nanohole array exhibits a photonic bandgap in the infrared range when probed along the slab axis, while lattice resonant states are observed in out‐of‐plane transmission configuration. The enhanced light‐matter interaction from the resonant structure enables to increase in the second‐harmonic generation in the near‐ultraviolet by a factor of 18 illustrating the potential in the flexible fabrication technique for barium titanate photonic devices.
Open AccessSol–Gel Barium Titanate Nanohole Array as a Nonlinear Metasurface and a Photonic Crystal
The quest of a nonlinear optical material that can be easily nanostructured over a large surface area is still ongoing. Here, we demonstrate a nanoimprinted nonlinear barium titanate 2D nanohole array that shows the optical properties of a 2D photonic crystal and a metasurface, depending on the direction of the optical axis. The challenge of nanostructuring the inert metal‐oxide is resolved by direct soft nanoimprint lithography with sol–gel derived barium titanate enabling critical dimensions of 120 nm with aspect ratios of five. The nanohole array exhibits a photonic bandgap in the infrared range when probed along the slab axis, while lattice resonant states are observed in out‐of‐plane transmission configuration. The enhanced light‐matter interaction from the resonant structure enables to increase in the second‐harmonic generation in the near‐ultraviolet by a factor of 18 illustrating the potential in the flexible fabrication technique for barium titanate photonic devices.
- Open Access
- 30 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (12) , 3825-3831
Plasmonic Ferroelectric Modulator Monolithically Integrated on SiN for 216 GBd Data Transmission
A high-speed plasmonic barium titanate (BTO, BaTiO 3 ) Mach-Zehnder modulator is presented. We combine nanoscale plasmonics with BTO as solid-state active material and silicon nitride (SiN) for versatile and low loss waveguiding, and integrate them in a monolithic platform. We demonstrate a plasmonic BTO modulator processed onto foundry-produced SiN. The 15 µm long high-speed modulator features a flat electro-optic frequency response up to 70 GHz and is expected to be flat way beyond. A low V π L product of 144 Vµm is shown. Data experiments reaching 216 Gbit/s with a 216 GBd 2PAM signal and 256 Gbit/s with a 128 GBd 4PAM signal are demonstrated. The merger of the versatile silicon nitride platform with high-speed plasmonics using the highly nonlinear ferroelectric BTO is an attractive solution as a future Tb/s optical interconnect platform.
- 30 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (12) , 3825-3831
Open AccessPlasmonic Ferroelectric Modulator Monolithically Integrated on SiN for 216 GBd Data Transmission
A high-speed plasmonic barium titanate (BTO, BaTiO 3 ) Mach-Zehnder modulator is presented. We combine nanoscale plasmonics with BTO as solid-state active material and silicon nitride (SiN) for versatile and low loss waveguiding, and integrate them in a monolithic platform. We demonstrate a plasmonic BTO modulator processed onto foundry-produced SiN. The 15 µm long high-speed modulator features a flat electro-optic frequency response up to 70 GHz and is expected to be flat way beyond. A low V π L product of 144 Vµm is shown. Data experiments reaching 216 Gbit/s with a 216 GBd 2PAM signal and 256 Gbit/s with a 128 GBd 4PAM signal are demonstrated. The merger of the versatile silicon nitride platform with high-speed plasmonics using the highly nonlinear ferroelectric BTO is an attractive solution as a future Tb/s optical interconnect platform.
- Open Access
- 18 May 2021
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 21 (11) , 4539-4545
Broadband Metallic Fiber-to-Chip Couplers and a Low-Complexity Integrated Plasmonic Platform
We present a plasmonic platform featuring efficient, broadband metallic fiber-to-chip couplers that directly interface plasmonic slot waveguides, such as compact and high-speed electro-optic modulators. The metallic gratings exhibit an experimental fiber-to-slot coupling efficiency of −2.7 dB with −1.4 dB in simulations with the same coupling principle. Further, they offer a huge spectral window with a 3 dB passband of 350 nm. The technology relies on a vertically arranged layer stack, metal–insulator–metal waveguides, and fiber-to-slot couplers and is formed in only one lithography step with a minimum feature size of 250 nm. As an application example, we fabricate new modulator devices with an electro-optic organic material in the slot waveguide and reach 50 and 100 Gbit/s data modulation in the O- and C-bands within the same device. The devices’ broad spectral bandwidth and their relaxed fabrication may render them suitable for experiments and applications in the scope of sensing, nonlinear optics, or telecommunications.
- 18 May 2021
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 21 (11) , 4539-4545
Open AccessBroadband Metallic Fiber-to-Chip Couplers and a Low-Complexity Integrated Plasmonic Platform
We present a plasmonic platform featuring efficient, broadband metallic fiber-to-chip couplers that directly interface plasmonic slot waveguides, such as compact and high-speed electro-optic modulators. The metallic gratings exhibit an experimental fiber-to-slot coupling efficiency of −2.7 dB with −1.4 dB in simulations with the same coupling principle. Further, they offer a huge spectral window with a 3 dB passband of 350 nm. The technology relies on a vertically arranged layer stack, metal–insulator–metal waveguides, and fiber-to-slot couplers and is formed in only one lithography step with a minimum feature size of 250 nm. As an application example, we fabricate new modulator devices with an electro-optic organic material in the slot waveguide and reach 50 and 100 Gbit/s data modulation in the O- and C-bands within the same device. The devices’ broad spectral bandwidth and their relaxed fabrication may render them suitable for experiments and applications in the scope of sensing, nonlinear optics, or telecommunications.