Val. V. Firsanov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Val. V. Firsanov has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
A. I. Endogur
Moscow Aviation Institute (National Research University)
1 shared publicationB. V. Boitsov
Moscow Aviation Institute (National Research University)
1 shared publicationCh. N. Doan
State Technical University
1 shared publicationChan Ngok Doan
1 shared publication- L. M. Gavva
Moscow Aviation Institute (NRU)
1 shared publication - L. M. Gavva
Moscow Aviation Institute (NRU), Moscow, Russia
1 shared publication
Latest Publications
- Open Access
- 15 December 2023
- Published by PNRPU Publishing House in PNRPU Mechanics Bulletin
- No. 3,p. 43-52
BASE NEUTRAL SURFASE SELECTION FOR OPTIMAL DESIGN OF STRUCTURALLY-ANISOTROPIC AIRCRAFT PANELS MADE FROM COMPOSITE MATERIALS WITH REFINED BUCKLING THEORY RESTRICTIONS
The aim of this study is the approach to the optimal design of structurally-anisotropic aircraft bearing surface panels with the restrictions according to the refined buckling theory for the optimal size-weight design implementation. The panels are subjected to the distributed constant compressive loading applied to the edges in the skin plane in the longitudinal direction. The panel contour boundary conditions are assumed to be the particular case with conformable boundary restrictions for the plane problem and problem of bending. The optimal design problem statement and analytical solution are formulated to determine the geometry parameters of a flat rectangular multilayer panel made from composite materials with the eccentric longitudinal and lateral stiffening set being of minimal mass. The equal-buckling condition is the optimal design base. The general bending mode of buckling and multi-wave torsion mode of buckling must have the same occurrence probability while the buckling margin tends to one. The optimal design problem is reduced to the mathematic conditional extremum investigation of the goal weight function with multiple variables using the analytical and numerical methods. New mathematic model relations for the buckling problem investigation of structurally-anisotropic composite panels are presented. The primary scientific novelty of this research is the further development of the thin-walled elastic rib theory related to the contact problem for the skin and rib with an improved rib model. The analytical solution is reduced to determine the displacements of a base neutral surface that may be select arbitrarily. The schematization of the panel as structurally-anisotropic one has been proposed as a design model when the critical forces of total bending mode of buckling are determined. For a multi-wave torsion buckling study, one should use the generalized function techniques for the discrete stringer stiffness. The solution of the strained surface differential equation of an eighth order is designed by a trigonometric series in the closed form. The results of the optimal design with the refined buckling restrictions based on refined buckling analysis calculations offer opportunities to reduce and optimize the weight characteristics of aircraft elements.
- 15 December 2023
- Published by PNRPU Publishing House in PNRPU Mechanics Bulletin
- No. 3,p. 43-52
Open AccessBASE NEUTRAL SURFASE SELECTION FOR OPTIMAL DESIGN OF STRUCTURALLY-ANISOTROPIC AIRCRAFT PANELS MADE FROM COMPOSITE MATERIALS WITH REFINED BUCKLING THEORY RESTRICTIONS
The aim of this study is the approach to the optimal design of structurally-anisotropic aircraft bearing surface panels with the restrictions according to the refined buckling theory for the optimal size-weight design implementation. The panels are subjected to the distributed constant compressive loading applied to the edges in the skin plane in the longitudinal direction. The panel contour boundary conditions are assumed to be the particular case with conformable boundary restrictions for the plane problem and problem of bending. The optimal design problem statement and analytical solution are formulated to determine the geometry parameters of a flat rectangular multilayer panel made from composite materials with the eccentric longitudinal and lateral stiffening set being of minimal mass. The equal-buckling condition is the optimal design base. The general bending mode of buckling and multi-wave torsion mode of buckling must have the same occurrence probability while the buckling margin tends to one. The optimal design problem is reduced to the mathematic conditional extremum investigation of the goal weight function with multiple variables using the analytical and numerical methods. New mathematic model relations for the buckling problem investigation of structurally-anisotropic composite panels are presented. The primary scientific novelty of this research is the further development of the thin-walled elastic rib theory related to the contact problem for the skin and rib with an improved rib model. The analytical solution is reduced to determine the displacements of a base neutral surface that may be select arbitrarily. The schematization of the panel as structurally-anisotropic one has been proposed as a design model when the critical forces of total bending mode of buckling are determined. For a multi-wave torsion buckling study, one should use the generalized function techniques for the discrete stringer stiffness. The solution of the strained surface differential equation of an eighth order is designed by a trigonometric series in the closed form. The results of the optimal design with the refined buckling restrictions based on refined buckling analysis calculations offer opportunities to reduce and optimize the weight characteristics of aircraft elements.
- 1 January 2019
- Published by Allerton Press in Journal of Machinery Manufacture and Reliability
- Vol. 48 (1) , 54-60
The Basic Stress—Strain State of a Circular Plate of Variable Thickness Based on a Nonclassical Theory
A mathematical model of the basic stress-strain state of a circular plate with thickness varying asymmetrically under axisymmetric loading is developed. The method of direct asymptotic integration of...
- 1 January 2019
- Published by Allerton Press in Journal of Machinery Manufacture and Reliability
- Vol. 48 (1) , 54-60
The Basic Stress—Strain State of a Circular Plate of Variable Thickness Based on a Nonclassical Theory
A mathematical model of the basic stress-strain state of a circular plate with thickness varying asymmetrically under axisymmetric loading is developed. The method of direct asymptotic integration of...
- 1 October 2018
- Published by Allerton Press in Russian Aeronautics (Iz VUZ)
- Vol. 61 (4) , 524-532
Stress-Strain State and Buckling Problems of Structurally-Anisotropic Aircraft Panels Made of Composite Materials in View of Production Technology
The main relations of a mathematical model for analyzing the stress-strain state and buckling of structurally-anisotropic panels made of composite materials are proposed. The mathematical model of a...
- 1 October 2018
- Published by Allerton Press in Russian Aeronautics (Iz VUZ)
- Vol. 61 (4) , 524-532
Stress-Strain State and Buckling Problems of Structurally-Anisotropic Aircraft Panels Made of Composite Materials in View of Production Technology
The main relations of a mathematical model for analyzing the stress-strain state and buckling of structurally-anisotropic panels made of composite materials are proposed. The mathematical model of a...
- 1 May 2018
- Published by Allerton Press in Journal of Machinery Manufacture and Reliability
- Vol. 47 (3) , 241-248
The Stressed State of the “Boundary Layer” Type in Cylindrical Shells Investigated according to a Nonclassical Theory
Two variants of a refined theory for calculating the stress–strain state in the boundary zones of cylindrical shells are presented. The relevant mathematical models are based on equations of the...
- 1 May 2018
- Published by Allerton Press in Journal of Machinery Manufacture and Reliability
- Vol. 47 (3) , 241-248
The Stressed State of the “Boundary Layer” Type in Cylindrical Shells Investigated according to a Nonclassical Theory
Two variants of a refined theory for calculating the stress–strain state in the boundary zones of cylindrical shells are presented. The relevant mathematical models are based on equations of the...
- 1 November 2016
- Published by Allerton Press in Journal of Machinery Manufacture and Reliability
- Vol. 45 (6) , 515-521
Study of stress-deformed state of rectangular plates based on nonclassical theory
- 1 November 2016
- Published by Allerton Press in Journal of Machinery Manufacture and Reliability
- Vol. 45 (6) , 515-521
Study of stress-deformed state of rectangular plates based on nonclassical theory
- 1 July 2016
- Published by Allerton Press in Russian Engineering Research
- Vol. 36 (7) , 532-534
Stress concentration at the edge of a circular hole with unilateral annular reinforcement
- 1 July 2016
- Published by Allerton Press in Russian Engineering Research
- Vol. 36 (7) , 532-534
Stress concentration at the edge of a circular hole with unilateral annular reinforcement
- 1 September 2015
- Published by Allerton Press in Russian Engineering Research
- Vol. 35 (9) , 650-652
Design of compressor rotors in gas-turbine engines to minimize flutter
A method is proposed for predicting rotor flutter in the compressors of gas-turbine engines in energy terms. The method is tested by simulations.
- 1 September 2015
- Published by Allerton Press in Russian Engineering Research
- Vol. 35 (9) , 650-652
Design of compressor rotors in gas-turbine engines to minimize flutter
A method is proposed for predicting rotor flutter in the compressors of gas-turbine engines in energy terms. The method is tested by simulations.
- 1 January 2015
- Published by Begell House Inc. Publishers in Composites: Mechanics, Computations, Applications: An International Journal
- Vol. 6 (2) , 135-166
INVESTIGATION OF THE STATICS AND FREE VIBRATIONS OF CYLINDRICAL SHELLS ON THE BASIS OF A NONCLASSICAL THEORY
Based on an energy-consistent approach, the equations of motion of an orthotropic shell of arbitrary geometry whose deflected mode is described by equations of the three-dimensional theory of elasticity have been obtained. Three-dimensional equations are reduced to two-dimensional ones by means of the principle of virtual displacements and by the expansion of displacement components into polynomial series in the coordinate system, which is normal to the middle plane of the shell. Modified boundary conditions for standard cases of shell fixturing are formulated. As an example, the paper considers static deformation and natural vibrations of a circular cylindrical shell. Equilibrium equations in displacements and boundary conditions are presented. Calculation of the shell's deflected mode is carried out by means of Laplace transform, thus twofold reducing the number of arbitrary constants in integration of the system of differential equations of the problem. The values of natural frequencies are determined by the Bubnov-Galerkin variational method. The effect of different types of boundary conditions on the deflected mode and the values of natural frequencies is analyzed. The results of calculation of the natural frequencies obtained in this work and those obtained by some versions of the classical Donnell-Mushtari and Goldenweiser-Novozhilov theory, as well as by the three-dimensional theory of elasticity are compared. The results obtained can be used in calculations and strength and durability tests of aviation and space-rocket structures, and also of different-purpose engineering structures.
- 1 January 2015
- Published by Begell House Inc. Publishers in Composites: Mechanics, Computations, Applications: An International Journal
- Vol. 6 (2) , 135-166
INVESTIGATION OF THE STATICS AND FREE VIBRATIONS OF CYLINDRICAL SHELLS ON THE BASIS OF A NONCLASSICAL THEORY
Based on an energy-consistent approach, the equations of motion of an orthotropic shell of arbitrary geometry whose deflected mode is described by equations of the three-dimensional theory of elasticity have been obtained. Three-dimensional equations are reduced to two-dimensional ones by means of the principle of virtual displacements and by the expansion of displacement components into polynomial series in the coordinate system, which is normal to the middle plane of the shell. Modified boundary conditions for standard cases of shell fixturing are formulated. As an example, the paper considers static deformation and natural vibrations of a circular cylindrical shell. Equilibrium equations in displacements and boundary conditions are presented. Calculation of the shell's deflected mode is carried out by means of Laplace transform, thus twofold reducing the number of arbitrary constants in integration of the system of differential equations of the problem. The values of natural frequencies are determined by the Bubnov-Galerkin variational method. The effect of different types of boundary conditions on the deflected mode and the values of natural frequencies is analyzed. The results of calculation of the natural frequencies obtained in this work and those obtained by some versions of the classical Donnell-Mushtari and Goldenweiser-Novozhilov theory, as well as by the three-dimensional theory of elasticity are compared. The results obtained can be used in calculations and strength and durability tests of aviation and space-rocket structures, and also of different-purpose engineering structures.
- 1 September 2014
- Published by Allerton Press in Journal of Machinery Manufacture and Reliability
- Vol. 43 (5) , 349-357
Natural oscillations of general shells based on nonclassical theory
Two-dimensional equations of the dynamics of the theory of general shells and appropriate boundary conditions that make it possible to take into account the transverse shear and compression of the shell are constructed based on three-dimensional equations of elasticity theory and the Lagrange variational principle by expanding the displacements in the coordinate normal to the middle surface. Natural oscillations of a circular cylindrical shell are considered. Frequencies of natural oscillations are determined by the Bubnov-Galerkin method. The impact of different types of boundary conditions and geometric parameters of the shell on the value of natural frequencies are analyzed. Simulation results are compared with different variants of the classical theory of shells, as well as with three-dimensional elasticity theory.
- 1 September 2014
- Published by Allerton Press in Journal of Machinery Manufacture and Reliability
- Vol. 43 (5) , 349-357
Natural oscillations of general shells based on nonclassical theory
Two-dimensional equations of the dynamics of the theory of general shells and appropriate boundary conditions that make it possible to take into account the transverse shear and compression of the shell are constructed based on three-dimensional equations of elasticity theory and the Lagrange variational principle by expanding the displacements in the coordinate normal to the middle surface. Natural oscillations of a circular cylindrical shell are considered. Frequencies of natural oscillations are determined by the Bubnov-Galerkin method. The impact of different types of boundary conditions and geometric parameters of the shell on the value of natural frequencies are analyzed. Simulation results are compared with different variants of the classical theory of shells, as well as with three-dimensional elasticity theory.
- 1 October 2012
- Published by Allerton Press in Russian Aeronautics (Iz VUZ)
- Vol. 55 (4) , 366-372
Elastoplastic stresses of a shell of revolution made from the material with linear hardening loaded by a force at the pole
We analyze the elastoplastic stress-strain state of an axisymmetrical parabolic type shell of revolution at the pole of which the concentrated force is applied. The shell is considered as a momentless one, and the properties of its material are schematized by the tensile diagram with linear hardening. The problem is solved in stresses, the corresponding equations are constructed, and the solution is given.
- 1 October 2012
- Published by Allerton Press in Russian Aeronautics (Iz VUZ)
- Vol. 55 (4) , 366-372
Elastoplastic stresses of a shell of revolution made from the material with linear hardening loaded by a force at the pole
We analyze the elastoplastic stress-strain state of an axisymmetrical parabolic type shell of revolution at the pole of which the concentrated force is applied. The shell is considered as a momentless one, and the properties of its material are schematized by the tensile diagram with linear hardening. The problem is solved in stresses, the corresponding equations are constructed, and the solution is given.