ESEik Schiegnitz

Eik Schiegnitz

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Eik Schiegnitz has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Clinical outcome of alveolar ridge augmentation with individualized CAD-CAM-produced titanium mesh

    by K. Sagheb, E. Schiegnitz, M. Moergel, C. Walter, B. Al-Nawas, W. Wagner

    The augmentation of the jaw has been and continues to be a sophisticated therapy in implantology. Modern CAD-CAM technologies lead to revival of old and established augmentation techniques such as the use of titanium mesh (TM) for bone augmentation. The aim of this retrospective study was to evaluate the clinical outcome of an individualized CAD-CAM-produced TM based on the CT/DVT-DICOM data of the patients for the first time. In 17 patients, 21 different regions were augmented with an individualized CAD-CAM-produced TM (Yxoss CBR®, Filderstadt, Germany). For the augmentation, a mixture of autologous bone and deproteinized bovine bone mineral (DBBM) or autologous bone alone was used. Reentry with explantation of the TM and simultaneous implantation of 44 implants were performed after 6 months. Preoperative and 6-month postoperative cone beam computed tomographies (CBCT) were performed to measure the gained bone height. The success rate for the bone grafting procedure was 100%. Thirty-three percent of cases presented an exposure of the TM during the healing period. However, premature removal of these exposed meshes was not necessary. Exposure rate in augmentations performed with mid-crestal incisions was higher than in augmentations performed with a modified poncho incision (45.5 vs. 20%, p = 0.221). In addition, exposure rates in the maxilla were significantly higher than in the mandible (66.7 vs. 8.3%, p = 0.009). Gender, smoking, periodontal disease, gingiva type, used augmentation material, and used membrane had no significant influence on the exposure rate (p > 0.05). The mean vertical augmentation was 6.5 ± 1.7 mm, and the mean horizontal augmentation was 5.5 ± 1.9 mm. Implant survival rate after a mean follow-up of 12 ± 6 months after reentry was 100%. Within the limits of the retrospective character of this study, this study shows for the first time that individualized CAD-CAM TM provide a sufficient and safe augmentation technique, especially for vertical and combined defects. However, the soft tissue handling for sufficient mesh covering remains one of the most critical steps using this technique.


  • Open Access

    Vital Life‐Threatening Hematoma after Implant Insertion in the Anterior Mandible: A Case Report and Review of the Literature

    by Eik Schiegnitz, Maximilian Moergel, Wilfried Wagner

    Dental implant insertion is considered a safe and reliable surgical procedure and severe complications are seldom reported. However, we present a case of a 52‐year‐old patient who attended our Department of Oral and Maxillofacial Surgery, Johannes Gutenberg University Medical Center, Mainz, with spreading hematoma in the floor of the mouth and acute airway obstruction after insertion of a dental implant in the anterior mandible. The hematoma was removed and submentally drained by a silicon drainage. However, the progressive swelling of the tongue and the floor of the mouth necessitated a temporary tracheotomy for three days. The review of the literature summarizes guidelines for prevention and management of this life‐threatening complication.


  • Vertical Osteoconductive Characteristics of Titanium Implants with Calcium‐Phosphate‐Coated Surfaces – A Pilot Study in Rabbits

    by Eik Schiegnitz, Victor Palarie, Viorel Nacu, Bilal Al‐Nawas, Peer Wolfgang Kämmerer

    Introduction: Osteoconductive characteristics of different implant surface coatings are in the focus of current interest. The aim of the present study was to compare the vertical osteoconductivity at the implant shoulder of supracrestal inserted calcium‐phosphate coated implants (SLA‐CaP) with conventional sand‐blasted/acid‐etched (SLA) implants in a rabbit model.Materials and Methods: SLA‐CaP and SLA implants were inserted bilaterally in the mandible of four rabbits in a split‐mouth design. The implants were placed 2 mm supracrestal. After 3 weeks, at the left and right implant shoulder, the percentage of linear bone fill (PLF) as well as bone‐implant contact (BIC‐D) were determined.Results: After 3 weeks, newly formed woven bone could be found at the shoulder of the most of both surface‐treated implants (75%). PLF was significantly higher in SLA‐CaP implants (11.2% vs. 46.5%; n = 8, p = .008). BIC‐D was significantly increased in the SLA‐CaP implants (13.0% vs. 71.4%; n = 8, p < .001) as well.Conclusion: The results of this study show for the first time that calcium‐phosphate coated surfaces on supracrestal inserted implants have vertical osteoconductive characteristics and increase the bone‐implant contact at the implant shoulder significantly in a rabbit model. In clinical long‐term settings, these implants may contribute to a better vertical bone height.


  • GDF 15 as an anti-apoptotic, diagnostic and prognostic marker in oral squamous cell carcinoma

    by E. Schiegnitz, P.W. Kämmerer, F.P. Koch, M. Krüger, M. Berres, B. Al-Nawas