ASAnandhamurugan Surya

Anandhamurugan Surya

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anandhamurugan Surya has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Effect of Dimensionless Heat Transfer Parameters on Charging in a Latent Heat Thermal Energy Storage System Using Spherical Phase Change Material Balls

    by Anandhamurugan Surya, Ramasamy Prakash, Malcolm Nithin Arul Gomez, Abhinav Badrinarayan Davey, Ranganathan Suryakumar Hariharan

    Latent heat thermal energy storage (LHTES) systems are implemented to mitigate temporal mismatches between energy generation and demand, and accurate characterization of the governing dimensionless parameters is essential for predicting charging behavior in packed configurations of spherical PCM balls under forced convection. This study presents an experimental investigation of a packed‐bed LHTES module containing spherical PCM balls encapsulating myristic acid, with water as the heat transfer fluid (HTF). Experiments were conducted at HTF inlet temperatures of 70°C and 75°C and volumetric flow rates of 200, 300, and 400 LPH. The transient evolution of Stefan, Reynolds, Rayleigh, Nusselt, Stanton, and Biot numbers was evaluated and correlated with melting progression, charging duration, and average thermal power. Increasing the inlet temperature from 70°C to 75°C decreased charging time by 31.03%, 36.00%, and 36.84% at 200, 300, and 400 LPH, respectively, indicating intensified sensible‐to‐latent heat transfer. Higher Reynolds numbers enhanced convective transport, increased interfacial heat flux, and accelerated phase front propagation within the spherical PCM balls. Biot numbers below 0.1 signified predominant external thermal resistance and nearly uniform internal temperature distribution, facilitating effective radial heat diffusion. The coupled behavior of Rayleigh and Nusselt numbers clarified the interaction between buoyancy‐induced effects and external convection during melting. The results establish a dimensionless thermo‐fluidic framework for describing charging characteristics in packed beds of spherical PCM balls and provide experimentally substantiated guidance for performance‐oriented design and optimization of PCM‐based thermal energy storage systems for renewable and industrial applications.

  • Parametric Analysis of Heat Transfer Fluid Effects on Thermal Stratification in a Latent Heat Energy Storage System

    by Anandhamurugan Surya, Ramasamy Prakash, Govindasamy Ramaiyan Pandiyan Balakumaran, Sekar Roopesh Varun, Seenuvasan Nishanth

    Thermal stratification significantly affects the performance of thermal energy storage (TES) systems, especially in domestic hot water (DHW) applications. While stratification in sensible heat storage is well studied, its optimization in phase change material (PCM)‐based systems has received less attention. This article examines the effects of heat transfer fluid (HTF) inlet temperature and flow rate on stratification and energy performance in a PCM‐based TES tank. Experiments are conducted at flow rates of 200, 300, and 400 LPH with inlet temperatures of 70 and 75 °C. Higher inlet temperatures reduce PCM charging time by 31.03%, 36.00%, and 36.84% for the respective flow rates. Stratification, measured by the MIX number, improves with higher flow rates and temperatures, as shown by lower values. Elevated HTF temperatures increase the temperature gradient, enhancing sensible heating and raising average storage temperature during PCM melting. The Richardson number rose initially but declined rapidly as melting reduced the thermal gradient. After melting, charging efficiency decreases due to weakened stratification. These findings emphasize the importance of controlling HTF operating conditions to enhance stratification and TES efficiency, supporting the development of advanced control strategies and designs for PCM‐based TES in DHW and renewable energy applications.

  • Open Access

    Development of Alumina-Titania Composite Layers on Stainless Steel through the Detonation Spray Method and Investigation of Salt Spray Corrosion Behavior along with Surface Examination

    by A. Surya, R. Prakash, P. Senthil Kumar, G. Bharath Balji

    Almost every metal and alloy corrodes when used in high-temperature applications. To combat this problem, ceramic coatings on the metals can be deposited for better thermal and corrosion behavior. The present study applies an alumina-titania (Al2O3-TiO2) ceramic coating to the stainless steel (SS) surface using a detonation spray process. The surface of the coated SS is probed by optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The clear differences between coated and uncoated SS have been observed based on the SEM images. The XRD pattern indicates that the Al2O3-TiO2 coating on SS has been successfully deposited. The hardness of coated and uncoated SS surfaces is determined by using the Micro Vickers hardness tester, which claims that the hardness of the SS surface has decreased after coating. Salt spray tests were used to examine the corrosion behavior of coated and uncoated SS after 12 and 24hours. After 12hours, no corrosion was observed on the SS. After 24hours, however, significant corrosion of uncoated SS is observed, and the coated SS shows negligible corrosion. Based on the study, it is claimed that an Al2O3-TiO2 coating on SS has improved its corrosion behavior significantly.